Published 2001-06-13 · Federal Register document 01-14532
Airworthiness Directives; Dornier Model 328-300 Series Airplanes
Publication summary
This amendment adopts a new airworthiness directive (AD), applicable to certain Dornier Model 328-300 series airplanes, that requires replacement of the hydraulic line between the main hydraulic pump and the pulsation damper in hydraulic system "B" with a new hydraulic flex hose. This action is necessary to prevent cracking in the hydraulic line (due to a production defect), leading to heavy leakage in hydraulic system "B," which could impair the functioning of the airplane's flaps, roll spoilers, inner ground spoilers, and nose wheel steering. This action is intended to address the identified unsafe condition.
Why this record is shown
Source: Federal Register annual FAA metadata. Acquired 2026-09-03T22:23:03.835669+00:00. The title, summary and date are source facts.
- Source revision
- federal_register_ad_metadata_2001-8d66ddb74aa17366
- Source row
- results[214]
- Raw source SHA-256
- 8d66ddb74aa17366596c5f6ccb4e6d04532df19ae027b6fa003379bdedb52c7e
Final-rule publication
Recorded publication clauses
- AD identifier printed in this edition
- 2001-12-04
- Effective date printed in this edition
- 2001-07-18
Some source clauses remain unstructured. Read the complete publication for conditions that have not been interpreted here.
Read 2 complete recorded clauses
Applicability wording · Applicability
Applicability: Model 328-300 series airplanes, serial numbers
3105 to 3175 inclusive; certificated in any category.
Note 1: This AD applies to each airplane identified in the
preceding applicability provision, regardless of whether it has been
[[Page 31836]]
modified, altered, or repaired in the area subject to the
requirements of this AD. For airplanes that have been modified,
altered, or repaired so that the performance of the requirements of
this AD is affected, the owner/operator must request approval for an
alternative method of compliance in accordance with paragraph (b) of
this AD. The request should include an assessment of the effect of
the modification, alteration, or repair on the unsafe condition
addressed by this AD; and, if the unsafe condition has not been
eliminated, the request should include specific proposed actions to
address it.
Exact source excerpt. Text positions 6484–7369, end exclusive, in the original decoded publication. SHA-256: 8b22771c8e704f480fe22adffc0a127810c62418200acc412ef99821bcd1e4fa
Compliance and requirements
Compliance: Required as indicated, unless accomplished
previously.
To prevent a crack in the hydraulic line, leading to heavy
leakage in hydraulic system ``B,'' which could impair the
functioning of the airplane's flaps, roll spoilers, inner ground
spoilers, and nose wheel steering, accomplish the following:
Replacement
(a) Within 45 days from the effective date of this AD: Remove
the hydraulic hose having part number (P/N) 001D291A2050010 between
the main pump 50DA and the pulsation damper, and replace it with a
new hose having P/N 001D291A1102000, in accordance with Dornier
Service Bulletin SB-328J-29-040, dated June 8, 2000.
Alternative Methods of Compliance
(b) An alternative method of compliance or adjustment of the
compliance time that provides an acceptable level of safety may be
used if approved by the Manager, International Branch, ANM-116,
Transport Airplane Directorate, FAA. Operators shall submit their
requests through an appropriate FAA Principal Maintenance Inspector,
who may add comments and then send it to the Manager, International
Branch, ANM-116.
Note 2: Information concerning the existence of approved
alternative methods of compliance with this AD, if any, may be
obtained from the International Branch, ANM-116.
Special Flight Permits
(c) Special flight permits may be issued in accordance with
sections Secs. 21.197 and 21.199 of the Federal Aviation Regulations
(14 CFR 21.197 and 21.199) to operate the airplane to a location
where the requirements of this AD can be accomplished.
Incorporation by Reference
(d) The actions shall be done in accordance with Dornier Service
Bulletin SB-328J-29-040, dated June 8, 2000. This incorporation by
reference was approved by the Director of the Federal Register in
accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be
obtained from Fairchild Dornier, Dornier Luftfahrt GmbH, P.O. Box
1103, D-82230 Wessling, Germany. Copies may be inspected at the FAA,
Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton,
Washington; or at the Office of the Federal Register, 800 North
Capitol Street, NW., suite 700, Washington, DC.
Note 3: The subject of this AD is addressed in German
airworthiness directive 2000-378, dated December 14, 2000.
Effective Date
(e) This amendment becomes effective on July 18, 2001.
Exact source excerpt. Text positions 7369–9751, end exclusive, in the original decoded publication. SHA-256: 3a8cf1a94c0aebfe994f9233f706af201f4f198308ed1ca6b33cf03bc03f780b
No replacement link has been established from this edition. The complete historical rule chain and current legal effect remain unknown.
Find all recorded historical references to AD 2001-12-04 · 0 printed reference observations in this pinned collection.
These are observations from one dated publication. Current legal status is unknown; aircraft applicability, installed configuration, compliance and burden require separate evidence. Missing or unparsed conditions remain unknown.
Why these observations are shown
They were extracted offline from the same immutable official HTML source as the complete recorded text. The dated source wording, original text coordinates and exact quote digests are retained. PDF/text agreement and current regulatory effect have not been qualified.
Observation revision: whole-ad-publication-clause-observations-1.0.1. Text SHA-256: 466ecaf4c68621ae20d535c1e5c0bc0797a73246fa5627c01ab273e422daa19c. Source manifest: 681e0cfeb4bdc4e1d0e3bdfaaebc7c4b89b7ea25a8e0386b1eb4b2bf5ee1ea1d.
Official source · 2001-06-13
Publication text
This is the complete recorded text of this dated publication.
Current legal effect is unknown. Aircraft applicability, installed configuration and compliance require separate evidence. PDF/text agreement has not been evaluated.
Read the complete official publication text
[Federal Register Volume 66, Number 114 (Wednesday, June 13, 2001)]
[Rules and Regulations]
[Pages 31835-31836]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 01-14532]
========================================================================
Rules and Regulations
Federal Register
________________________________________________________________________
This section of the FEDERAL REGISTER contains regulatory documents
having general applicability and legal effect, most of which are keyed
to and codified in the Code of Federal Regulations, which is published
under 50 titles pursuant to 44 U.S.C. 1510.
The Code of Federal Regulations is sold by the Superintendent of Documents.
Prices of new books are listed in the first FEDERAL REGISTER issue of each
week.
========================================================================
Federal Register / Vol. 66, No. 114 / Wednesday, June 13, 2001 /
Rules and Regulations
[[Page 31835]]
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. 2000-NM-386-AD; Amendment 39-12259; AD 2001-12-04]
RIN 2120-AA64
Airworthiness Directives; Dornier Model 328-300 Series Airplanes
AGENCY: Federal Aviation Administration, DOT.
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: This amendment adopts a new airworthiness directive (AD),
applicable to certain Dornier Model 328-300 series airplanes, that
requires replacement of the hydraulic line between the main hydraulic
pump and the pulsation damper in hydraulic system ``B'' with a new
hydraulic flex hose. This action is necessary to prevent cracking in
the hydraulic line (due to a production defect), leading to heavy
leakage in hydraulic system ``B,'' which could impair the functioning
of the airplane's flaps, roll spoilers, inner ground spoilers, and nose
wheel steering. This action is intended to address the identified
unsafe condition.
DATES: Effective July 18, 2001.
The incorporation by reference of certain publications listed in
the regulations is approved by the Director of the Federal Register as
of July 18, 2001.
ADDRESSES: The service information referenced in this AD may be
obtained from Fairchild Dornier, Dornier Luftfahrt GmbH, P.O. Box 1103,
D-82230 Wessling, Germany. This information may be examined at the
Federal Aviation Administration (FAA), Transport Airplane Directorate,
Rules Docket, 1601 Lind Avenue, SW., Renton, Washington; or at the
Office of the Federal Register, 800 North Capitol Street, NW., suite
700, Washington, DC.
FOR FURTHER INFORMATION CONTACT: Dan Rodina, Aerospace Engineer, ANM-
116, FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW.,
Renton, Washington 98055-4056; telephone (425) 227-2125; fax (425) 227-
1149.
SUPPLEMENTARY INFORMATION: A proposal to amend part 39 of the Federal
Aviation Regulations (14 CFR part 39) to include an airworthiness
directive (AD) that is applicable to certain Dornier Model 328-300
series airplanes was published in the Federal Register on March 29,
2001 (66 FR 17099). That action proposed to require replacement of the
hydraulic line between the main hydraulic pump and the pulsation damper
in hydraulic system ``B'' with a new hydraulic flex hose.
Comments
Interested persons have been afforded an opportunity to participate
in the making of this amendment. No comments were submitted in response
to the proposal or the FAA's determination of the cost to the public.
Conclusion
The FAA has determined that air safety and the public interest
require the adoption of the rule as proposed.
Cost Impact
The FAA estimates that 17 airplanes of U.S. registry will be
affected by this AD, that it will take approximately 1 work hour per
airplane to accomplish the required replacement, and that the average
labor rate is $60 per work hour. There is no charge for required parts.
Based on these figures, the cost impact of the AD on U.S. operators is
estimated to be $1,020, or $60 per airplane.
The cost impact figure discussed above is based on assumptions that
no operator has yet accomplished any of the requirements of this AD
action, and that no operator would accomplish those actions in the
future if this AD were not adopted. The cost impact figures discussed
in AD rulemaking actions represent only the time necessary to perform
the specific actions actually required by the AD. These figures
typically do not include incidental costs, such as the time required to
gain access and close up, planning time, or time necessitated by other
administrative actions.
Regulatory Impact
The regulations adopted herein will not have a substantial direct
effect on the States, on the relationship between the national
Government and the States, or on the distribution of power and
responsibilities among the various levels of government. Therefore, it
is determined that this final rule does not have federalism
implications under Executive Order 13132.
For the reasons discussed above, I certify that this action (1) is
not a ``significant regulatory action'' under Executive Order 12866;
(2) is not a ``significant rule'' under DOT Regulatory Policies and
Procedures (44 FR 11034, February 26, 1979); and (3) will not have a
significant economic impact, positive or negative, on a substantial
number of small entities under the criteria of the Regulatory
Flexibility Act. A final evaluation has been prepared for this action
and it is contained in the Rules Docket. A copy of it may be obtained
from the Rules Docket at the location provided under the caption
ADDRESSES.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
Accordingly, pursuant to the authority delegated to me by the
Administrator, the Federal Aviation Administration amends part 39 of
the Federal Aviation Regulations (14 CFR part 39) as follows:
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
2. Section 39.13 is amended by adding the following new
airworthiness directive:
2001-12-04 Dornier Luftfahrt Gmbh: Amendment 39-12259. Docket 2000-
NM-386-AD.
Applicability: Model 328-300 series airplanes, serial numbers
3105 to 3175 inclusive; certificated in any category.
Note 1: This AD applies to each airplane identified in the
preceding applicability provision, regardless of whether it has been
[[Page 31836]]
modified, altered, or repaired in the area subject to the
requirements of this AD. For airplanes that have been modified,
altered, or repaired so that the performance of the requirements of
this AD is affected, the owner/operator must request approval for an
alternative method of compliance in accordance with paragraph (b) of
this AD. The request should include an assessment of the effect of
the modification, alteration, or repair on the unsafe condition
addressed by this AD; and, if the unsafe condition has not been
eliminated, the request should include specific proposed actions to
address it.
Compliance: Required as indicated, unless accomplished
previously.
To prevent a crack in the hydraulic line, leading to heavy
leakage in hydraulic system ``B,'' which could impair the
functioning of the airplane's flaps, roll spoilers, inner ground
spoilers, and nose wheel steering, accomplish the following:
Replacement
(a) Within 45 days from the effective date of this AD: Remove
the hydraulic hose having part number (P/N) 001D291A2050010 between
the main pump 50DA and the pulsation damper, and replace it with a
new hose having P/N 001D291A1102000, in accordance with Dornier
Service Bulletin SB-328J-29-040, dated June 8, 2000.
Alternative Methods of Compliance
(b) An alternative method of compliance or adjustment of the
compliance time that provides an acceptable level of safety may be
used if approved by the Manager, International Branch, ANM-116,
Transport Airplane Directorate, FAA. Operators shall submit their
requests through an appropriate FAA Principal Maintenance Inspector,
who may add comments and then send it to the Manager, International
Branch, ANM-116.
Note 2: Information concerning the existence of approved
alternative methods of compliance with this AD, if any, may be
obtained from the International Branch, ANM-116.
Special Flight Permits
(c) Special flight permits may be issued in accordance with
sections Secs. 21.197 and 21.199 of the Federal Aviation Regulations
(14 CFR 21.197 and 21.199) to operate the airplane to a location
where the requirements of this AD can be accomplished.
Incorporation by Reference
(d) The actions shall be done in accordance with Dornier Service
Bulletin SB-328J-29-040, dated June 8, 2000. This incorporation by
reference was approved by the Director of the Federal Register in
accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be
obtained from Fairchild Dornier, Dornier Luftfahrt GmbH, P.O. Box
1103, D-82230 Wessling, Germany. Copies may be inspected at the FAA,
Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton,
Washington; or at the Office of the Federal Register, 800 North
Capitol Street, NW., suite 700, Washington, DC.
Note 3: The subject of this AD is addressed in German
airworthiness directive 2000-378, dated December 14, 2000.
Effective Date
(e) This amendment becomes effective on July 18, 2001.
Issued in Renton, Washington, on June 4, 2001.
Donald L. Riggin,
Acting Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. 01-14532 Filed 6-12-01; 8:45 am]
BILLING CODE 4910-13-P
Why this text is shown
The complete text was extracted from the official GovInfo HTML edition for this publication. Acquired 2026-10-09T04:29:09.680522+00:00. Text extraction preserves the recorded source wording; it does not determine current requirements.
Open the captured official edition
- Source SHA-256
- 93a64c85ee469a018905c307c7bc5ad51e4776f7704b8ff922914118058bebf2
- Text SHA-256
- 466ecaf4c68621ae20d535c1e5c0bc0797a73246fa5627c01ab273e422daa19c
Return to the full metadata catalog · Search complete publication text · Explore retained publication text and evidence
Coverage and limits
These are dated publication metadata, recorded clauses and literal source observations. Word, model-label, header and reference matches do not establish current legal effect, manufacturer/model identity, aircraft applicability, installed configuration or compliance.
The collection uses 33 explicit annual source snapshots. Source captures and operative-text qualifications have separate states. Missing information remains unknown.