Back to publication catalog

Published 2001-06-27 · Federal Register document 01-15935

Airworthiness Directives; Dornier Model 328-300 Series Airplanes

Publication summary

This amendment adopts a new airworthiness directive (AD), applicable to certain Dornier Model 328-300 series airplanes, that requires replacing the brake assemblies with modified brake assemblies. The actions specified by this AD are intended to prevent overheating of the brakes, which could result in cracked pistons and consequent leakage and burning of the hydraulic fluid. This action is intended to address the identified unsafe condition.

Why this record is shown

Source: Federal Register annual FAA metadata. Acquired 2026-09-03T22:23:03.835669+00:00. The title, summary and date are source facts.

Source revision
federal_register_ad_metadata_2001-8d66ddb74aa17366
Source row
results[241]
Raw source SHA-256
8d66ddb74aa17366596c5f6ccb4e6d04532df19ae027b6fa003379bdedb52c7e

Final-rule publication

Recorded publication clauses

AD identifier printed in this edition
2001-13-08
Effective date printed in this edition
2001-08-01

Some source clauses remain unstructured. Read the complete publication for conditions that have not been interpreted here.

Read 2 complete recorded clauses
Applicability wording · Applicability
    Applicability: Model 328-300 series airplanes, certificated in 
any category, serial numbers 3105 through 3144 inclusive, 3146, 
3148, 3151 through 3154 inclusive, 3158, and 3159.

    Note 1: This AD applies to each airplane identified in the 
preceding applicability provision, regardless of whether it has been 
modified, altered, or repaired in the area subject to the 
requirements of this AD. For airplanes that have been modified, 
altered, or repaired so that the performance of the requirements of 
this AD is affected, the

[[Page 34091]]

owner/operator must request approval for an alternative method of 
compliance in accordance with paragraph (c) of this AD. The request 
should include an assessment of the effect of the modification, 
alteration, or repair on the unsafe condition addressed by this AD; 
and, if the unsafe condition has not been eliminated, the request 
should include specific proposed actions to address it.

Exact source excerpt. Text positions 5494–6442, end exclusive, in the original decoded publication. SHA-256: 4dd07793054c4d294e268933c1b53b493a0b539e64f863a10fb0f08c44393b5b

Compliance and requirements
    Compliance: Required as indicated, unless accomplished 
previously.
    To prevent overheating of the brakes, which could result in 
cracked pistons and consequent leakage and burning of the hydraulic 
fluid, accomplish the following:

Brake Piston Replacement

    (a) Within 7 weeks after the effective date of this AD, replace 
the left and right brake assemblies having part number (P/N) 
AHA2227-2 with modified brake assemblies having P/N AHA2227-3, in 
accordance with Dornier Service Bulletin SB-328J-32-029, Revision 1, 
dated August 4, 2000.

    Note 2: Replacement of the brake assemblies prior to the 
effective date of this AD in accordance with Dornier Service 
Bulletin SB-328J-32-029, dated June 14, 2000, is also acceptable for 
compliance with the requirements of paragraph (a) of this AD.

Spares

    (b) As of the effective date of this AD, no person may install a 
brake assembly having P/N AHA2227-2 on any airplane.

Alternative Methods of Compliance

    (c) An alternative method of compliance or adjustment of the 
compliance time that provides an acceptable level of safety may be 
used if approved by the Manager, International Branch, ANM-116, 
Transport Airplane Directorate, FAA. Operators shall submit their 
requests through an appropriate FAA Principal Maintenance Inspector, 
who may add comments and then send it to the Manager, International 
Branch, ANM-116.

    Note 3: Information concerning the existence of approved 
alternative methods of compliance with this AD, if any, may be 
obtained from the International Branch, ANM-116.

Special Flight Permits

    (d) Special flight permits may be issued in accordance with 
sections 21.197 and 21.199 of the Federal Aviation Regulations (14 
CFR 21.197 and 21.199) to operate the airplane to a location where 
the requirements of this AD can be accomplished.

Incorporation by Reference

    (e) The actions shall be done in accordance with Dornier Service 
Bulletin SB-328J-32-029, Revision 1, dated August 4, 2000. This 
incorporation by reference was approved by the Director of the 
Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 
51. Copies may be obtained from FAIRCHILD DORNIER, DORNIER Luftfahrt 
GmbH, P.O. Box 1103, D-82230 Wessling, Germany. Copies may be 
inspected at the FAA, Transport Airplane Directorate, 1601 Lind 
Avenue, SW., Renton, Washington; or at the Office of the Federal 
Register, 800 North Capitol Street, NW., suite 700, Washington, DC.

    Note 4: The subject of this AD is addressed in German 
airworthiness directive 2000-288, dated September 21, 2000.

Effective Date

    (f) This amendment becomes effective on August 1, 2001.

Exact source excerpt. Text positions 6442–9121, end exclusive, in the original decoded publication. SHA-256: f9520a7f58df50b3d551b0749ce9caf4fc60f71b60c740f8e10ca03ca4ff80b6

No replacement link has been established from this edition. The complete historical rule chain and current legal effect remain unknown.

Find all recorded historical references to AD 2001-13-08 · 0 printed reference observations in this pinned collection.

These are observations from one dated publication. Current legal status is unknown; aircraft applicability, installed configuration, compliance and burden require separate evidence. Missing or unparsed conditions remain unknown.

Why these observations are shown

They were extracted offline from the same immutable official HTML source as the complete recorded text. The dated source wording, original text coordinates and exact quote digests are retained. PDF/text agreement and current regulatory effect have not been qualified.

Observation revision: whole-ad-publication-clause-observations-1.0.1. Text SHA-256: 88edbafa8cf54214fb3f7475da8370fdeff1027ad685242122c926a631d80a5c. Source manifest: 96e8f398360d26424e916468cd630c12bde5a43011ab3d14bb7975196dfab84f.

Official source · 2001-06-27

Publication text

This is the complete recorded text of this dated publication.

Current legal effect is unknown. Aircraft applicability, installed configuration and compliance require separate evidence. PDF/text agreement has not been evaluated.

Read the complete official publication text
[Federal Register Volume 66, Number 124 (Wednesday, June 27, 2001)]
[Rules and Regulations]
[Pages 34090-34091]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 01-15935]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. 2000-NM-339-AD; Amendment 39-12288; AD 2001-13-08]
RIN 2120-AA64


Airworthiness Directives; Dornier Model 328-300 Series Airplanes

AGENCY: Federal Aviation Administration, DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: This amendment adopts a new airworthiness directive (AD), 
applicable to certain Dornier Model 328-300 series airplanes, that 
requires replacing the brake assemblies with modified brake assemblies. 
The actions specified by this AD are intended to prevent overheating of 
the brakes, which could result in cracked pistons and consequent 
leakage and burning of the hydraulic fluid. This action is intended to 
address the identified unsafe condition.

DATES: Effective August 1, 2001.
    The incorporation by reference of certain publications listed in 
the regulations is approved by the Director of the Federal Register as 
of August 1, 2001.

ADDRESSES: The service information referenced in this AD may be 
obtained from Fairchild Dornier, Dornier Luftfahrt GmbH, P.O. Box 1103, 
D-82230 Wessling, Germany. This information may be examined at these 
Federal Aviation Administration (FAA), Transport Airplane Directorate, 
Rules Docket, 1601 Lind Avenue, SW., Renton, Washington; or at the 
Office of the Federal Register, 800 North Capitol Street, NW., suite 
700, Washington, DC.

FOR FURTHER INFORMATION CONTACT: Dan Rodina, Aerospace Engineer, 
International Branch, ANM-116, FAA, Transport Airplane Directorate, 
1601 Lind Avenue, SW., Renton, Washington 98055-4056; telephone (425) 
227-2125; fax (425) 227-1149.

SUPPLEMENTARY INFORMATION: A proposal to amend part 39 of the Federal 
Aviation Regulations (14 CFR part 39) to include an airworthiness 
directive (AD) that is applicable to certain Dornier Model 328-300 
series airplanes was published in the Federal Register on May 4, 2001 
(66 FR 22484). That action proposed to require replacing the brake 
assemblies with modified brake assemblies.

Comments

    Interested persons have been afforded an opportunity to participate 
in the making of this amendment. No comments were submitted in response 
to the proposal or the FAA's determination of the cost to the public.

Conclusion

    The FAA has determined that air safety and the public interest 
require the adoption of the rule as proposed.

Cost Impact

    The FAA estimates that 8 airplanes of U.S. registry will be 
affected by this AD, that it will take approximately 9 work hours per 
airplane to accomplish the required actions, and that the average labor 
rate is $60 per work hour. Required parts will be provided at the 
manufacturer at no cost to operators. Based on these figures, the cost 
impact of the AD on U.S. operators is estimated to be $4,320, or $540 
per airplane.
    The cost impact figure discussed above is based on assumptions that 
no operator has yet accomplished any of the requirements of this AD 
action, and that no operator would accomplish those actions in the 
future if this AD were not adopted. The cost impact figures discussed 
in AD rulemaking actions represent only the time necessary to perform 
the specific actions actually required by the AD. These figures 
typically do not include incidental costs, such as the time required to 
gain access and close up, planning time, or time necessitated by other 
administrative actions.

Regulatory Impact

    The regulations adopted herein will not have a substantial direct 
effect on the States, on the relationship between the national 
Government and the States, or on the distribution of power and 
responsibilities among the various levels of government. Therefore, it 
is determined that this final rule does not have federalism 
implications under Executive Order 13132.
    For the reasons discussed above, I certify that this action (1) is 
not a ``significant regulatory action'' under Executive Order 12866; 
(2) is not a ``significant rule'' under DOT Regulatory Policies and 
Procedures (44 FR 11034, February 26, 1979); and (3) will not have a 
significant economic impact, positive or negative, on a substantial 
number of small entities under the criteria of the Regulatory 
Flexibility Act. A final evaluation has been prepared for this action 
and it is contained in the Rules Docket. A copy of it may be obtained 
from the Rules Docket at the location provided under the caption 
ADDRESSES.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, pursuant to the authority delegated to me by the 
Administrator, the Federal Aviation Administration amends part 39 of 
the Federal Aviation Regulations (14 CFR part 39) as follows:

PART 39--AIRWORTHINESS DIRECTIVES

    1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.

Sec. 39.13  [Amended]

    2. Section 39.13 is amended by adding the following new 
airworthiness directive:

2001-13-08  Dornier Luftfahrt GmbH: Amendment 39-12288. Docket 2000-
NM-339-AD.

    Applicability: Model 328-300 series airplanes, certificated in 
any category, serial numbers 3105 through 3144 inclusive, 3146, 
3148, 3151 through 3154 inclusive, 3158, and 3159.

    Note 1: This AD applies to each airplane identified in the 
preceding applicability provision, regardless of whether it has been 
modified, altered, or repaired in the area subject to the 
requirements of this AD. For airplanes that have been modified, 
altered, or repaired so that the performance of the requirements of 
this AD is affected, the

[[Page 34091]]

owner/operator must request approval for an alternative method of 
compliance in accordance with paragraph (c) of this AD. The request 
should include an assessment of the effect of the modification, 
alteration, or repair on the unsafe condition addressed by this AD; 
and, if the unsafe condition has not been eliminated, the request 
should include specific proposed actions to address it.

    Compliance: Required as indicated, unless accomplished 
previously.
    To prevent overheating of the brakes, which could result in 
cracked pistons and consequent leakage and burning of the hydraulic 
fluid, accomplish the following:

Brake Piston Replacement

    (a) Within 7 weeks after the effective date of this AD, replace 
the left and right brake assemblies having part number (P/N) 
AHA2227-2 with modified brake assemblies having P/N AHA2227-3, in 
accordance with Dornier Service Bulletin SB-328J-32-029, Revision 1, 
dated August 4, 2000.

    Note 2: Replacement of the brake assemblies prior to the 
effective date of this AD in accordance with Dornier Service 
Bulletin SB-328J-32-029, dated June 14, 2000, is also acceptable for 
compliance with the requirements of paragraph (a) of this AD.

Spares

    (b) As of the effective date of this AD, no person may install a 
brake assembly having P/N AHA2227-2 on any airplane.

Alternative Methods of Compliance

    (c) An alternative method of compliance or adjustment of the 
compliance time that provides an acceptable level of safety may be 
used if approved by the Manager, International Branch, ANM-116, 
Transport Airplane Directorate, FAA. Operators shall submit their 
requests through an appropriate FAA Principal Maintenance Inspector, 
who may add comments and then send it to the Manager, International 
Branch, ANM-116.

    Note 3: Information concerning the existence of approved 
alternative methods of compliance with this AD, if any, may be 
obtained from the International Branch, ANM-116.

Special Flight Permits

    (d) Special flight permits may be issued in accordance with 
sections 21.197 and 21.199 of the Federal Aviation Regulations (14 
CFR 21.197 and 21.199) to operate the airplane to a location where 
the requirements of this AD can be accomplished.

Incorporation by Reference

    (e) The actions shall be done in accordance with Dornier Service 
Bulletin SB-328J-32-029, Revision 1, dated August 4, 2000. This 
incorporation by reference was approved by the Director of the 
Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 
51. Copies may be obtained from FAIRCHILD DORNIER, DORNIER Luftfahrt 
GmbH, P.O. Box 1103, D-82230 Wessling, Germany. Copies may be 
inspected at the FAA, Transport Airplane Directorate, 1601 Lind 
Avenue, SW., Renton, Washington; or at the Office of the Federal 
Register, 800 North Capitol Street, NW., suite 700, Washington, DC.

    Note 4: The subject of this AD is addressed in German 
airworthiness directive 2000-288, dated September 21, 2000.

Effective Date

    (f) This amendment becomes effective on August 1, 2001.

    Issued in Renton, Washington, on June 19, 2001.
Kalene C. Yanamura,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 01-15935 Filed 6-26-01; 8:45 am]
BILLING CODE 4910-13-P


Why this text is shown

The complete text was extracted from the official GovInfo HTML edition for this publication. Acquired 2026-10-09T04:28:43.537873+00:00. Text extraction preserves the recorded source wording; it does not determine current requirements.

Open the captured official edition

Source SHA-256
92786d0fcdf942973f248ccd490752eca66910ebfe515c744efbf26090147cc6
Text SHA-256
88edbafa8cf54214fb3f7475da8370fdeff1027ad685242122c926a631d80a5c

Return to the full metadata catalog · Search complete publication text · Explore retained publication text and evidence

Coverage and limits

These are dated publication metadata, recorded clauses and literal source observations. Word, model-label, header and reference matches do not establish current legal effect, manufacturer/model identity, aircraft applicability, installed configuration or compliance.

The collection uses 33 explicit annual source snapshots. Source captures and operative-text qualifications have separate states. Missing information remains unknown.