Airworthiness Directives; Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model EMB-135 and -145 Series Airplanes

[Federal Register Volume 68, Number 174 (Tuesday, September 9, 2003)]
[Rules and Regulations]
[Page 53032]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 03-22889]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. 2002-NM-88-AD; Amendment 39-13189; AD 2003-12-04]
RIN 2120-AA64


Airworthiness Directives; Empresa Brasileira de Aeronautica S.A. 
(EMBRAER) Model EMB-135 and -145 Series Airplanes

AGENCY: Federal Aviation Administration, DOT.

ACTION: Final rule; correction.

-----------------------------------------------------------------------

SUMMARY: This document corrects a typographical error that appeared in 
airworthiness directive (AD) 2003-12-04, which was published in the 
Federal Register on June 12, 2003 (68 FR 35157). The typographical 
error resulted in an incorrect part number for the replacement supports 
for the engine bleed air duct. This AD is applicable to certain EMBRAER 
Model EMB-135 and -145 series airplanes. This AD requires replacing the 
four GAMAH clamp/sleeve joints on an engine bleed air duct with new 
threaded coupling assemblies; for certain airplanes, this AD also 
requires replacing the two supports for the engine bleed air duct with 
two new supports.

DATES: Effective July 17, 2003.

FOR FURTHER INFORMATION CONTACT: Dan Rodina, Aerospace Engineer, 
International Branch, ANM-116, FAA, Transport Airplane Directorate, 
1601 Lind Avenue, SW., Renton, Washington 98055-4056; telephone (425) 
227-2125; fax (425) 227-1149.

SUPPLEMENTARY INFORMATION: Airworthiness Directive (AD) 2003-12-04, 
amendment 39-13189, applicable to certain EMBRAER Model EMB-135 and -
145 series airplanes, was published in the Federal Register on June 12, 
2003 (68 FR 35157). That AD requires replacing the four GAMAH clamp/
sleeve joints on an engine bleed air duct with new threaded coupling 
assemblies; for certain airplanes, that AD also requires replacing the 
two supports for the engine bleed air duct with two new supports.
    As published, paragraph (a)(2) of the AD cites an incorrect part 
number (145-35923-007) for the replacement supports for the engine 
bleed air duct. The correct part number is 145-35923-015.
    Since no other part of the regulatory information has been changed, 
the final rule is not being republished in the Federal Register.
    The effective date of this AD remains July 17, 2003.


Sec.  39.13  [Corrected]

0
On page 35158, in the second column, paragraph (a)(2) of AD 2003-12-04 
is corrected to read as follows:
* * * * *
    (2) For airplanes having serial numbers listed in paragraph 3.G. of 
the Accomplishment Instructions of the service bulletin: Replace the 
two supports for the engine bleed air duct with two new supports having 
part number 145-35923-015.
* * * * *

    Issued in Renton, Washington, on September 3, 2003.
Ali Bahrami,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 03-22889 Filed 9-8-03; 8:45 am]
BILLING CODE 4910-13-P

The complete text was extracted from the official GovInfo HTML edition for this publication. Acquired 2026-10-09T04:10:51.740052+00:00. Text extraction preserves the recorded source wording; it does not determine current requirements.

Open the captured official edition

Source SHA-256

129e5420b29bae2e97c6f4c4caed4722b3e345a3548b1742c593d5fe95229116

Text SHA-256

7bb7e73766798dbe4734e41bf56f44f2f421573bf39bde9c4648af0879ac2346