Back to publication catalog

Published 2005-03-14 · Federal Register document 05-4828

Airworthiness Directives; Airbus Model A300 B4-622R and A300 F4-622R Airplanes

Publication summary

The FAA is adopting a new airworthiness directive (AD) for certain Airbus Model A300 B4-622R and A300 F4-622R airplanes. This AD requires doing a one-time inspection to determine if lower guide fittings for the forward doors are installed in the correct positions, and corrective action if necessary. This AD is prompted by reports that lower guide fittings for the forward doors were found installed in the wrong positions at frames 14 and 16A. We are issuing this AD to prevent difficulty opening the forward doors, which could impede an emergency evacuation and result in injury to passengers or crewmembers.

Why this record is shown

Source: Federal Register annual FAA metadata. Acquired 2026-09-03T22:23:17.300228+00:00. The title, summary and date are source facts.

Source revision
federal_register_ad_metadata_2005-5d43d153038ee1c1
Source row
results[107]
Raw source SHA-256
5d43d153038ee1c1c214f5c3688e38e25e37b832227fe65d52f7420a65ee20f2

Final-rule publication

Recorded publication clauses

AD identifier printed in this edition
2005-05-16
Effective date printed in this edition
2005-04-18
Read 11 complete recorded clauses
Effective Date
Effective Date

    (a) This AD becomes effective April 18, 2005.

Exact source excerpt. Text positions 6140–6207, end exclusive, in the original decoded publication. SHA-256: f390f967c3bd7f0251cb52e40aef8e2f484df73509a4543095a9f5d6b6a15a5c

Affected ADs
Affected ADs

    (b) None.

Exact source excerpt. Text positions 6207–6236, end exclusive, in the original decoded publication. SHA-256: 027fbc44617399472b6ac4741da3aee18448654374228bcf4fe3f01df6b1539b

Applicability wording · Applicability
Applicability

    (c) This AD applies to Airbus Model A300 B4-622R airplanes, 
serial numbers 0797 and 0836 inclusive; and Model A300 F4-622R 
airplanes, serial numbers 0805 through 0828 inclusive; certificated 
in any category.

Exact source excerpt. Text positions 6236–6467, end exclusive, in the original decoded publication. SHA-256: 291edc48bd4fc72aff653d683bcef0fcc204d2cb26660b453a84ca9b38559a87

Unsafe Condition
Unsafe Condition

    (d) This AD was prompted by reports that lower guide fittings 
for the forward doors were found installed in the wrong positions at 
frames 14 and 16A. We are issuing this AD to prevent difficulty 
opening the forward doors, which could impede an emergency 
evacuation and result in injury to passengers or crewmembers.

Exact source excerpt. Text positions 6467–6810, end exclusive, in the original decoded publication. SHA-256: 53aa812e0a89878a00b766e2def63fd2975ad62f00d415605b0207e9b0444936

Compliance
Compliance

    (e) You are responsible for having the actions required by this 
AD performed within the compliance times specified, unless the 
actions have already been done.

Exact source excerpt. Text positions 6810–6988, end exclusive, in the original decoded publication. SHA-256: 64a7a1579f37f56eafecd0aeb3c528e7c89f6292ed0cb53091423917642d5847

Inspection and Corrective Action
Inspection and Corrective Action

    (f) Within 600 flight hours after the effective date of this AD, 
do a one-time detailed inspection to determine if lower guide 
fittings for the forward doors are installed in the correct 
positions, in accordance with the Accomplishment Instructions of 
Airbus Service Bulletin A300-53-6140, Revision 01, dated November 
24, 2003.
    (1) If the lower guide fittings are installed in the correct 
positions: No further action is required by this AD.
    (2) If any lower guide fitting is not installed in the correct 
position: Before further flight, re-install the lower guide fitting 
in the correct position, or replace the lower guide fitting with a 
new, improved guide fitting, as applicable, in accordance with the 
service bulletin.

    Note 1: For the purposes of this AD, a detailed inspection is: 
``An intensive examination of a specific item, installation, or 
assembly to detect damage, failure, or irregularity. Available 
lighting is normally supplemented with a direct source of good 
lighting at an intensity deemed appropriate. Inspection aids such as 
mirror, magnifying lenses, etc., may be necessary. Surface cleaning 
and elaborate procedures may be required.''

Exact source excerpt. Text positions 6988–8215, end exclusive, in the original decoded publication. SHA-256: 6321a2370c38c51e741550077d0f8530e5facd9d2692724c7f938c7cf50fa940

Actions Accomplished In Accordance With Previous Issue of Service Bulletin
Actions Accomplished In Accordance With Previous Issue of Service 
Bulletin

    (g) Inspections and corrective actions accomplished before the 
effective date of this AD in accordance with Airbus Service Bulletin 
A300-53-6140, dated June 12, 2003, are considered acceptable for 
compliance with the corresponding actions specified in this AD.

Exact source excerpt. Text positions 8215–8561, end exclusive, in the original decoded publication. SHA-256: f62d42bf270efb46350b9936ffb97370f8bd30513371911bfcae44b83f9ea827

No Reporting Requirement
No Reporting Requirement

    (h) The Accomplishment Instructions of Airbus Service Bulletin 
A300-53-6140, Revision 01, dated November 24, 2003, describe 
procedures for reporting inspection findings to the manufacturer. 
This AD does not require this reporting.

Exact source excerpt. Text positions 8561–8826, end exclusive, in the original decoded publication. SHA-256: 00b61014d4480fe955e7ee1307fc8668925c4b2d7f76b3ce5241810bc20f9578

Alternative Methods of Compliance (AMOCs)
Alternative Methods of Compliance (AMOCs)

    (i) The Manager, International Branch, ANM-116, Transport 
Airplane Directorate, FAA, has the authority to approve AMOCs for 
this AD, if requested in accordance with the procedures found in 14 
CFR 39.19.

Exact source excerpt. Text positions 8826–9080, end exclusive, in the original decoded publication. SHA-256: b6ab6b0f246045bba5ba60b95f93a07e33abbbf0018f2163c3bb312358ce2da4

Related Information
Related Information

    (j) French airworthiness directive 2003-292(B), dated August 6, 
2003, also addresses the subject of this AD.

Exact source excerpt. Text positions 9080–9216, end exclusive, in the original decoded publication. SHA-256: f17e4d1150fd93e74b26a916f7a19815a233e0d0b89f6839c99e4541cdfe9115

Material Incorporated by Reference
Material Incorporated by Reference

    (k) You must use Airbus Service Bulletin A300-53-6140, Revision 
01, dated November 24, 2003, excluding Appendix 01, to perform the 
actions that are required by this AD, unless the AD specifies 
otherwise. The Director of the Federal Register approves the 
incorporation by reference of this document in accordance with 5 
U.S.C. 552(a) and 1 CFR part 51. For copies of the service 
information, contact Airbus, 1 Rond Point Maurice Bellonte, 31707 
Blagnac Cedex, France. For information on the availability of this 
material at the National Archives and Records Administration (NARA), 
call (202) 741-6030, or go to http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.
    You may view the AD docket at the Docket Management Facility, 
U.S. Department of Transportation, 400 Seventh Street SW., room PL-
401, Nassif Building, Washington, DC.

Exact source excerpt. Text positions 9216–10137, end exclusive, in the original decoded publication. SHA-256: 672078b34b79e887bce43702efcf23239fd93ecd1838e468464a3bb6b8b14ceb

No replacement link has been established from this edition. The complete historical rule chain and current legal effect remain unknown.

Find all recorded historical references to AD 2005-05-16 · 0 printed reference observations in this pinned collection.

These are observations from one dated publication. Current legal status is unknown; aircraft applicability, installed configuration, compliance and burden require separate evidence. Missing or unparsed conditions remain unknown.

Why these observations are shown

They were extracted offline from the same immutable official HTML source as the complete recorded text. The dated source wording, original text coordinates and exact quote digests are retained. PDF/text agreement and current regulatory effect have not been qualified.

Observation revision: whole-ad-publication-clause-observations-1.0.1. Text SHA-256: fcaf28890fe497b3e9c5e4f40ff15970cd8e036fb2efcbe6451f6230e3eb86bb. Source manifest: b4a70db4102bf24395468da3b7a5039470296b0b60ae34be539417a59d8509b2.

Official source · 2005-03-14

Publication text

This is the complete recorded text of this dated publication.

Current legal effect is unknown. Aircraft applicability, installed configuration and compliance require separate evidence. PDF/text agreement has not been evaluated.

Read the complete official publication text
[Federal Register Volume 70, Number 48 (Monday, March 14, 2005)]
[Rules and Regulations]
[Pages 12402-12403]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 05-4828]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2004-19542; Directorate Identifier 2003-NM-282-AD; 
Amendment 39-14005; AD 2005-05-16]
RIN 2120-AA64


Airworthiness Directives; Airbus Model A300 B4-622R and A300 F4-
622R Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: The FAA is adopting a new airworthiness directive (AD) for 
certain Airbus Model A300 B4-622R and A300 F4-622R airplanes. This AD 
requires doing a one-time inspection to determine if lower guide 
fittings for the forward doors are installed in the correct positions, 
and corrective action if necessary. This AD is prompted by reports that 
lower guide fittings for the forward doors were found installed in the 
wrong positions at frames 14 and 16A. We are issuing this AD to prevent 
difficulty opening the forward doors, which could impede an emergency 
evacuation and result in injury to passengers or crewmembers.

DATES: This AD becomes effective April 18, 2005.
    The incorporation by reference of a certain publication listed in 
the AD is approved by the Director of the Federal Register as of April 
18, 2005.

ADDRESSES: For service information identified in this AD, contact 
Airbus, 1 Rond Point Maurice Bellonte, 31707 Blagnac Cedex, France.
    Docket: The AD docket contains the proposed AD, comments, and any 
final disposition. You can examine the AD docket on the Internet at 
http://dms.dot.gov, or in person at the Docket Management Facility 
office between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The Docket Management Facility office (telephone (800) 647-
5227) is located on the plaza level of the Nassif Building at the U.S. 
Department of Transportation, 400 Seventh Street, SW., room PL-401, 
Washington, DC. This docket number is FAA-2004-19542; the directorate 
identifier for this docket is 2004-NM-282-AD.

FOR FURTHER INFORMATION CONTACT: Dan Rodina, Aerospace Engineer, 
International Branch, ANM-116, FAA, Transport Airplane Directorate, 
1601 Lind Avenue, SW., Renton, Washington 98055-4056; telephone (425) 
227-2125; fax (425) 227-1149.

SUPPLEMENTARY INFORMATION: The FAA proposed to amend 14 CFR Part 39 
with an AD for certain Airbus Model A300 B4-622R and A300 F4-622R 
airplanes. That action, published in the Federal Register on November 
5, 2004 (69 FR 64504), proposed to require doing a one-time inspection 
to determine if lower guide fittings for the forward doors are 
installed in the correct positions, and corrective action if necessary.

Comments

    We provided the public the opportunity to participate in the 
development of this AD. No comments have been submitted on the proposed 
AD or on the determination of the cost to the public.

Conclusion

    We have carefully reviewed the available data and determined that 
air safety and the public interest require adopting the AD as proposed.

Costs of Compliance

    This AD will affect about 25 airplanes of U.S. registry. The 
required actions

[[Page 12403]]

will take about 2 work hours per airplane, at an average labor rate of 
$65 per work hour. Based on these figures, the estimated cost of the AD 
for U.S. operators is $3,250, or $130 per airplane.

Authority for this Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, Section 106, describes the 
authority of the FAA Administrator. Subtitle VII, Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701, ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We have determined that this AD will not have federalism 
implications under Executive Order 13132. This AD will not have a 
substantial direct effect on the States, on the relationship between 
the national government and the States, or on the distribution of power 
and responsibilities among the various levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866;
    (2) Is not a ``significant rule'' under DOT Regulatory Policies and 
Procedures (44 FR 11034, February 26, 1979); and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this AD. See the ADDRESSES section for a location to 
examine the regulatory evaluation.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

0
Accordingly, under the authority delegated to me by the Administrator, 
the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

2005-05-16 Airbus: Amendment 39-14005. Docket No. FAA-2004-19542; 
Directorate Identifier 2003-NM-282-AD.

Effective Date

    (a) This AD becomes effective April 18, 2005.

Affected ADs

    (b) None.

Applicability

    (c) This AD applies to Airbus Model A300 B4-622R airplanes, 
serial numbers 0797 and 0836 inclusive; and Model A300 F4-622R 
airplanes, serial numbers 0805 through 0828 inclusive; certificated 
in any category.

Unsafe Condition

    (d) This AD was prompted by reports that lower guide fittings 
for the forward doors were found installed in the wrong positions at 
frames 14 and 16A. We are issuing this AD to prevent difficulty 
opening the forward doors, which could impede an emergency 
evacuation and result in injury to passengers or crewmembers.

Compliance

    (e) You are responsible for having the actions required by this 
AD performed within the compliance times specified, unless the 
actions have already been done.

Inspection and Corrective Action

    (f) Within 600 flight hours after the effective date of this AD, 
do a one-time detailed inspection to determine if lower guide 
fittings for the forward doors are installed in the correct 
positions, in accordance with the Accomplishment Instructions of 
Airbus Service Bulletin A300-53-6140, Revision 01, dated November 
24, 2003.
    (1) If the lower guide fittings are installed in the correct 
positions: No further action is required by this AD.
    (2) If any lower guide fitting is not installed in the correct 
position: Before further flight, re-install the lower guide fitting 
in the correct position, or replace the lower guide fitting with a 
new, improved guide fitting, as applicable, in accordance with the 
service bulletin.

    Note 1: For the purposes of this AD, a detailed inspection is: 
``An intensive examination of a specific item, installation, or 
assembly to detect damage, failure, or irregularity. Available 
lighting is normally supplemented with a direct source of good 
lighting at an intensity deemed appropriate. Inspection aids such as 
mirror, magnifying lenses, etc., may be necessary. Surface cleaning 
and elaborate procedures may be required.''

Actions Accomplished In Accordance With Previous Issue of Service 
Bulletin

    (g) Inspections and corrective actions accomplished before the 
effective date of this AD in accordance with Airbus Service Bulletin 
A300-53-6140, dated June 12, 2003, are considered acceptable for 
compliance with the corresponding actions specified in this AD.

No Reporting Requirement

    (h) The Accomplishment Instructions of Airbus Service Bulletin 
A300-53-6140, Revision 01, dated November 24, 2003, describe 
procedures for reporting inspection findings to the manufacturer. 
This AD does not require this reporting.

Alternative Methods of Compliance (AMOCs)

    (i) The Manager, International Branch, ANM-116, Transport 
Airplane Directorate, FAA, has the authority to approve AMOCs for 
this AD, if requested in accordance with the procedures found in 14 
CFR 39.19.

Related Information

    (j) French airworthiness directive 2003-292(B), dated August 6, 
2003, also addresses the subject of this AD.

Material Incorporated by Reference

    (k) You must use Airbus Service Bulletin A300-53-6140, Revision 
01, dated November 24, 2003, excluding Appendix 01, to perform the 
actions that are required by this AD, unless the AD specifies 
otherwise. The Director of the Federal Register approves the 
incorporation by reference of this document in accordance with 5 
U.S.C. 552(a) and 1 CFR part 51. For copies of the service 
information, contact Airbus, 1 Rond Point Maurice Bellonte, 31707 
Blagnac Cedex, France. For information on the availability of this 
material at the National Archives and Records Administration (NARA), 
call (202) 741-6030, or go to http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.
    You may view the AD docket at the Docket Management Facility, 
U.S. Department of Transportation, 400 Seventh Street SW., room PL-
401, Nassif Building, Washington, DC.

    Issued in Renton, Washington, on March 2, 2005.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 05-4828 Filed 3-11-05; 8:45 am]
BILLING CODE 4910-13-P


Why this text is shown

The complete text was extracted from the official GovInfo HTML edition for this publication. Acquired 2026-10-09T03:58:09.612987+00:00. Text extraction preserves the recorded source wording; it does not determine current requirements.

Open the captured official edition

Source SHA-256
ccee8f191c82aa8cce1d3ad5c1af55878a6884a3dcffb4fc793f04c3a18bb525
Text SHA-256
fcaf28890fe497b3e9c5e4f40ff15970cd8e036fb2efcbe6451f6230e3eb86bb

Return to the full metadata catalog · Search complete publication text · Explore retained publication text and evidence

Coverage and limits

These are dated publication metadata, recorded clauses and literal source observations. Word, model-label, header and reference matches do not establish current legal effect, manufacturer/model identity, aircraft applicability, installed configuration or compliance.

The collection uses 33 explicit annual source snapshots. Source captures and operative-text qualifications have separate states. Missing information remains unknown.