Airworthiness Directives; British Aerospace Regional Aircraft Model HP.137 Jetstream Mk.1, Jetstream Series 200, Jetstream Series 3101, and Jetstream Model 3201 Airplanes

[Federal Register Volume 72, Number 98 (Tuesday, May 22, 2007)]
[Rules and Regulations]
[Pages 28587-28589]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 07-2522]



========================================================================
Rules and Regulations
                                                Federal Register
________________________________________________________________________

This section of the FEDERAL REGISTER contains regulatory documents 
having general applicability and legal effect, most of which are keyed 
to and codified in the Code of Federal Regulations, which is published 
under 50 titles pursuant to 44 U.S.C. 1510.

The Code of Federal Regulations is sold by the Superintendent of Documents. 
Prices of new books are listed in the first FEDERAL REGISTER issue of each 
week.

========================================================================


Federal Register / Vol. 72, No. 98 / Tuesday, May 22, 2007 / Rules 
and Regulations

[[Page 28587]]



DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2007-27213 Directorate Identifier 2007-CE-012-AD; 
Amendment 39-15055; AD 2007-10-14]
RIN 2120-AA64


Airworthiness Directives; British Aerospace Regional Aircraft 
Model HP.137 Jetstream Mk.1, Jetstream Series 200, Jetstream Series 
3101, and Jetstream Model 3201 Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We are superseding an existing airworthiness directive (AD) 
for the products listed above. This AD results from mandatory 
continuing airworthiness information (MCAI) issued by an aviation 
authority of another country to identify and correct an unsafe 
condition on an aviation product. The MCAI describes the unsafe 
condition as:

    Cracking has been found in the nose landing gear steering jack 
piston rod adjacent to the eye-end. This was caused by the 
application of excessive tightening torque applied to the eye-end 
whilst being assembled during component overhaul. Failure of the 
steering jack piston during operation will result in loss of nose 
wheel steering, which may lead to loss of directional control during 
critical phases of take-off and landing.

    We are issuing this AD to require actions to correct the unsafe 
condition on these products.

DATES: This AD becomes effective June 26, 2007.
    On June 26, 2007, the Director of the Federal Register approved the 
incorporation by reference of APPH Ltd. Service Bulletin 32-76, 
Revision 1, dated August 2003, as referenced in BAE Systems British 
Aerospace Jetstream Series 3100 & 3200 Service Bulletin 32-JA030644, 
Original Issue: October 6, 2003, listed in this AD.
    As of May 22, 2003 (68 FR 16195, April 3, 2003), the Director of 
the Federal Register approved the incorporation by reference of APPH 
Ltd. Service Bulletin 32-76, pages 1, 2, and 4 through 7, dated October 
2002; and page 3, Erratum 1, dated November 2002, as referenced in BAE 
Systems British Aerospace Jetstream Mandatory Service Bulletin 32-
JA020741, Original Issue: November 2, 2002, listed in this AD.

ADDRESSES: You may examine the AD docket on the Internet at http://dms.dot.gov or in person at the Docket Management Facility, U.S. 
Department of Transportation, 400 Seventh Street, SW., Nassif Building, 
Room PL-401, Washington, DC.

FOR FURTHER INFORMATION CONTACT: Taylor Martin, Aerospace Engineer, 
FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, 
Missouri 64106; telephone: (816) 329-4138; fax: (816) 329-4090.

SUPPLEMENTARY INFORMATION:

Streamlined Issuance of AD

    The FAA is implementing a new process for streamlining the issuance 
of ADs related to MCAI. The streamlined process will allow us to adopt 
MCAI safety requirements in a more efficient manner and will reduce 
safety risks to the public. This process continues to follow all FAA AD 
issuance processes to meet legal, economic, Administrative Procedure 
Act, and Federal Register requirements. We also continue to meet our 
technical decision-making responsibilities to identify and correct 
unsafe conditions on U.S.-certificated products.
    This AD references the MCAI and related service information that we 
considered in forming the engineering basis to correct the unsafe 
condition. The AD contains text copied from the MCAI and for this 
reason might not follow our plain language principles.

Discussion

    We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR 
part 39 to include an AD that would apply to the specified products. 
That NPRM was published in the Federal Register on March 15, 2007 (72 
FR 12133) and proposed to supersede AD 2003-07-06, Amendment 39-13102 
(68 FR 16195, April 3, 2003). The NPRM proposed to correct an unsafe 
condition for the specified products. The MCAI states:

    Cracking has been found in the nose landing gear steering jack 
piston rod adjacent to the eye-end. This was caused by the 
application of excessive tightening torque applied to the eye-end 
whilst being assembled during component overhaul. Failure of the 
steering jack piston during operation will result in loss of nose 
wheel steering, which may lead to loss of directional control during 
critical phases of take-off and landing.
    The inspections and any required rectification actions detailed 
in BAe Systems Service Bulletin 32-JA030644 and associated APPH 
Service Bulletin 32-76 Revision 1 are required to be performed to 
ensure continued airworthiness of the aircraft.

Comments

    We gave the public the opportunity to participate in developing 
this AD. We received no comments on the NPRM or on the determination of 
the cost to the public.

Conclusion

    We reviewed the available data and determined that air safety and 
the public interest require adopting the AD as proposed.

Differences Between This AD and the MCAI or Service Information

    We have reviewed the MCAI and related service information and, in 
general, agree with their substance. But we might have found it 
necessary to use different words from those in the MCAI to ensure the 
AD is clear for U.S. operators and is enforceable. In making these 
changes, we do not intend to differ substantively from the information 
provided in the MCAI and related service information.
    We might also have required different actions in this AD from those 
in the MCAI in order to follow FAA policies. Any such differences are 
highlighted in a NOTE within the AD.

Costs of Compliance

    We estimate that this AD will affect 190 products of U.S. registry. 
We also estimate that it will take about 2 work-hours per product to 
comply with basic requirements of this AD. The average labor rate is 
$80 per work-hour. Based

[[Page 28588]]

on these figures, we estimate the cost of this AD to the U.S. operators 
to be $30,400, or $160 per product.
    In addition, we estimate that any necessary follow-on actions will 
take about 8 work-hours and require parts costing $5,300, for a cost of 
$5,940 per product. We have no way of determining the number of 
products that may need these actions.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this AD will not have federalism implications 
under Executive Order 13132. This AD will not have a substantial direct 
effect on the States, on the relationship between the national 
government and the States, or on the distribution of power and 
responsibilities among the various levels of government.
    For the reasons discussed above, I certify this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866;
    (2) Is not a ``significant rule'' under DOT Regulatory Policies and 
Procedures (44 FR 11034, February 26, 1979); and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this AD and placed it in the AD Docket.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://dms.dot.gov; or in person at the Docket Management Facility between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD 
docket contains the NPRM, the regulatory evaluation, any comments 
received, and other information. The street address for the Docket 
Office (telephone (800) 647-5227) is in the ADDRESSES section. Comments 
will be available in the AD docket shortly after receipt.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

0
Accordingly, under the authority delegated to me by the Administrator, 
the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]


0
2. The FAA amends Sec.  39.13 by removing AD 2003-07-06, Amendment 39-
13102 (68 FR 16195, April 3, 2003) and adding the following new AD:

2007-10-14 British Aerospace Regional Aircraft: Amendment 39-15055; 
Docket No. FAA-2007-27213; Directorate Identifier 2007-CE-012-AD.

Effective Date

    (a) This airworthiness directive (AD) becomes effective June 26, 
2007.

Affected ADs

    (b) Supersedes AD 2003-07-06, Amendment 39-13102.

Applicability

    (c) This AD applies to Model HP.137 Jetstream Mk.1, Jetstream 
Series 200, Jetstream Series 3101, and Jetstream Model 3201 
airplanes, all serial numbers, certificated in any category.

Subject

    (d) Air Transport Association of America (ATA) Code 32: Landing 
Gear.

Reason

    (e) The mandatory continuing airworthiness information (MCAI) 
states:

    Cracking has been found in the nose landing gear steering jack 
piston rod adjacent to the eye-end. This was caused by the 
application of excessive tightening torque applied to the eye-end 
whilst being assembled during component overhaul. Failure of the 
steering jack piston during operation will result in loss of nose 
wheel steering, which may lead to loss of directional control during 
critical phases of take-off and landing.
    The inspections and any required rectification actions detailed 
in BAe Systems Service Bulletin 32-JA030644 and associated APPH 
Service Bulletin 32-76 Revision 1 are required to be performed to 
ensure continued airworthiness of the aircraft.

Retained Requirements of AD 2003-07-06

    (f) Unless already done, do the following actions in accordance 
with the procedures in APPH Ltd. Service Bulletin 32-76 (pages 1, 2, 
and 4 through 7, dated October 2002; and page 3, Erratum 1, dated 
November 2002), as referenced in BAE Systems British Aerospace 
Jetstream Mandatory Service Bulletin 32-JA020741, Original Issue: 
November 2, 2002; or APPH Ltd. Service Bulletin 32-76, Revision 1, 
dated August 2003, as referenced in BAE Systems British Aerospace 
Jetstream Series 3100 & 3200 Service Bulletin 32-JA030644, dated 
October 6, 2003.
    (1) Inspect the steering jack piston rod for cracks within the 
next 90 days or 200 ground-air-ground (GAG) cycles after May 22, 
2003 (the effective date of AD 2003-07-06), whichever occurs first.
    (2) If cracks are found, replace the cracked steering jack 
piston rod. Install the new steering jack piston rod using a torque 
setting of 175 lbf (pound force) inch or 20 Nm (Newton meters) when 
tightening the end fitting and stop bolt before further flight after 
the inspection required in paragraph (f)(1) of this AD.
    (3) If no cracks are found, determine the torque setting of the 
steering jack piston rod end fitting and stop bolt before further 
flight after the inspection required in paragraph (f)(1) of this AD.

New Requirements of This AD: Actions and Compliance

    (g) Unless already done, do the following actions:
    (1) Within 90 days after June 26, 2007 (the effective date of 
this AD), recalculate the safe life of the steering jack piston rod 
and re-torque the piston rod eye-end in accordance with APPH Ltd. 
Service Bulletin 32-76, Revision 1, dated August 2003, as referenced 
in paragraph 2, Part 2 of BAE Systems British Aerospace Jetstream 
Series 3100 & 3200 Service Bulletin 32-JA030644, dated October 6, 
2003.
    (2) If the piston rod is found unserviceable when inspected in 
accordance with APPH Ltd. Service Bulletin 32-76, Revision 1, dated 
August 2003, as referenced in paragraph 2, Part 2 of BAE Systems 
British Aerospace Jetstream Series 3100 & 3200 Service Bulletin 32-
JA030644, dated October 6, 2003, before further flight remove the 
steering jack and replace with a serviceable unit.
    (3) As of June 26, 2007 (the effective date of this AD), before 
a steering jack piston rod is installed, it must be inspected and 
the safe life determined in accordance APPH Ltd. Service Bulletin 
32-76, Revision 1, dated August 2003, as referenced in paragraph 2 
of BAE Systems British Aerospace Jetstream Series 3100 & 3200 
Service Bulletin 32-JA030644, dated October 6, 2003.

FAA AD Differences

    Note: This AD differs from the MCAI and/or service information 
as follows: No differences.


[[Page 28589]]



Other FAA AD Provisions

    (h) The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
Standards Staff, FAA, has the authority to approve AMOCs for this 
AD, if requested using the procedures found in 14 CFR 39.19. Send 
information to ATTN: Taylor Martin, Aerospace Engineer, FAA, Small 
Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 
64106; telephone: (816) 329-4138; fax: (816) 329-4090. Before using 
any approved AMOC on any airplane to which the AMOC applies, notify 
your appropriate principal inspector (PI) in the FAA Flight 
Standards District Office (FSDO), or lacking a PI, your local FSDO.
    (2) AMOCs approved for AD 2003-07-06 are not approved for this 
AD.
    (3) Airworthy Product: For any requirement in this AD to obtain 
corrective actions from a manufacturer or other source, use these 
actions if they are FAA-approved. Corrective actions are considered 
FAA-approved if they are approved by the State of Design Authority 
(or their delegated agent). You are required to assure the product 
is airworthy before it is returned to service.
    (4) Reporting Requirements: For any reporting requirement in 
this AD, under the provisions of the Paperwork Reduction Act (44 
U.S.C. 3501 et seq.), the Office of Management and Budget (OMB) has 
approved the information collection requirements and has assigned 
OMB Control Number 2120-0056.

Related Information

    (i) Refer to MCAI Civil Aviation Authority AD No. G-2004-0029, 
dated December 20, 2004; BAE Systems British Aerospace Jetstream 
Series 3100 & 3200 Service Bulletin 32-JA030644, dated October 6, 
2003; BAE Systems British Aerospace Jetstream Mandatory Service 
Bulletin 32-JA020741, Original Issue: November 2, 2002; APPH Ltd. 
Service Bulletin 32-76, Revision 1, dated August 2003; and APPH Ltd. 
Service Bulletin 32-76, pages 1, 2, and 4 through 7, dated October 
2002; and page 3, Erratum 1, dated November 2002, for related 
information.

Material Incorporated by Reference

    (j) You must use APPH Ltd. Service Bulletin 32-76, Revision 1, 
dated August 2003; as referenced in BAE Systems British Aerospace 
Jetstream Series 3100 & 3200 Service Bulletin 32-JA030644, dated 
October 6, 2003; and APPH Ltd. Service Bulletin 32-76, pages 1, 2, 
and 4 through 7, dated October 2002; and page 3, Erratum 1, dated 
November 2002; as referenced in BAE Systems British Aerospace 
Jetstream Mandatory Service Bulletin 32-JA020741, Original Issue: 
November 2, 2002; to do the actions required by this AD, unless the 
AD specifies otherwise.
    (1) The Director of the Federal Register approved the 
incorporation by reference of APPH Ltd. Service Bulletin 32-76, 
Revision 1, dated August 2003; as referenced in BAE Systems British 
Aerospace Jetstream Series 3100 & 3200 Service Bulletin 32-JA030644, 
dated October 6, 2003, under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) On May 22, 2003 (68 FR 16195, April 3, 2003), the Director 
of the Federal Register approved the incorporation by reference of 
APPH Ltd. Service Bulletin 32-76, pages 1, 2, and 4 through 7, dated 
October 2002; and page 3, Erratum 1, dated November 2002, as 
referenced in BAE Systems British Aerospace Jetstream Mandatory 
Service Bulletin 32-JA020741, Original Issue: November 2, 2002.
    (3) For service information identified in this AD, contact BAE 
Systems, Prestwick International Airport, Ayshire, KA9 2RW, 
Scotland; telephone: (01292) 675207; fax: (01292) 675704.
    (4) You may review copies at the FAA, Central Region, Office of 
the Regional Counsel, 901 Locust, Room 506, Kansas City, Missouri 
64106; or at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued in Kansas City, Missouri, on May 9, 2007.
Charles L. Smalley,
Acting Manager, Small Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 07-2522 Filed 5-21-07; 8:45 am]
BILLING CODE 4910-13-P

The complete text was extracted from the official GovInfo HTML edition for this publication. Acquired 2026-10-09T03:38:32.676962+00:00. Text extraction preserves the recorded source wording; it does not determine current requirements.

Open the captured official edition

Source SHA-256

af63b20f929e33b804cd3892f6caf7efa3da59e47a8b02b87069cd935f8cbc7f

Text SHA-256

50f2b8832c674440bd4a0f7666048ce64eb9d8c7104b4e9694cf06245d674862