Airworthiness Directives; Airbus Model A330-223, -321, -322, and -323 Airplanes

[Federal Register Volume 75, Number 159 (Wednesday, August 18, 2010)]
[Rules and Regulations]
[Pages 50867-50869]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2010-19839]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2010-0278; Directorate Identifier 2009-NM-255-AD; 
Amendment 39-16399; AD 2010-17-07]
RIN 2120-AA64


Airworthiness Directives; Airbus Model A330-223, -321, -322, and 
-323 Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for the 
products listed above. This AD results from mandatory continuing 
airworthiness information (MCAI) originated by an aviation authority of 
another country to identify and correct an unsafe condition on an 
aviation product. The MCAI describes the unsafe condition as:

    During accomplishment of Damage Tolerant--Airworthiness 
Limitation Item task 712106-01-01 from A330 ALS Part 2, an A330 
operator found a Fluorescent Penetrant Inspection (FPI) indication 
in the head of the shank filet radius in one of the Pratt & Whitney 
(PW) forward (FWD) engine mount pylon bolts.
* * * * *
    Dual-bolt fractures could lead to inability for mount assembly 
to sustain loads which may lead to an engine mount failure and 
consequently to engine separation from the aeroplane during flight, 
which would constitute an unsafe condition.
* * * * *
    We are issuing this AD to require actions to correct the unsafe 
condition on these products.

DATES: This AD becomes effective September 22, 2010.
    The Director of the Federal Register approved the incorporation by 
reference of certain publications listed in this AD as of September 22, 
2010.

ADDRESSES: You may examine the AD docket on the Internet at http://www.regulations.gov or in person at the U.S. Department of 
Transportation, Docket Operations, M-30, West Building Ground Floor, 
Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC.

FOR FURTHER INFORMATION CONTACT: Vladimir Ulyanov, Aerospace Engineer, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425) 
227-1138; fax (425) 227-1149.

SUPPLEMENTARY INFORMATION:

Discussion

    We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR 
part 39 to include an AD that would apply to the specified products. 
That NPRM was published in the Federal Register on April 2, 2010 (75 FR 
16696). That NPRM proposed to correct an unsafe condition for the 
specified products. The MCAI states:

    During accomplishment of Damage Tolerant--Airworthiness 
Limitation Item task 712106-01-01 from A330 ALS Part 2, an A330 
operator found a Fluorescent Penetrant Inspection (FPI) indication 
in the head of the shank filet radius in one of the Pratt & Whitney 
(PW) forward (FWD) engine mount pylon bolts.
    Investigation has confirmed that this FPI indication was due to 
a quality manufacturing process issue which led to a bolt non-
conformance and is also applicable to aftward (AFT) mount pylon 
bolts.
    Dual-bolt fractures could lead to inability for mount assembly 
to sustain loads which may lead to an engine mount failure and 
consequently to engine separation from the aeroplane during flight, 
which would constitute an unsafe condition.
    This AD requires a one time detailed visual inspection of the 
FWD and AFT mount pylon bolts on all A330 aeroplanes fitted with PW 
engines (8 bolts per engine) and replacement of any affected bolt.

You may obtain further information by examining the MCAI in the AD 
docket.

Comments

    We gave the public the opportunity to participate in developing 
this AD. We considered the comments received.

Requests To Refer to the Latest Pratt & Whitney Service Information

    Delta Airlines and Pratt & Whitney--Cheshire Engine Center request 
that we revise the NPRM to refer to Pratt & Whitney Service Bulletin 
PW4G-100-71-35, Revision 1, dated December 4, 2009, for determining 
suspect bolts, rather than Pratt & Whitney Service Bulletin PW4G-100-
71-35, dated March 14, 2008, which was referenced in the NPRM as the 
appropriate source for determining suspect bolts. The

[[Page 50868]]

commenters state that Pratt & Whitney Service Bulletin PW4G-100-71-35, 
Revision 1, dated December 4, 2009, corrected suspect bolt serial 
numbers, and the serial number range of suspect bolts was reduced.
    We agree with the requests. Since fewer parts are listed and no 
parts are added in Pratt & Whitney Service Bulletin PW4G-100-71-35, 
Revision 1, dated December 4, 2009, we have revised paragraph (h) of 
this AD to refer to Pratt & Whitney Service Bulletin PW4G-100-71-35, 
Revision 1, dated December 4, 2009, as the appropriate source for 
determining suspect bolts. We have also revised paragraph (h) of this 
AD to provide credit to operators that used Pratt & Whitney Service 
Bulletin PW4G-100-71-35, dated March 14, 2008, to determine suspect 
bolts before the effective date of this AD.

Conclusion

    We reviewed the available data, including the comments received, 
and determined that air safety and the public interest require adopting 
the AD with the changes described previously. We determined that these 
changes will not increase the economic burden on any operator or 
increase the scope of the AD.

Differences Between This AD and the MCAI or Service Information

    We have reviewed the MCAI and related service information and, in 
general, agree with their substance. But we might have found it 
necessary to use different words from those in the MCAI to ensure the 
AD is clear for U.S. operators and is enforceable. In making these 
changes, we do not intend to differ substantively from the information 
provided in the MCAI and related service information.
    We might also have required different actions in this AD from those 
in the MCAI in order to follow our FAA policies. Any such differences 
are highlighted in a Note within the AD.

Costs of Compliance

    We estimate that this AD will affect 41 products of U.S. registry. 
We also estimate that it will take about 7 work-hours per product to 
comply with the basic requirements of this AD. The average labor rate 
is $85 per work-hour. Required parts will cost about $16,672 per 
product. Where the service information lists required parts costs that 
are covered under warranty, we have assumed that there will be no 
charge for these parts. As we do not control warranty coverage for 
affected parties, some parties may incur costs higher than estimated 
here. Based on these figures, we estimate the cost of this AD to the 
U.S. operators to be $707,947, or $17,267 per product.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this AD will not have federalism implications 
under Executive Order 13132. This AD will not have a substantial direct 
effect on the States, on the relationship between the national 
government and the States, or on the distribution of power and 
responsibilities among the various levels of government.
    For the reasons discussed above, I certify this AD:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979); and
    3. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this AD and placed it in the AD docket.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Operations office 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains the NPRM, the regulatory evaluation, 
any comments received, and other information. The street address for 
the Docket Operations office (telephone (800) 647-5527) is in the 
ADDRESSES section. Comments will be available in the AD docket shortly 
after receipt.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

0
Accordingly, under the authority delegated to me by the Administrator, 
the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new AD:

2010-17-07 Airbus: Amendment 39-16399. Docket No. FAA-2010-0278; 
Directorate Identifier 2009-NM-255-AD.

Effective Date

    (a) This airworthiness directive (AD) becomes effective 
September 22, 2010.

Affected ADs

    (b) None.

Applicability

    (c) This AD applies to Airbus Model A330-223, -321, -322, and -
323 airplanes; certificated in any category; all manufacturer serial 
numbers.

Subject

    (d) Air Transport Association (ATA) of America Code 71: 
Powerplant.

Reason

    (e) The mandatory continuing airworthiness information (MCAI) 
states:
    During accomplishment of Damage Tolerant--Airworthiness 
Limitation Item task 712106-01-01 from A330 ALS Part 2, an A330 
operator found a Fluorescent Penetrant Inspection (FPI) indication 
in the head of the shank filet radius in one of the Pratt & Whitney 
(PW) forward (FWD) engine mount pylon bolts.
    Investigation has confirmed that this FPI indication was due to 
a quality manufacturing process issue which led to a bolt non-
conformance and is also applicable to aft ward (AFT) mount pylon 
bolts.
    Dual-bolt fractures could lead to inability for mount assembly 
to sustain loads which may lead to an engine mount failure and 
consequently to engine separation from the aeroplane during flight, 
which would constitute an unsafe condition.
    This AD requires a one time detailed visual inspection of the 
FWD and AFT mount pylon bolts on all A330 aeroplanes fitted with PW 
engines (8 bolts per engine) and replacement of any affected bolt.

Compliance

    (f) You are responsible for having the actions required by this 
AD performed within the compliance times specified, unless the 
actions have already been done.

[[Page 50869]]

Actions

    (g) Do a detailed inspection to determine the part number, 
serial number, and lot number of the forward and aft mount pylon 
bolts on both engines, in accordance with the Accomplishment 
Instructions of Airbus Mandatory Service Bulletin A330-71-3020, 
dated June 10, 2009. Inspect at the later of the times specified in 
paragraphs (g)(1) and (g)(2) of this AD.
    (1) Before the accumulation of 8,000 total flight cycles or 
24,000 total flight hours since first flight of the airplane, 
whichever occurs first.
    (2) Within 24 months after the effective date of this AD.
    (h) If the identified part number, serial number, or lot number 
corresponds to suspect bolts identified in Pratt & Whitney Service 
Bulletin PW4G-100-71-35, Revision 1, dated December 4, 2009, before 
further flight remove the affected bolt and replace with a 
serviceable bolt, in accordance with the Accomplishment Instructions 
of Airbus Mandatory Service Bulletin A330-71-3020, dated June 10, 
2009. Identifying part numbers, serial numbers or lot numbers before 
the effective date of this AD according to Pratt & Whitney Service 
Bulletin PW4G-100-71-35, dated March 14, 2008, is considered 
acceptable for compliance with the corresponding action specified in 
this AD.
    (i) If the bolt part number, serial number, or lot number is 
unreadable, before further flight, remove the affected bolt and 
replace with a serviceable bolt, in accordance with the 
Accomplishment Instructions of Airbus Mandatory Service Bulletin 
A330-71-3020, dated June 10, 2009.
    (j) As of the effective date of this AD, no person may install 
any forward or aft mount pylon bolt on any airplane, unless this 
bolt has been identified as a non-suspect bolt, in accordance with 
the Accomplishment Instructions of Airbus Mandatory Service Bulletin 
A330-71-3020, dated June 10, 2009.
    (k) Although Airbus Mandatory Service Bulletin A330-71-3020, 
dated June 10, 2009, specifies to submit certain information to the 
manufacturer, this AD does not include that requirement.

FAA AD Differences

    Note 1: This AD differs from the MCAI and/or service information 
as follows: Although the MCAI or service information tells you to 
submit information to the manufacturer, paragraph (k) of this AD 
specifies that such submittal is not required.

Other FAA AD Provisions

    (l) The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
has the authority to approve AMOCs for this AD, if requested using 
the procedures found in 14 CFR 39.19. Send information to ATTN: 
Vladimir Ulyanov, Aerospace Engineer, International Branch, ANM-116, 
Transport Airplane Directorate, FAA, 1601 Lind Avenue, SW., Renton, 
Washington 98057-3356; telephone (425) 227-1138; fax (425) 227-1149. 
Before using any approved AMOC on any airplane to which the AMOC 
applies, notify your principal maintenance inspector (PMI) or 
principal avionics inspector (PAI), as appropriate, or lacking a 
principal inspector, your local Flight Standards District Office. 
The AMOC approval letter must specifically reference this AD.
    (2) Airworthy Product: For any requirement in this AD to obtain 
corrective actions from a manufacturer or other source, use these 
actions if they are FAA-approved. Corrective actions are considered 
FAA-approved if they are approved by the State of Design Authority 
(or their delegated agent). You are required to assure the product 
is airworthy before it is returned to service.

Related Information

    (m) Refer to MCAI European Aviation Safety Agency Airworthiness 
Directive 2009-0240, dated November 5, 2009; Airbus Mandatory 
Service Bulletin A330-71-3020, dated June 10, 2009; and Pratt & 
Whitney Service Bulletin PW4G-100-71-35, Revision 1, dated December 
4, 2009; for related information.

Material Incorporated by Reference

    (n) You must use Airbus Mandatory Service Bulletin A330-71-3020, 
excluding Appendix 1, dated June 10, 2009; and Pratt & Whitney 
Service Bulletin PW4G-100-71-35, Revision 1, dated December 4, 2009; 
as applicable; to do the actions required by this AD, unless the AD 
specifies otherwise.
    (1) The Director of the Federal Register approved the 
incorporation by reference of this service information under 5 
U.S.C. 552(a) and 1 CFR part 51.
    (2) For service information identified in this AD, contact 
Airbus SAS--Airworthiness Office--EAL, 1 Rond Point Maurice 
Bellonte, 31707 Blagnac Cedex, France; telephone +33 5 61 93 36 96; 
fax +33 5 61 93 45 80; e-mail [email protected]; 
Internet http://www.airbus.com.
    (3) You may review copies of the service information at the FAA, 
Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, 
Washington. For information on the availability of this material at 
the FAA, call 425-227-1221.
    (4) You may also review copies of the service information that 
is incorporated by reference at the National Archives and Records 
Administration (NARA). For information on the availability of this 
material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.

    Issued in Renton, Washington, on August 4, 2010.
Stephen P. Boyd,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2010-19839 Filed 8-17-10; 8:45 am]
BILLING CODE 4910-13-P

The complete text was extracted from the official GovInfo HTML edition for this publication. Acquired 2026-10-09T03:14:11.444841+00:00. Text extraction preserves the recorded source wording; it does not determine current requirements.

Open the captured official edition

Source SHA-256

ea15e629bcd5c49d7515842fee467eb5b77a0c6b48e84e825707230114469b60

Text SHA-256

81c7ee60b3993cdd133851ed59a4185d0f205e6536d24e40deead3e6bbb36ed8