Published 2010-11-03 · Federal Register document 2010-27608
Airworthiness Directives; McCauley Propeller Systems Five-Blade Propeller Assemblies
Publication summary
We are superseding an existing airworthiness directive (AD) for the products listed above. That AD currently requires removing certain propeller hubs from service at new, reduced life limits and eddy current inspections (ECIs) of the propeller hub. This new AD requires removing certain propeller hubs from service before they exceed 6,000 hours time-since-new (TSN). This AD was prompted by a report of a crack in a propeller hub. We are issuing this AD to prevent cracked propeller hubs, which could cause failure of the propeller hub, blade separation, and loss of control of the airplane.
Why this record is shown
Source: Federal Register annual FAA metadata. Acquired 2026-09-03T22:23:33.146842+00:00. The title, summary and date are source facts.
- Source revision
- federal_register_ad_metadata_2010-a7267cd3a71dbd26
- Source row
- results[352]
- Raw source SHA-256
- a7267cd3a71dbd2645583c8a673df65e4a7fa9360a96e3be0de5b81f9d68c9a0
Final-rule publication
Recorded publication clauses
- AD identifier printed in this edition
- 2010-23-06
- Effective date printed in this edition
- 2010-12-08
Read 10 complete recorded clauses
Effective Date
Effective Date
(a) This airworthiness directive (AD) is effective December 8,
2010.
Exact source excerpt. Text positions 7238–7329, end exclusive, in the original decoded publication. SHA-256: b0324abecdc6b2f0e69225f422e595e6497d96b6bc72b9dd0bca38c452bad07e
Affected ADs
Affected ADs
(b) This AD supersedes AD 2005-24-08, Amendment 39-14388.
Exact source excerpt. Text positions 7329–7406, end exclusive, in the original decoded publication. SHA-256: 4f649d043dd3476bf30d2ef4771acb2e7e3c7de3ef79a2e24f92ca26e7c2b602
Applicability wording · Applicability
Applicability
(c) This AD applies to McCauley Propeller Systems propeller
assemblies, part numbers (P/Ns) B5JFR36C1101/114GCA-0, C5JFR36C1102/
L114GCA-0, B5JFR36C1103/114HCA-0, and C5JFR36C1104/L114HCA-0. These
propeller assemblies are installed on BAE Systems (Operations)
Limited Jetstream Model 4100 series airplanes.
Exact source excerpt. Text positions 7406–7736, end exclusive, in the original decoded publication. SHA-256: d3762d9446bdc8a5ede5bd25b1e001ed174f8e2e3b89bd100ed6b6e966a743a4
Unsafe Condition
Unsafe Condition
(d) This AD results from a report of a cracked propeller hub. We
are issuing this AD to prevent cracked propeller hubs, which could
cause failure of the propeller hub, blade separation, and loss of
control of the airplane.
Exact source excerpt. Text positions 7736–7985, end exclusive, in the original decoded publication. SHA-256: cecd2d443b612fa7b57526b9d5ed017c4c1a9228c91f51c3ecc895d94d988c18
Compliance
Compliance
(e) You are responsible for having the actions required by this
AD performed within the compliance times specified unless the
actions have already been done.
Exact source excerpt. Text positions 7985–8162, end exclusive, in the original decoded publication. SHA-256: 9b3c9e019fb507cf6548fcccdb7151b3e1278af7078c0a234a67c27b748f31df
Propeller Hub Reduced Life Limits
Propeller Hub Reduced Life Limits
(f) For any propeller assembly, P/N B5JFR36C1101/114GCA-0,
C5JFR36C1102/L114GCA-0, B5JFR36C1103/114HCA-0, or C5JFR36C1104/
L114HCA-0, with a hub that exceeds 6,000 hours time-since-new (TSN)
on the effective date of this AD, remove the propeller hub from
service within 250 hours time-in-service after the effective date of
this AD.
(g) For any propeller assembly, P/N B5JFR36C1101/114GCA-0,
C5JFR36C1102/L114GCA-0, B5JFR36C1103/114HCA-0, or C5JFR36C1104/
L114HCA-0, with a hub with fewer than 6,000 hours TSN, remove the
propeller hub from service not later than 6,000 hours TSN.
Exact source excerpt. Text positions 8162–8793, end exclusive, in the original decoded publication. SHA-256: 3abe7ba7a7513c211603b485714bbef3e4f243607423c0fb15bdb4e04238e827
Prohibition of Hubs Exceeding Life Limit
Prohibition of Hubs Exceeding Life Limit
(h) After the effective date of this AD, don't install any hub
removed from any propeller assembly that was removed by paragraphs
(f) or (g) of this AD into any propeller assembly.
[[Page 67615]]
Exact source excerpt. Text positions 8793–9039, end exclusive, in the original decoded publication. SHA-256: 197fcb851d44f562c1095424765ef20d09400048e0dd1a537f1ec8f69d25e5e1
Alternative Methods of Compliance
Alternative Methods of Compliance
(i) The Manager, Wichita Aircraft Certification Office, has the
authority to approve alternative methods of compliance for this AD
if requested using the procedures found in 14 CFR 39.19.
Exact source excerpt. Text positions 9039–9269, end exclusive, in the original decoded publication. SHA-256: 58b199882fa707d858af439b0dcd6a3adf1bb578a277a86f2f341763a35c827b
Related Information
Related Information
(j) Contact Jeff Janusz, Aerospace Engineer, Wichita Aircraft
Certification Office, FAA, Small Airplane Directorate, 1801 Airport
Road, Room 100, Wichita, KS 67209, telephone: (316) 946-4148; fax:
(316) 946-4107, for more information about this AD.
Exact source excerpt. Text positions 9269–9547, end exclusive, in the original decoded publication. SHA-256: aa6d716123dedc98be75435ff10e3055568af5dd653cf3957c84b0f43409cc67
Material Incorporated by Reference
Material Incorporated by Reference
(k) None.
Exact source excerpt. Text positions 9547–9597, end exclusive, in the original decoded publication. SHA-256: 5f9f4186bdc284fd4d5116111d055a69aa0e98a7110e30c8860fcf9b7c7d31bc
No replacement link has been established from this edition. The complete historical rule chain and current legal effect remain unknown.
Find all recorded historical references to AD 2010-23-06 · 0 printed reference observations in this pinned collection.
These are observations from one dated publication. Current legal status is unknown; aircraft applicability, installed configuration, compliance and burden require separate evidence. Missing or unparsed conditions remain unknown.
Why these observations are shown
They were extracted offline from the same immutable official HTML source as the complete recorded text. The dated source wording, original text coordinates and exact quote digests are retained. PDF/text agreement and current regulatory effect have not been qualified.
Observation revision: whole-ad-publication-clause-observations-1.0.1. Text SHA-256: 9954d8d323df6d5a454451a221178140b4a668c318a0f0671e65bcdeece63f64. Source manifest: d0e9be89939b237f1960661c7b542dea2963925883466f7c43e05ecb09cdbaab.
Official source · 2010-11-03
Publication text
This is the complete recorded text of this dated publication.
Current legal effect is unknown. Aircraft applicability, installed configuration and compliance require separate evidence. PDF/text agreement has not been evaluated.
Read the complete official publication text
[Federal Register Volume 75, Number 212 (Wednesday, November 3, 2010)]
[Rules and Regulations]
[Pages 67613-67615]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2010-27608]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2005-22690; Directorate Identifier 2005-NE-35-AD;
Amendment 39-16495; AD 2010-23-06]
RIN 2120-AA64
Airworthiness Directives; McCauley Propeller Systems Five-Blade
Propeller Assemblies
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: We are superseding an existing airworthiness directive (AD)
for the products listed above. That AD currently requires removing
certain propeller hubs from service at new, reduced life limits and
eddy current inspections (ECIs) of the propeller hub. This new AD
requires removing certain propeller hubs from service before they
exceed 6,000 hours time-since-new (TSN). This AD was prompted by a
report of a crack in a propeller hub. We are issuing this AD to prevent
cracked propeller hubs, which could cause failure of the propeller hub,
blade separation, and loss of control of the airplane.
DATES: This AD is effective December 8, 2010.
ADDRESSES:
Examining the AD Docket
You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Management Facility
between 9 a.m. and 5 p.m., Monday through Friday, except Federal
holidays. The AD docket contains this AD, the regulatory evaluation,
any comments received, and other information. The address for the
Docket Office (phone: 800-647-5527) is Document Management Facility,
U.S. Department of Transportation, Docket Operations, M-30, West
Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE.,
Washington, DC 20590.
FOR FURTHER INFORMATION CONTACT: Jeff Janusz, Aerospace Engineer,
Wichita Aircraft Certification Office, FAA, Small Airplane Directorate,
1801 Airport Road, Room 100, Wichita, KS 67209, telephone: (316) 946-
4148; fax: (316) 946-4107; e-mail: [email protected].
SUPPLEMENTARY INFORMATION:
Discussion
We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR
[[Page 67614]]
part 39 to supersede airworthiness directive (AD) 2005-24-08, Amendment
39-14388. (70 FR 71756, November 30, 2005). That AD applies to the
specified products. That NPRM published in the Federal Register on June
17, 2010 (75 FR 34390). That NPRM proposed to require:
<bullet> Removing from service the hub of any propeller
assembly, P/N B5JFR36C1101/114GCA-0, C5JFR36C1102/L114GCA-0,
B5JFR36C1103/114HCA-0, or C5JFR36C1104/L114HCA-0, if the hub exceeds
6,000 hours TSN on the effective date of this AD, within 250 hours
time-in-service (TIS) after the effective date of this AD.
<bullet> Removing from service the hub of any propeller
assembly, P/N B5JFR36C1101/114GCA-0, C5JFR36C1102/L114GCA-0,
B5JFR36C1103/114HCA-0, or C5JFR36C1104/L114HCA-0, if the hub has
fewer than 6,000 hours TSN, not later than 6,000 hours TSN.
Comments
We gave the public the opportunity to participate in developing
this AD. We received no comments on the NPRM or on the determination of
the cost to the public.
Conclusion
We reviewed the relevant data and determined that air safety and
the public interest require adopting the AD as proposed--except for
minor editorial changes. We have determined that these minor changes:
<bullet> Are consistent with the intent that was proposed in the
NPRM for correcting the unsafe condition; and
<bullet> Do not add any additional burden upon the public than was
already proposed in the NPRM.
Costs of Compliance
We estimate that this AD affects 30 engines installed on airplanes
of U.S. registry.
We estimate the following costs to comply with this AD:
Estimated Costs
----------------------------------------------------------------------------------------------------------------
Cost per Cost on U.S.
Action Labor cost Parts cost product operators
----------------------------------------------------------------------------------------------------------------
Remove the propeller hub from 42 work-hours x $85 per $6,000 $9,570 $287,100
service. hour = $3,570.
----------------------------------------------------------------------------------------------------------------
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, Section 106, describes the
authority of the FAA Administrator. Subtitle VII, Aviation Programs,
describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701, ``General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
We have determined that this AD will not have federalism
implications under Executive Order 13132. This AD will not have a
substantial direct effect on the States, on the relationship between
the national government and the States, or on the distribution of power
and responsibilities among the various levels of government.
For the reasons discussed above, I certify that this AD:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866,
(2) Is not a ``significant rule'' under DOT Regulatory Policies and
Procedures (44 FR 11034, February 26, 1979),
(3) Will not affect intrastate aviation in Alaska, and
(4) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Safety.
Adoption of the Amendment
0
Accordingly, under the authority delegated to me by the Administrator,
the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by removing airworthiness directive (AD)
2005-24-08, Amendment 39-14388. (70 FR 71756, November 30, 2005), and
adding the following new AD:
2010-23-06 McCauley Propeller Systems: Amendment 39-16495; Docket
No. FAA-2005-22690; Directorate Identifier 2005-NE-35-AD.
Effective Date
(a) This airworthiness directive (AD) is effective December 8,
2010.
Affected ADs
(b) This AD supersedes AD 2005-24-08, Amendment 39-14388.
Applicability
(c) This AD applies to McCauley Propeller Systems propeller
assemblies, part numbers (P/Ns) B5JFR36C1101/114GCA-0, C5JFR36C1102/
L114GCA-0, B5JFR36C1103/114HCA-0, and C5JFR36C1104/L114HCA-0. These
propeller assemblies are installed on BAE Systems (Operations)
Limited Jetstream Model 4100 series airplanes.
Unsafe Condition
(d) This AD results from a report of a cracked propeller hub. We
are issuing this AD to prevent cracked propeller hubs, which could
cause failure of the propeller hub, blade separation, and loss of
control of the airplane.
Compliance
(e) You are responsible for having the actions required by this
AD performed within the compliance times specified unless the
actions have already been done.
Propeller Hub Reduced Life Limits
(f) For any propeller assembly, P/N B5JFR36C1101/114GCA-0,
C5JFR36C1102/L114GCA-0, B5JFR36C1103/114HCA-0, or C5JFR36C1104/
L114HCA-0, with a hub that exceeds 6,000 hours time-since-new (TSN)
on the effective date of this AD, remove the propeller hub from
service within 250 hours time-in-service after the effective date of
this AD.
(g) For any propeller assembly, P/N B5JFR36C1101/114GCA-0,
C5JFR36C1102/L114GCA-0, B5JFR36C1103/114HCA-0, or C5JFR36C1104/
L114HCA-0, with a hub with fewer than 6,000 hours TSN, remove the
propeller hub from service not later than 6,000 hours TSN.
Prohibition of Hubs Exceeding Life Limit
(h) After the effective date of this AD, don't install any hub
removed from any propeller assembly that was removed by paragraphs
(f) or (g) of this AD into any propeller assembly.
[[Page 67615]]
Alternative Methods of Compliance
(i) The Manager, Wichita Aircraft Certification Office, has the
authority to approve alternative methods of compliance for this AD
if requested using the procedures found in 14 CFR 39.19.
Related Information
(j) Contact Jeff Janusz, Aerospace Engineer, Wichita Aircraft
Certification Office, FAA, Small Airplane Directorate, 1801 Airport
Road, Room 100, Wichita, KS 67209, telephone: (316) 946-4148; fax:
(316) 946-4107, for more information about this AD.
Material Incorporated by Reference
(k) None.
Issued in Burlington, Massachusetts, on October 25, 2010.
Karen M. Grant,
Acting Assistant Manager, Engine & Propeller Directorate, Aircraft
Certification Service.
[FR Doc. 2010-27608 Filed 11-2-10; 8:45 am]
BILLING CODE 4910-13-P
Why this text is shown
The complete text was extracted from the official GovInfo HTML edition for this publication. Acquired 2026-10-09T03:12:35.158840+00:00. Text extraction preserves the recorded source wording; it does not determine current requirements.
Open the captured official edition
- Source SHA-256
- b688b2319cff84afee2864691cbe8a94f855a534aab42a24c35f410179017105
- Text SHA-256
- 9954d8d323df6d5a454451a221178140b4a668c318a0f0671e65bcdeece63f64
Return to the full metadata catalog · Search complete publication text · Explore retained publication text and evidence
Coverage and limits
These are dated publication metadata, recorded clauses and literal source observations. Word, model-label, header and reference matches do not establish current legal effect, manufacturer/model identity, aircraft applicability, installed configuration or compliance.
The collection uses 33 explicit annual source snapshots. Source captures and operative-text qualifications have separate states. Missing information remains unknown.