Airworthiness Directives; Learjet Inc. Model 45 Airplanes

[Federal Register Volume 75, Number 51 (Wednesday, March 17, 2010)]
[Rules and Regulations]
[Pages 12667-12670]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2010-5669]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2010-0226; Directorate Identifier 2010-NM-034-AD; 
Amendment 39-16238; AD 2010-06-13]
RIN 2120-AA64


Airworthiness Directives; Learjet Inc. Model 45 Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule; request for comments.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for certain 
Model 45 airplanes. This AD requires a general visual inspection for 
cracked and missing ballscrew assembly sleeves of the flap actuator, 
repetitive non-destructive liquid penetrant inspections of each sleeve 
or flap actuator for cracks, and replacement or modification of the 
flap actuator if necessary. This AD results from reports of cracked and 
missing ballscrew assembly sleeves of the flap actuators. We are 
issuing this AD to detect and correct cracked and missing sleeves, 
which could cause loss of the load-carrying ball bearings on both 
actuators on one flap, resulting in flap asymmetry and loss of control 
of the airplane.

DATES: This AD is effective April 1, 2010.
    The Director of the Federal Register approved the incorporation by 
reference of certain publications listed in the AD as of April 1, 2010.
    We must receive comments on this AD by May 3, 2010.

ADDRESSES: You may send comments by any of the following methods:
    <bullet> Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
    <bullet> Fax: 202-493-2251.
    <bullet> Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue, SE., Washington, DC 20590.
    <bullet> Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue, SE., Washington, DC 20590, between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays.
    For service information identified in this AD, contact Learjet, 
Inc., One Learjet Way, Wichita, Kansas 67209-2942; telephone 316-946-
2000; fax 316-946-2220; e-mail [email protected]; Internet 
http://www.bombardier.com.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Management Facility 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains this AD, the regulatory evaluation, 
any comments received, and other information. The street address for 
the Docket Office (telephone 800-647-5527) is in the ADDRESSES section. 
Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: William Griffith, Aerospace Engineer, 
Airframe Branch, ACE-118W, FAA, Wichita Aircraft Certification Office, 
1801 Airport Road, Room 100, Mid-

[[Page 12668]]

Continent Airport, Wichita, Kansas 67209; telephone (316) 946-4116; fax 
(316) 946-4107.

SUPPLEMENTARY INFORMATION:

Discussion

    We have received reports of cracked and missing ballscrew assembly 
sleeves of the flap actuators. Three flap actuators were found with the 
ballnut sleeves corroded and cracked. Three additional airplanes were 
discovered to contain similar corrosion on the ballnut sleeves. The 
root cause is galvanic corrosion due to an aluminum sleeve installed on 
a steel ballnut. This condition, if not corrected, could cause loss of 
the load-carrying ball bearings on both actuators on one flap, 
resulting in flap asymmetry and loss of control of the airplane.

Relevant Service Information

    We reviewed Bombardier (Learjet) Alert Service Bulletins A45-27-40 
(for Model 45 airplanes, serial numbers 45-005 through 45-380), and 
A40-27-24 (for Model 45 airplanes, serial numbers 45-2001 through 45-
2111), both dated January 11, 2010. These service bulletins describe 
procedures for a general visual inspection for cracked and missing 
ballscrew assembly sleeves of the flap actuator; a non-destructive 
liquid penetrant inspection for cracks of each sleeve and flap 
actuator, depending on the findings; and replacement of the flap 
actuator and ballscrew actuator sleeve if the sleeve is cracked along 
its entire length.
    We also reviewed Bombardier (Learjet) Optional Service Bulletins 
45-27-41 (for Model 45 airplanes, serial numbers 45-005 through 45-
380), and 40-27-25 (for Model 45 airplanes, serial numbers 45-2001 
through 45-2111), both dated January 11, 2010. These service bulletins 
describe procedures for modifying the flap actuator if a certain crack 
length is found and the part does not need to be replaced.

FAA's Determination and Requirements of This AD

    We are issuing this AD because we evaluated all the relevant 
information and determined the unsafe condition described previously is 
likely to exist or develop in other products of the same type design. 
This AD requires accomplishing the actions specified in the service 
information described previously, except as discussed under 
``Differences Between the AD and the Service Information.''

Differences Between the AD and the Service Information

    Although Bombardier (Learjet) Alert Service Bulletins A45-27-40 and 
A40-27-24, both dated January 11, 2010, specify a compliance time of 30 
days after the publication of those service bulletins, this AD requires 
a compliance time of 15 days after the effective date of this AD. We 
have received additional reports of fully cracked sleeves requiring 
replacement. Therefore, we have determined that the 15-day compliance 
time is necessary to address the identified unsafe condition. This 
difference has been coordinated with Learjet.
    Although Bombardier (Learjet) Alert Service Bulletins A45-27-40 and 
A40-27-24, both dated January 11, 2010, do not specify repetitive 
inspections, this AD requires operators to repeat the non-destructive 
liquid penetrant inspections at intervals not to exceed 6 months. The 
repetitive inspections will help determine the extent of the problem in 
the fleet. This difference has been coordinated with Learjet.
    Although Bombardier (Learjet) Alert Service Bulletins A45-27-40 and 
A40-27-24, both dated January 11, 2010, specify to inspect for missing 
ballscrew assembly sleeves, these service bulletins do not specify a 
corrective action if any sleeve is missing. This AD requires replacing 
the flap actuator if any sleeve is missing. This difference has been 
coordinated with Learjet.
    Bombardier (Learjet) Alert Service Bulletins A45-27-40 and A40-27-
24, both dated January 11, 2010, specify modifying or replacing the 
flap actuator as corrective action for a cracked sleeve, depending on 
the percentage of the length of the sleeve that is cracked. This AD 
instead requires replacing the actuator if a sleeve is cracked along 
its entire length, and modifying the actuator for any cracked sleeve 
that is not cracked along its entire length. This difference has been 
coordinated with Learjet.

Interim Action

    We consider this AD interim action. Learjet Inc. is currently 
developing a new modification of the ballscrew assembly of the flap 
actuator that will address the unsafe condition identified in this AD. 
Once this modification is developed, approved, and available, we might 
consider additional rulemaking.

FAA's Justification and Determination of the Effective Date

    We have received reports of cracked and missing ballscrew assembly 
sleeves of the flap actuators. Cracked and missing sleeves could result 
in the loss of the load-carrying ball bearings from the assembly, 
resulting in the loss of the flap drive load path for that actuator. 
Loss of the sleeves on both actuators on one flap could result in flap 
asymmetry, resulting in loss of control of the airplane. Because of our 
requirement to promote safe flight of civil aircraft and thus the 
critical need to ensure structural integrity of the ballscrew assembly 
sleeves of the flap actuator and the short compliance time involved 
with this action, this AD must be issued immediately.
    Because an unsafe condition exists that requires the immediate 
adoption of this AD, we find that notice and opportunity for prior 
public comment hereon are impracticable and that good cause exists for 
making this amendment effective in less than 30 days.

Comments Invited

    This AD is a final rule that involves requirements affecting flight 
safety, and we did not provide you with notice and an opportunity to 
provide your comments before it becomes effective. However, we invite 
you to send any written data, views, or arguments about this AD. Send 
your comments to an address listed under the ADDRESSES section. Include 
``Docket No. FAA-2010-0226; Directorate Identifier 2010-NM-034-AD'' at 
the beginning of your comments. We specifically invite comments on the 
overall regulatory, economic, environmental, and energy aspects of this 
AD. We will consider all comments received by the closing date and may 
amend this AD because of those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this AD.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for

[[Page 12669]]

safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under DOT Regulatory Policies and 
Procedures (44 FR 11034, February 26, 1979), and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    You can find our regulatory evaluation and the estimated costs of 
compliance in the AD Docket.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

0
Accordingly, under the authority delegated to me by the Administrator, 
the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new AD:

2010-06-13 Learjet Inc.: Amendment 39-16238. Docket No. FAA-2010-
0226; Directorate Identifier 2010-NM-034-AD.

Effective Date

    (a) This airworthiness directive (AD) is effective April 1, 
2010.

Affected ADs

    (b) None.

Applicability

    (c) This AD applies to Learjet Inc. Model 45 airplanes, 
certificated in any category, serial numbers 45-005 through 45-380 
inclusive and 45-2001 through 45-2111 inclusive.

Subject

    (d) Air Transport Association (ATA) of America Code 27: Flight 
Controls.

Unsafe Condition

    (e) This AD results from reports of cracked and missing 
ballscrew assembly sleeves of the flap actuators. The Federal 
Aviation Administration is issuing this AD to detect and correct 
cracked and missing sleeves, which could cause loss of the load-
carrying ball bearings on both actuators on one flap, resulting in 
flap asymmetry and loss of control of the airplane.

Compliance

    (f) You are responsible for having the actions required by this 
AD performed within the compliance times specified, unless the 
actions have already been done.

General Visual Inspection

    (g) Within 15 days after the effective date of this AD, do a 
general visual inspection for cracked or missing ballscrew assembly 
sleeves of the flap actuator, in accordance with the Accomplishment 
Instructions of Bombardier (Learjet) Alert Service Bulletin A45-27-
40 (for Model 45 airplanes, serial numbers 45-005 through 45-380); 
or Bombardier (Learjet) Alert Service Bulletin A40-27-24 (for Model 
45 airplanes, serial numbers 45-2001 through 45-2111); both dated 
January 11, 2010. Thereafter, do the actions in paragraph (h) or 
(i), as applicable, of this AD.

    Note 1: For the purposes of this AD, a general visual inspection 
is: ``A visual examination of an interior or exterior area, 
installation, or assembly to detect obvious damage, failure, or 
irregularity. This level of inspection is made from within touching 
distance unless otherwise specified. A mirror may be necessary to 
ensure visual access to all surfaces in the inspection area. This 
level of inspection is made under normally available lighting 
conditions such as daylight, hangar lighting, flashlight, or 
droplight and may require removal or opening of access panels or 
doors. Stands, ladders, or platforms may be required to gain 
proximity to the area being checked.''

Non-Destructive Liquid Penetrant Inspection (Sleeve Is Present and Not 
Cracked Along Its Entire Length)

    (h) During the general visual inspection required by paragraph 
(g) of this AD, if the sleeve is present and not cracked along its 
entire length, before further flight after accomplishing the general 
visual inspection, do a non-destructive liquid penetrant inspection 
to detect cracking of the flap actuators, in accordance with 
Accomplishment Instructions of Bombardier (Learjet) Alert Service 
Bulletin A45-27-40, or Bombardier (Learjet) Alert Service Bulletin 
A40-27-24, both dated January 11, 2010.
    (1) If no crack is found during the non-destructive liquid 
penetrant inspection, repeat the inspection thereafter at intervals 
not to exceed 6 months.
    (2) If any crack is found during the non-destructive liquid 
penetrant inspection, before further flight, modify the flap 
actuator, in accordance with the Accomplishment Instructions of 
Bombardier (Learjet) Optional Service Bulletin 45-27-41 (for Model 
45 airplanes, serial numbers 45-005 through 45-380); or Bombardier 
(Learjet) Optional Service Bulletin 40-27-25 (for Model 45 
airplanes, serial numbers 45-2001 through 45-2111); both dated 
January 11, 2010. Repeat the non-destructive liquid penetrant 
inspection of the half (modified) sleeve thereafter at intervals not 
to exceed 6 months. If any crack is found in any half (modified) 
sleeve, before further flight, replace the sleeve with a new half 
sleeve, in accordance with the Accomplishment Instructions of 
Bombardier (Learjet) Optional Service Bulletin 45-27-41, or 
Bombardier (Learjet) Optional Service Bulletin 40-27-25, both dated 
January 11, 2010, and repeat the non-destructive liquid penetrant 
inspection of the half sleeve thereafter at intervals not to exceed 
6 months.

Replacement (Sleeve Is Missing or Cracked Along Its Entire Length)

    (i) During the general visual inspection required by paragraph 
(g) of this AD, if the sleeve is missing or cracked along its entire 
length, before further flight after accomplishing the general visual 
inspection, replace the actuator with a new or serviceable actuator, 
in accordance with the Accomplishment Instructions of Bombardier 
(Learjet) Alert Service Bulletin A45-27-40, or Bombardier (Learjet) 
Alert Service Bulletin A40-27-24, both dated January 11, 2010. 
Within 6 months after any actuator replacement required by paragraph 
(i) of this AD: Do a non-destructive liquid penetrant inspection to 
detect cracking of the actuator, in accordance with Accomplishment 
Instructions of Bombardier (Learjet) Alert Service Bulletin A45-27-
40, or Bombardier (Learjet) Alert Service Bulletin A40-27-24, both 
dated January 11, 2010.
    (1) If no crack is found during the non-destructive liquid 
penetrant inspection, repeat the inspection thereafter at intervals 
not to exceed 6 months.
    (2) If any crack is found during the non-destructive liquid 
penetrant inspection, but the sleeve is not cracked along its entire 
length, before further flight, modify the flap actuator, in 
accordance with the Accomplishment Instructions of Bombardier 
(Learjet) Optional Service Bulletin 45-27-41, or Bombardier 
(Learjet) Optional Service Bulletin 40-27-25, both dated January 11, 
2010. Repeat the non-destructive liquid penetrant inspection of the 
half (modified) sleeves thereafter at intervals not to exceed 6 
months. If any crack is found in any half (modified) sleeve, before 
further flight, replace the sleeve with a new half sleeve, in 
accordance with the Accomplishment Instructions of Bombardier 
(Learjet) Optional Service Bulletin 45-27-41, or Bombardier 
(Learjet) Optional Service Bulletin 40-27-25, both dated January 11, 
2010. Repeat the non-destructive liquid penetrant inspection of the 
half sleeve thereafter at intervals not to exceed 6 months.
    (3) If the sleeve is cracked along its entire length, before 
further flight, replace the actuator with a new or serviceable 
actuator, in accordance with the Accomplishment Instructions of 
Bombardier (Learjet) Optional

[[Page 12670]]

Service Bulletin 45-27-41, or Bombardier (Learjet) Optional Service 
Bulletin 40-27-25, both dated January 11, 2010, and repeat the non-
destructive liquid penetrant inspection of the sleeve thereafter at 
intervals not to exceed 6 months.

    Note 2: Guidance on modification of the flap actuator can be 
found in Microtecnica Service Bulletin 27-0018, dated November 24, 
2009.

Parts Installation

    (j) As of the effective date of this AD, no person may install, 
on any airplane, a ballscrew assembly sleeve of the flap actuator, 
unless the actuator has been modified according to Bombardier 
(Learjet) Optional Service Bulletin 45-27-41, or Bombardier 
(Learjet) Optional Service Bulletin 40-27-25, both dated January 11, 
2010.

Reporting Requirement

    (k) Submit a one-time report of the findings of the general 
visual inspection and the initial non-destructive liquid penetrant 
inspection required by this AD to Chris Broadrick, Bombardier 
Aerospace, Project Coordinator--Fielding Specialist, Customer 
Support Engineering, One Learjet Way, P.O. Box 7707, Wichita, Kansas 
67209; telephone 316-946-2315; fax 316-946-8908; e-mail 
[email protected]; at the applicable time 
specified in paragraph (k)(1) or (k)(2) of this AD. The report must 
include airplane serial number, flap actuator part number, flap 
actuator serial number, and flap actuator time in service (in 
hours). Under the provisions of the Paperwork Reduction Act (44 
U.S.C. 3501 et seq.), the Office of Management and Budget (OMB) has 
approved the information collection requirements contained in this 
AD and has assigned OMB Control Number 2120-0056.
    (1) If the inspection was done on or after the effective date of 
this AD: Submit the report within 10 days after the inspection.
    (2) If the inspection was done before the effective date of this 
AD: Submit the report within 10 days after the effective date of 
this AD.

Special Flight Permits

    (l) Special flight permits may be issued in accordance with 
sections 21.197 and 21.199 of the Federal Aviation Regulations (14 
CFR 21.197 and 21.199) to operate the airplane to a location where 
the airplane can be modified, unless cracks are discovered in both 
an inboard and outboard actuator sleeve for any flap.

Alternative Methods of Compliance (AMOCs)

    (m)(1) The Manager, Wichita Aircraft Certification Office (ACO), 
FAA, has the authority to approve AMOCs for this AD, if requested 
using the procedures found in 14 CFR 39.19. Send information to 
ATTN: William Griffith, Aerospace Engineer, Airframe Branch, ACE-
118W, FAA, Wichita ACO, 1801 Airport Road, Room 100, Mid-Continent 
Airport, Wichita, Kansas 67209; telephone (316) 946-4116; fax (316) 
946-4107.
    (2) To request a different method of compliance or a different 
compliance time for this AD, follow the procedures in 14 CFR 39.19. 
Before using any approved AMOC on any airplane to which the AMOC 
applies, notify your principal maintenance inspector (PMI) or 
principal avionics inspector (PAI), as appropriate, or lacking a 
principal inspector, your local Flight Standards District Office. 
The AMOC approval letter must specifically reference this AD.

Material Incorporated by Reference

    (n) You must use the service information included in Table 1 of 
this AD, as applicable, to do the actions required by this AD, 
unless the AD specifies otherwise.
    (1) The Director of the Federal Register approved the 
incorporation by reference of this service information under 5 
U.S.C. 552(a) and 1 CFR part 51.
    (2) For service information identified in this AD, contact 
Learjet, Inc., One Learjet Way, Wichita, Kansas 67209-2942; 
telephone 316-946-2000; fax 316-946-2220; e-mail 
[email protected]; Internet http://www.bombardier.com.
    (3) You may review copies of the service information at the FAA, 
Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, 
Washington. For information on the availability of this material at 
the FAA, call 425-227-1221.
    (4) You may also review copies of the service information that 
is incorporated by reference at the National Archives and Records 
Administration (NARA). For information on the availability of this 
material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.

               Table 1--Material Incorporated by Reference
------------------------------------------------------------------------
               Document                               Date
------------------------------------------------------------------------
Bombardier (Learjet) Alert Service      January 11, 2010.
 Bulletin A40-27-24.
Bombardier (Learjet) Alert Service      January 11, 2010.
 Bulletin A45-27-40.
Bombardier (Learjet) Optional Service   January 11, 2010.
 Bulletin 40-27-25.
Bombardier (Learjet) Optional Service   January 11, 2010.
 Bulletin 45-27-41.
------------------------------------------------------------------------


    Issued in Renton, Washington, on March 9, 2010.
Jeffrey E. Duven,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2010-5669 Filed 3-16-10; 8:45 am]
BILLING CODE 4910-13-P

The complete text was extracted from the official GovInfo HTML edition for this publication. Acquired 2026-10-09T03:17:01.615352+00:00. Text extraction preserves the recorded source wording; it does not determine current requirements.

Open the captured official edition

Source SHA-256

fd0b872fb923a5a28930256c4d350a0220a0029ee2343f96074026cd069e9f6a

Text SHA-256

48fa925f8c6a4dc63aa4a31a5829b5523b2cfde7ac61abf1b457e69c47213753