Airworthiness Directives; Dassault Aviation Model FALCON 7X Airplanes

[Federal Register Volume 76, Number 120 (Wednesday, June 22, 2011)]
[Rules and Regulations]
[Pages 36283-36285]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2011-15368]


=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2011-0259; Directorate Identifier 2010-NM-196-AD; 
Amendment 39-16730; AD 2011-13-07]
RIN 2120-AA64


Airworthiness Directives; Dassault Aviation Model FALCON 7X 
Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We are superseding an existing airworthiness directive (AD) 
that applies to the products listed above. This AD results from 
mandatory continuing airworthiness information (MCAI) originated by an 
aviation authority of another country to identify and correct an unsafe 
condition on an aviation product. The MCAI describes the unsafe 
condition as:

    Several occurrences of untimely radio-altimeter lock-up have 
been reported, where the failed radio-altimeter indicated a negative 
distance to the ground despite the aircraft was flying at medium or 
high altitude.
    A locked radio-altimeter <greek-i>1 leads to untimely inhibition 
of warnings that could be displayed along with certain abnormal 
conditions while the avionic system switches into landing mode 
during altitude cruise.
* * * * *
    [Untimely radio altimeter lock-up] may cause the crew to be 
unaware of possible system failures that could require urgent crew's 
actions.
* * * * *

We are issuing this AD to require actions to correct the unsafe 
condition on these products.

DATES: This AD becomes effective July 27, 2011.

ADDRESSES: You may examine the AD docket on the Internet at http://

[[Page 36284]]

www.regulations.gov or in person at the U.S. Department of 
Transportation, Docket Operations, M-30, West Building Ground Floor, 
Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC.

FOR FURTHER INFORMATION CONTACT: Tom Rodriguez, Aerospace Engineer, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425) 
227-1137; fax (425) 227-1149.

SUPPLEMENTARY INFORMATION:

Discussion

    We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR 
part 39 to include an AD that would apply to the specified products. 
That NPRM was published in the Federal Register on March 29, 2011 (76 
FR 17364), and proposed to supersede AD 2010-02-02, Amendment 39-16173 
(75 FR 1697, January 13, 2010). That NPRM proposed to correct an unsafe 
condition for the specified products. The MCAI states:

    Several occurrences of untimely radio-altimeter lock-up have 
been reported, where the failed radio-altimeter indicated a negative 
distance to the ground despite the aircraft was flying at medium or 
high altitude.
    A locked radio-altimeter <greek-i>1 leads to untimely inhibition 
of warnings that could be displayed along with certain abnormal 
conditions while the avionic system switches into landing mode 
during altitude cruise.
* * * * *
    [Untimely radio altimeter lock-up] may cause the crew to be 
unaware of possible system failures that could require urgent crew's 
actions.
    To address this unsafe condition, [EASA] AD 2009-0208 was issued 
on 13 October 2009 [which corresponds with FAA AD 2010-02-02]. It 
mandated application of a new abnormal Airplane Flight Manual (AFM) 
procedure when radio-altimeter <greek-i>1 lock-up occurs and 
prohibited dispatch of the aeroplane with any radio-altimeter 
inoperative.
    Since AD 2009-0208 was issued, Easy avionics load 10 has been 
developed with change M0566 or Service Bulletin (SB) Falcon 7X 
n[deg]100 that brings new features to display a ``RA miscompare'' 
flag on both Primary Display Units (PDU) and accepts a commanded 
system reversion to the correct radio-altimeter output.
    EASA AD 2009-0208R1 is issued to allow not deactivating radio-
altimeter <greek-i>1 in case lock-up conditions occur in flight for 
aeroplanes on which M0566 or SB Falcon 7X n[deg]100 has been 
embodied.

You may obtain further information by examining the MCAI in the AD 
docket.

Comments

    We gave the public the opportunity to participate in developing 
this AD. We received no comments on the NPRM or on the determination of 
the cost to the public.

Conclusion

    We reviewed the available data and determined that air safety and 
the public interest require adopting the AD as proposed.

Differences Between This AD and the MCAI or Service Information

    We have reviewed the MCAI and related service information and, in 
general, agree with their substance. But we might have found it 
necessary to use different words from those in the MCAI to ensure the 
AD is clear for U.S. operators and is enforceable. In making these 
changes, we do not intend to differ substantively from the information 
provided in the MCAI and related service information.
    We might also have required different actions in this AD from those 
in the MCAI in order to follow our FAA policies. Any such differences 
are highlighted in a Note within the AD.

Costs of Compliance

    We estimate that this AD will affect about 24 products of U.S. 
registry.
    The actions that are required by AD 2010-02-02 and retained in this 
AD take about 1 work-hour per product, at an average labor rate of $85 
per work-hour. Based on these figures, the estimated cost of the 
currently required actions is $85 per product.
    We estimate that it will take about 1 work-hour per product to 
comply with the new basic requirements of this AD. The average labor 
rate is $85 per work-hour. Based on these figures, we estimate the cost 
of this AD to the U.S. operators to be $2,040, or $85 per product.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this AD will not have federalism implications 
under Executive Order 13132. This AD will not have a substantial direct 
effect on the States, on the relationship between the national 
government and the States, or on the distribution of power and 
responsibilities among the various levels of government.
    For the reasons discussed above, I certify this AD:
    1. Is not a ''significant regulatory action'' under Executive Order 
12866;
    2. Is not a ''significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979); and
    3. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this AD and placed it in the AD docket.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Operations office 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains the NPRM, the regulatory evaluation, 
any comments received, and other information. The street address for 
the Docket Operations office (telephone (800) 647-5527) is in the 
ADDRESSES section. Comments will be available in the AD docket shortly 
after receipt.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by removing Amendment 39-16173 (75 FR 
1697, January 13, 2010) and adding the following new AD:


[[Page 36285]]


2011-13-07 Dassault Aviation: Amendment 39-16730. Docket No. FAA-
2011-0259; Directorate Identifier 2010-NM-196-AD.

Effective Date

    (a) This airworthiness directive (AD) becomes effective July 27, 
2011.

Affected ADs

    (b) This AD supersedes AD 2010-02-02, Amendment 39-16173.

Applicability

    (c) This AD applies to Dassault Aviation Model FALCON 7X 
airplanes, certificated in any category, all serial numbers.

Subject

    (d) Air Transport Association (ATA) of America Code 34: 
Navigation.

Reason

    (e) The mandatory continuing airworthiness information (MCAI) 
states:

    Several occurrences of untimely radio-altimeter lock-up have 
been reported, where the failed radio-altimeter indicated a negative 
distance to the ground despite the aircraft was flying at medium or 
high altitude.
    A locked radio-altimeter <greek-i>1 leads to untimely inhibition 
of warnings that could be displayed along with certain abnormal 
conditions while the avionic system switches into landing mode 
during altitude cruise.
* * * * *
    [Untimely radio altimeter lock-up] may cause the crew to be 
unaware of possible system failures that could require urgent crew's 
actions.
* * * * *

Compliance

    (f) You are responsible for having the actions required by this 
AD performed within the compliance times specified, unless the 
actions have already been done.

Restatement of Requirements of AD 2010-02-02, With Revised Affected 
Airplanes

    (g) For airplanes on which modification M0566 or Dassault 
Service Bulletin Falcon 7X-100 has not been accomplished: Within 14 
days after January 28, 2010 (the effective date of AD 2010-02-02), 
revise the Limitations Section of the Dassault Falcon 7X Airplane 
Flight Manual (AFM) to include the following statement. This may be 
done by inserting a copy of this AD in the AFM.
    ``If radio-altimeter <greek-i>1 lock-up conditions occur in 
flight, power off radio-altimeter <greek-i>1, in accordance with the 
instructions of Falcon 7X AFM procedure 3-140-65.
    Dispatch of the airplane with any radio-altimeter inoperative is 
prohibited.''

    Note 1:  When a statement identical to that in paragraph (g) of 
this AD has been included in the general revisions of the AFM, the 
general revisions may be inserted into the AFM, and the copy of this 
AD may be removed from the AFM.

New Requirements of This AD

    (h) For airplanes on which M0566 or Dassault Service Bulletin 
Falcon 7X-100 has been accomplished: Within 14 days after the 
effective date of this AD, revise the Limitations Section of the 
Dassault Falcon 7X AFM to include the following statement. This may 
be done by inserting a copy of this AD in the AFM. Doing this 
revision terminates the requirements of paragraph (g) of this AD.
    ``If radio-altimeter <greek-i>1 lock-up conditions occur in 
flight, revert to the correct radio-altimeter output, in accordance 
with the instructions of Falcon 7X AFM procedure 3-140-65B and 3-
140-70A.
    Dispatch of the airplane with any radio-altimeter inoperative is 
prohibited.''

    Note 2:  When a statement identical to that in paragraph (h) of 
this AD has been included in the general revisions of the AFM, the 
general revisions may be inserted into the AFM, and the copy of this 
AD may be removed from the AFM.

FAA AD Differences

    Note 3:  This AD differs from the MCAI and/or service 
information as follows: No differences.

Other FAA AD Provisions

    (i) The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
has the authority to approve AMOCs for this AD, if requested using 
the procedures found in 14 CFR 39.19. In accordance with 14 CFR 
39.19, send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the International Branch, send it to ATTN: Tom 
Rodriguez, Aerospace Engineer, International Branch, ANM-116, 
Transport Airplane Directorate, FAA, 1601 Lind Avenue, SW., Renton, 
Washington 98057-3356; telephone (425) 227-1137; fax (425) 227-1149. 
Information may be e-mailed to: [email protected]. 
Before using any approved AMOC, notify your appropriate principal 
inspector, or lacking a principal inspector, the manager of the 
local flight standards district office/certificate holding district 
office. The AMOC approval letter must specifically reference this 
AD.
    (2) Airworthy Product: For any requirement in this AD to obtain 
corrective actions from a manufacturer or other source, use these 
actions if they are FAA-approved. Corrective actions are considered 
FAA-approved if they are approved by the State of Design Authority 
(or their delegated agent). You are required to assure the product 
is airworthy before it is returned to service.

Related Information

    (j) Refer to MCAI European Aviation Safety Agency (EASA) 
Airworthiness Directive 2009-0208R1, dated June 2, 2010, for related 
information.

Material Incorporated by Reference

    (k) None.

    Issued in Renton, Washington, on June 14, 2011.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2011-15368 Filed 6-21-11; 8:45 am]
BILLING CODE 4910-13-P

The complete text was extracted from the official GovInfo HTML edition for this publication. Acquired 2026-10-09T03:08:30.378270+00:00. Text extraction preserves the recorded source wording; it does not determine current requirements.

Open the captured official edition

Source SHA-256

14272ed18634a97b44ba8c03a5610f8bababc5e80ecd5536b4156bf03d4fca49

Text SHA-256

5c587f1d79a87067d03cacf70436a9c6e5cefb40c61ef514fef4059f9fcd3872