Airworthiness Directives; Bombardier, Inc. Airplanes

[Federal Register Volume 79, Number 73 (Wednesday, April 16, 2014)]
[Rules and Regulations]
[Pages 21387-21389]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2014-08452]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2013-1069; Directorate Identifier 2013-NM-197-AD; 
Amendment 39-17827; AD 2014-08-03]
RIN 2120-AA64


Airworthiness Directives; Bombardier, Inc. Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for certain 
Bombardier, Inc. Model CL-600-2C10 (Regional Jet Series 700, 701, & 
702) airplanes, Model CL-600-2D15 (Regional Jet Series 705) airplanes, 
Model CL-600-2D24 (Regional Jet Series 900) airplanes, and Model CL-
600-2E25 (Regional Jet Series 1000) airplanes. This AD was prompted by 
a determination that for certain slat system failure cases, the 
resulting slat skew could lead to failure of the slat system. This AD 
requires replacing certain locking plates with certain anti-migration 
assemblies on certain left and right wing slats. We are issuing this AD 
to prevent failure of the eccentric pins at the slat track attachment, 
and slat panels consequently disconnecting from the wing, leading to 
the loss of the airplane.

DATES: This AD becomes effective May 21, 2014.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of May 21, 
2014.

ADDRESSES: You may examine the AD docket on the Internet at http://www.regulations.gov/#!docketDetail;D=FAA-2013-1069; or in person at the 
Docket Management Facility, U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC.
    For service information identified in this AD, contact Bombardier, 
Inc., 400 C[ocirc]te-Vertu Road West, Dorval, Qu[eacute]bec H4S 1Y9, 
Canada; telephone 514-855-5000; fax 514-855-7401; email 
[email protected]; Internet http://www.bombardier.com. You 
may view this referenced service information at the FAA, Transport 
Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information 
on the availability of this material at the FAA, call 425-227-1221.

FOR FURTHER INFORMATION CONTACT: Cesar Gomez, Aerospace Engineer, 
Airframe and Mechanical Systems Branch, ANE-171, FAA, New York Aircraft 
Certification Office, 1600 Stewart Avenue, Suite 410, Westbury, NY 
11590; telephone (516) 228-7318; fax (516) 794-5531.

SUPPLEMENTARY INFORMATION:

Discussion

    We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR 
part 39 by adding an AD that would apply to certain Bombardier, Inc. 
Model CL-600-2C10 (Regional Jet Series 700, 701, & 702) airplanes, 
Model CL-600-2D15 (Regional Jet Series 705) airplanes, Model CL-600-
2D24 (Regional Jet Series 900) airplanes, and Model CL-600-2E25 
(Regional Jet Series 1000) airplanes. The NPRM published in the Federal 
Register on January 2, 2014 (79 FR 70).

[[Page 21388]]

    Transport Canada Civil Aviation (TCCA), which is the airworthiness 
authority for Canada, has issued Canadian Airworthiness Directive CF-
2013-31, dated October 8, 2013 (referred to after this as the Mandatory 
Continuing Airworthiness Information, or ``the MCAI''), to correct an 
unsafe condition. The MCAI states:

    It was discovered that for certain slat system jam-disconnect 
failure cases, the resulting slat skew could lead to failure of the 
eccentric pin at the slat track 3-3 attachment. If the pin migrates 
out of the attachment lugs, this could cause the No. 3 slat panels 
to disconnect from the wing and could lead to the loss of the 
aeroplane.
    This [Canadian] AD mandates the replacement of the locking plate 
with an anti-migration assembly on both the left and right No. 3 
slats.

    You may examine the MCAI in the AD docket on the Internet at http://www.regulations.gov/#!documentDetail;D=FAA-2013-1069-0002.

Comments

    We gave the public the opportunity to participate in developing 
this AD. We received no comments on the NPRM (79 FR 70, January 2, 
2014) or on the determination of the cost to the public.

Conclusion

    We reviewed the relevant data and determined that air safety and 
the public interest require adopting this AD as proposed except for 
minor editorial changes. We have determined that these minor changes:
    <bullet> Are consistent with the intent that was proposed in the 
NPRM (79 FR 70, January 2, 2014) for correcting the unsafe condition; 
and
    <bullet> Do not add any additional burden upon the public than was 
already proposed in the NPRM (79 FR 70, January 2, 2014).

Costs of Compliance

    We estimate that this AD affects 401 airplanes of U.S. registry.
    We also estimate that it will take about 9 work-hours per product 
to comply with the basic requirements of this AD. The average labor 
rate is $85 per work-hour. Required parts will cost about $780 per 
product. Based on these figures, we estimate the cost of this AD on 
U.S. operators to be $619,545, or $1,545 per product.
    According to the manufacturer, some of the costs of this AD may be 
covered under warranty, thereby reducing the cost impact on affected 
individuals. We do not control warranty coverage for affected 
individuals. As a result, we have included all costs in our cost 
estimate.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this AD will not have federalism implications 
under Executive Order 13132. This AD will not have a substantial direct 
effect on the States, on the relationship between the national 
government and the States, or on the distribution of power and 
responsibilities among the various levels of government.
    For the reasons discussed above, I certify that this AD:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov/#!docketDetail;D=FAA-2013-1069; or in person at the 
Docket Management Facility between 9 a.m. and 5 p.m., Monday through 
Friday, except Federal holidays. The AD docket contains this AD, the 
regulatory evaluation, any comments received, and other information. 
The street address for the Docket Operations office (telephone 800-647-
5527) is in the ADDRESSES section.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

2014-08-03 Bombardier, Inc. Amendment 39-17827. Docket No. FAA-2013-
1069; Directorate Identifier 2013-NM-197-AD.

(a) Effective Date

    This AD becomes effective May 21, 2014.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Bombardier, Inc. airplanes, certificated in 
any category, identified in paragraphs (c)(1), (c)(2), and (c)(3) of 
this AD.
    (1) Bombardier, Inc. Model CL-600-2C10 (Regional Jet Series 700, 
701, & 702) airplanes, serial numbers 10002 through 10335 inclusive.
    (2) Bombardier, Inc. Model CL-600-2D15 (Regional Jet Series 705) 
airplanes, and Bombardier, Inc. Model CL-600-2D24 (Regional Jet 
Series 900) airplanes, serial numbers 15001 through 15293 inclusive.
    (3) Bombardier, Inc. Model CL-600-2E25 (Regional Jet Series 
1000) airplanes, serial numbers 19002 through 19036 inclusive.

(d) Subject

    Air Transport Association (ATA) of America Code 27, Flight 
controls.

(e) Reason

    This AD was prompted by a determination that for certain slat 
system jam-disconnect failure cases, the resulting slat skew could 
lead to failure of the eccentric pin at the slat track attachment. 
If the pin migrates out of the attachment lugs, this could cause 
certain slat panels to disconnect from the wing. We are issuing this 
AD to prevent failure of the eccentric pins at the slat track 
attachment, and slat panels consequently disconnecting from the 
wing, leading to the loss of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

[[Page 21389]]

(g) Replacement

    Within 6,000 flight hours or 30 months, whichever occurs first, 
after the effective date of this AD: Remove and replace the locking 
plate having part number (P/N) CC670-12076-1 with an anti-migration 
assembly having P/N CC670-12370-1, on both the left and right number 
3 slats, in accordance with the Accomplishment Instructions of 
Bombardier Service Bulletin 670BA-27-066, dated June 10, 2013.

(h) Parts Installation Prohibition

    As of the effective date of this AD, no person may install any 
locking plate having P/N CC670-12076-1 on any airplane.

(i) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, New 
York Aircraft Certification Office (ACO), ANE-170, FAA, has the 
authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send tour request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the New York ACO, send it to ATTN: Program Manager, 
Continuing Operational Safety, FAA, New York ACO, 1600 Stewart 
Avenue, Suite 410, Westbury, NY 11590; telephone 516-228-7300; fax 
516-794-5531. Before using any approved AMOC, notify your 
appropriate principal inspector, or lacking a principal inspector, 
the manager of the local flight standards district office/
certificate holding district office. The AMOC approval letter must 
specifically reference this AD.
    (2) Airworthy Product: For any requirement in this AD to obtain 
corrective actions from a manufacturer, use these actions if they 
are FAA-approved. Corrective actions are considered FAA-approved if 
they were approved by the State of Design Authority (or its 
delegated agent, or the Design Approval Holder with a State of 
Design Authority's design organization approval, as applicable). You 
are required to ensure the product is airworthy before it is 
returned to service.

(j) Related Information

    Refer to Mandatory Continuing Airworthiness Information (MCAI) 
Canadian Airworthiness Directive CF-2013-31, dated October 8, 2013, 
for related information. This MCAI may be found in the AD docket on 
the Internet at http://www.regulations.gov/#!documentDetail;D=FAA-
2013-1069-0002.

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) Bombardier Service Bulletin 670BA-27-066, dated June 10, 
2013.
    (ii) Reserved.
    (3) For service information identified in this AD, contact 
Bombardier, Inc., 400 C[ocirc]te-Vertu Road West, Dorval, 
Qu[eacute]bec H4S 1Y9, Canada; telephone 514-855-5000; fax 514-855-
7401; email [email protected]; Internet http://www.bombardier.com.
    (4) You may view this service information at the FAA, Transport 
Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For 
information on the availability of this material at the FAA, call 
425-227-1221.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued in Renton, Washington, on April 4, 2014.
Jeffrey E. Duven,
Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2014-08452 Filed 4-15-14; 8:45 am]
BILLING CODE 4910-13-P

The complete text was extracted from the official GovInfo HTML edition for this publication. Acquired 2026-10-09T02:48:27.926541+00:00. Text extraction preserves the recorded source wording; it does not determine current requirements.

Open the captured official edition

Source SHA-256

f0016e099e95e9ca39b0f9a8c657864b6634c14ff3de5704d17bb55a9b3ce3c6

Text SHA-256

b1a0987a2650291a2b4088249407851e80bc833f072bdbbec873adfe40e57458