Airworthiness Directives; Bombardier, Inc. Airplanes

[Federal Register Volume 79, Number 135 (Tuesday, July 15, 2014)]
[Rules and Regulations]
[Pages 41104-41108]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2014-15655]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2013-0296; Directorate Identifier 2012-NM-102-AD; 
Amendment 39-17861; AD 2014-11-10]
RIN 2120-AA64


Airworthiness Directives; Bombardier, Inc. Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We are superseding Airworthiness Directive (AD) 2008-08-09 for 
certain Bombardier, Inc. Model CL-600-2B19 (Regional Jet Series 100 & 
440) airplanes. AD 2008-08-09 required revising the airworthiness 
limitations (AWL) section of the Instructions for Continued 
Airworthiness by incorporating procedures for repetitive functional 
tests of the pilot input lever of the pitch feel simulator (PFS) units 
and corrective actions if necessary. This new AD requires replacing 
certain PFS units with new redesigned PFS units, which would terminate 
the repetitive functional tests; and both adding and removing certain 
airplanes from the applicability. This AD was prompted by reports that 
the shear pin in the input lever of several PFS units failed due to 
fatigue; and by the development of a re-designed PFS unit, which 
eliminates the need for repetitive functional tests. We are issuing 
this AD to prevent undetected failure of the shear pins of both PFS 
units simultaneously, which could result in loss of pitch feel forces 
and consequent reduced control of the airplane.

DATES: This AD becomes effective August 19, 2014.
    The Director of the Federal Register approved the incorporation by 
reference of certain publications listed in this AD as of August 19, 
2014.

ADDRESSES: You may examine the AD docket on the Internet at http://www.regulations.gov/#!docketDetail;D=FAA-2013-0296; or in person at the 
Docket Management Facility, U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC.
    For service information identified in this AD, contact Bombardier, 
Inc., 400 C[ocirc]te-Vertu Road West, Dorval, Qu[eacute]bec H4S 1Y9, 
Canada; telephone 514-855-5000; fax 514-855-7401; email thd.crj@

[[Page 41105]]

aero.bombardier.com; Internet http://www.bombardier.com. You may view 
this referenced service information at the FAA, Transport Airplane 
Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the 
availability of this material at the FAA, call 425-227-1221.

FOR FURTHER INFORMATION CONTACT: Cesar Gomez, Aerospace Engineer, 
Airframe and Mechanical Systems Branch, ANE-171, FAA, New York Aircraft 
Certification Office, 1600 Stewart Avenue, Suite 410, Westbury, NY 
11590; telephone 516-228-7318; fax 516-794-5531.

SUPPLEMENTARY INFORMATION:

Discussion

    We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR 
part 39 to supersede AD 2008-08-09, Amendment 39-15461 (73 FR 19979, 
April 14, 2008). AD 2008-08-09 applied to certain Bombardier, Inc. 
Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes. The NPRM 
published in the Federal Register on April 9, 2013 (78 FR 21074).
    Transport Canada Civil Aviation (TCCA), which is the aviation 
authority for Canada, has issued Canadian Airworthiness Directive CF-
2005-41R1, dated May 10, 2012 (referred to after this as the Mandatory 
Continuing Airworthiness Information, or ``the MCAI''), to correct an 
unsafe condition for the specified products. The MCAI states:

    The shear pin in the input lever of several Pitch Feel 
Simulators (PFS) units has failed due to fatigue. The shear pin 
failure is not always detectable by the flight crew in normal 
operation. Failure of the shear pins in both PFS units on an 
aeroplane could result in loss of pitch feel forces and reduced 
controllability of the aeroplane.
    Recently, Transport Canada has certified the new design of the 
PFS unit--part number (P/N) 601R92300-7 as a terminating action. 
Revision 1 of this [Canadian] AD mandates the retrofit of all in-
service CL-600-2B19 aeroplanes with the redesigned PFS unit.

Required actions include revising the AWLs section of the Instructions 
for Continued Airworthiness, repetitive functional testing of the pilot 
input lever of the PFS unit, and corrective actions if necessary, and 
replacing the PFS units having part number (P/N) 601R92300-3 (vendor P/
N TY1910-50A) or 601R92300-5 (vendor P/N TY1910-51A) with PFS units 
having P/N 601R92300-7 (vendor P/N TY1910-54A), which terminates the 
actions required by AD 2008-08-09, Amendment 39-15461 (73 FR 19979, 
April 14, 2008). This AD also adds airplanes having serial numbers (S/
Ns) 7991 through 7999 inclusive, and removes airplanes having S/Ns 8111 
and subsequent. You may examine the MCAI in the AD docket on the 
Internet at http://www.regulations.gov/#!docketDetail;D=FAA-2013-0296.

Comments

    We gave the public the opportunity to participate in developing 
this AD. The following presents the comments received on the NPRM (78 
FR 21074, April 9, 2013) and the FAA's response to each comment.

Request To Revise the Applicability by Adding Part Numbers

    Air Wisconsin Airlines Corporation (Air Wisconsin) requested that 
we revise paragraph (c) of the proposed AD (78 FR 21074, April 9, 2013) 
by adding the part numbers of the PFS units, in addition to the 
airplane serial numbers. Air Wisconsin stated that the part numbers 
that should be added are P/N 601R92300-3 (vendor P/N TY1910-50A) and P/
N 601R92300-5 (vendor P/N TY1910-51A). Air Wisconsin provided no 
justification for this request.
    We do not agree to add the requested part numbers to the 
applicability of this AD. The functional check of the input lever 
required by this AD must be done on all airplanes having the serial 
numbers identified in the applicability of this AD. We have made no 
changes to paragraph (c) of this AD in this regard.

Request To Clarify Instructions Regarding Airworthiness Limitations

    Air Wisconsin requested that we clarify how an operator is to 
update the AWLs when the task for doing the functional test of the PFS 
unit was deleted. Air Wisconsin stated that paragraph (g) of the 
proposed AD (78 FR 21074, April 9, 2013) refers to Task R27-31-A024-01, 
which was deleted by Bombardier on February 23, 2007. Air Wisconsin 
pointed out that Task R27-31-A024-01 was specified in Bombardier 
Temporary Revision (TR) 2B-1784, dated October 24, 2003, to the 
Canadair CL-600-2B19 Regional Jet Maintenance Requirements Manual, Part 
2, Appendix B, which is no longer available or relevant.
    We agree. We removed proposed paragraph (g) (78 FR 21074, April 9, 
2013) from this AD, and redesignated subsequent paragraphs accordingly. 
The functional test specified in paragraph (h) of the proposed AD (78 
FR 21074, April 9, 2013) (redesignated as paragraph (g) of this AD) is 
now required in paragraph (g) of this AD.

Request To Revise Applicability To Exclude a Certain Serial Number

    Air Wisconsin requested that we revise paragraph (h) of the 
proposed AD (78 FR 21074, April 9, 2013) (redesignated as paragraph (g) 
of this AD) to match the Effectivity section of Bombardier Alert 
Service Bulletin A601R-27-144, Revision E, dated October 2, 2012. Air 
Wisconsin stated that paragraph (h) of the proposed AD applies to 
airplanes having S/Ns 7003 through 7990 inclusive, and S/Ns 8000 
through 8111 inclusive. Air Wisconsin stated that, while the 
Effectivity section of the service information varies between 
revisions, Bombardier Alert Service Bulletin A601R-27-144, Revision E, 
dated October 2, 2012, excludes the airplane having S/N 8111.
    We agree with Air Wisconsin's request to revise the applicability 
of this final rule for the reason provided. We have confirmed that the 
airplane having S/N 8111 is not affected by the unsafe condition 
addressed by this AD. Therefore, we have revised paragraphs (c) and (g) 
of this AD (designated as paragraphs (c) and (h) of the proposed AD (78 
FR 21074, April 9, 2013)) to remove the airplane having S/N 8111. We 
have coordinated this change with TCCA and Bombardier.

Request To Clarify Instructions Regarding Functional Test

    Air Wisconsin requested that we clarify how an operator is to 
perform the functional test identified in paragraph (j) of the proposed 
AD (78 FR 21074, April 9, 2013) (redesignated as paragraph (i) of this 
AD) when the task for the functional test has been deleted. Air 
Wisconsin stated that paragraph (j) of the proposed AD refers to Task 
R27-31-A024-01, which was deleted by Bombardier on February 23, 2007. 
Air Wisconsin stated that this task was specified in Bombardier TR 2B-
1784, dated October 24, 2003, to the Canadair CL-600-2B19 Regional Jet 
Maintenance Requirements Manual, Part 2, Appendix B, which is no longer 
available or relevant.
    We agree for the reason stated by Air Wisconsin. We have revised 
paragraph (i) of this AD (designated as paragraph (j) in the proposed 
AD (78 FR 21074, April 9, 2013)) by removing the reference to Task R27-
31-A024-01.

Request To Revise Wording in Paragraph (k) of the Proposed AD (78 FR 
21074, April 9, 2013)

    Air Wisconsin requested that the term ``detected'' in paragraph (k) 
of the proposed AD (78 FR 21074, April 9, 2013) (redesignated as 
paragraph (j) of

[[Page 41106]]

this AD) be changed to ``disconnected.'' Air Wisconsin asserted that 
FAA's intent was probably to use the term ``disconnected.''
    We partially agree. We agree that paragraph (j) of this AD (78 FR 
21074, April 9, 2013) (designated as paragraph (k) of the proposed AD) 
should read differently. Paragraph 2.B.(4)(c) of the Accomplishment 
Instructions of Bombardier Service Bulletin A601R-27-144, Revision E, 
dated October 2, 2012, states, ``If the input lever moves freely, or 
the input lever is loose, the PFS is ``defective. . . .'' Therefore, we 
have revised paragraphs (i) and (j) of this AD (designated as 
paragraphs (j) and (k) of the proposed AD) by changing the word 
``disconnected'' to ``defective.''

Request To Clarify Airplanes Affected by New PFS Unit Replacement

    Air Wisconsin requested that paragraph (l) of the proposed AD (78 
FR 21074, April 9, 2013) (redesignated as paragraph (k) of this AD) be 
revised to add vendor P/Ns TY1910-50A, TY1910-51A, and TY1910-54A for 
clarity.
    We agree with Air Wisconsin's request to add vendor part numbers in 
paragraph (k) of this AD (designated as paragraph (l) in the proposed 
AD (78 FR 21074, April 9, 2013). We have revised paragraph (k) of this 
AD by adding the vendor part numbers with the manufacturer part 
numbers.

Request To Add Compliance Time When Total Flight Hours are Unknown

    Air Wisconsin requested that paragraph (l) of the proposed AD (78 
FR 21074, April 9, 2013) (redesignated as paragraph (k) of this AD) be 
revised to add a replacement compliance time for PFS units on which the 
total flight hours are unknown. Air Wisconsin suggested the compliance 
time for PFS units with unknown total flight hours be 3,000 flight 
hours or 18 months after the effective date of this AD.
    We agree with Air Wisconsin's request to specify a compliance time 
for PFS units with unknown total flight hours. We have revised 
paragraph (k)(4) of this AD (78 FR 21074, April 9, 2013) to add the 
suggested compliance time for PFS units having P/N 601R92300-3 (vendor 
P/N TY1910-50A) or 601R92300-5 (vendor P/N TY1910-51A) for which the 
total flight hours are unknown or cannot be determined.

Explanation of Changes Made to This AD

    We have reformatted paragraph (l) of this AD (designated as 
paragraph (m) of the proposed AD (78 FR 21074, April 9, 2013).
    We have added new paragraph (l)(1) to this AD. Paragraph (l)(1) of 
this AD gives credit for doing a functional test if done before the 
effective date of AD 2006-05-11 R1, Amendment 39-14528 (71 FR 15323, 
March 28, 2006), using Bombardier Alert Service Bulletin A601R-27-144, 
including Appendix A, dated September 15, 2005.
    We redesignated paragraphs (m)(1), (m)(1)(i), (m)(1)(ii), and 
(m)(2) of the proposed AD (78 FR 21074, April 9, 2013) as paragraphs 
(l)(2), (l)(2)(i), (l)(2)(ii), and (l)(5) of this AD.

Conclusion

    We reviewed the available data, including the comments received, 
and determined that air safety and the public interest require adopting 
this AD with the changes described previously and minor editorial 
changes. We have determined that these changes:
    <bullet> Are consistent with the intent that was proposed in the 
NPRM (78 FR 21074, April 9, 2013) for correcting the unsafe condition; 
and
    <bullet> Do not add any additional burden upon the public than was 
already proposed in the NPRM (78 FR 21074, April 9, 2013).

Costs of Compliance

    We estimate that this AD affects 574 airplanes of U.S. registry.
    The actions that are required by AD 2008-08-09, Amendment 39-15461 
(73 FR 19979, April 14, 2008), and retained in this AD take about 2 
work-hours per product, at an average labor rate of $85 per work-hour. 
Required parts cost $0 per product. Based on these figures, the 
estimated cost of the actions that were required by AD 2008-08-09 is 
$170 per product.
    We also estimate that it will take about 8 work-hours per product 
to comply with the new basic requirements of this AD. The average labor 
rate is $85 per work-hour. Required parts will cost about $2,500 per 
product. Where the service information lists required parts costs that 
are covered under warranty, we have assumed that there will be no 
charge for these parts. As we do not control warranty coverage for 
affected parties, some parties may incur costs higher than estimated 
here. Based on these figures, we estimate the cost of this AD on U.S. 
operators to be $1,825,320, or $3,180 per product.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this AD will not have federalism implications 
under Executive Order 13132. This AD will not have a substantial direct 
effect on the States, on the relationship between the national 
government and the States, or on the distribution of power and 
responsibilities among the various levels of government.
    For the reasons discussed above, I certify that this AD:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov/#!docketDetail;D=FAA-2013-0296; or in person at the 
Docket Management Facility between 9 a.m. and 5 p.m., Monday through 
Friday, except Federal holidays. The AD docket contains this AD, the 
regulatory evaluation, any comments received, and other information. 
The street address for the Docket Operations office (telephone 800-647-
5527) is in the ADDRESSES section.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

[[Page 41107]]

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by removing Airworthiness Directive (AD) 
2008-08-09, Amendment 39-15461 (73 FR 19979, April 14, 2008), and 
adding the following new AD:


2014-11-10 Bombardier: Amendment 39-17861. Docket No. FAA-2013-0296; 
Directorate Identifier 2012-NM-102-AD.

(a) Effective Date

    This AD becomes effective August 19, 2014.

(b) Affected ADs

    This AD supersedes AD 2008-08-09, Amendment 39-15461 (73 FR 
19979, April 14, 2008).

(c) Applicability

    This AD applies to Bombardier, Inc. Model CL-600-2B19 (Regional 
Jet Series 100 & 440) airplanes, certificated in any category, 
serial numbers (S/Ns) 7003 through 8110 inclusive.

(d) Subject

    Air Transport Association (ATA) of America Code 27, Flight 
Controls.

(e) Reason

    This AD was prompted by reports that the shear pin in the input 
lever of several pitch feel simulator (PFS) units failed due to 
fatigue; and by the development of a re-designed PFS unit, which 
eliminates the need for repetitive functional testing. We are 
issuing this AD to prevent undetected failure of the shear pins of 
both PFS units simultaneously, which could result in loss of pitch 
feel forces and consequent reduced control of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Retained Functional Test of Input Lever With Revised Service 
Information

    This paragraph restates the requirements of paragraph (g) of AD 
2008-08-09, Amendment 39-15461 (73 FR 19979, April 14, 2008), with 
revised service information. For airplanes having S/Ns 7003 through 
7990 inclusive, and S/Ns 8000 through 8110 inclusive: Before the 
accumulation of 4,000 total flight hours, or within 100 flight hours 
after March 27, 2006 (the effective date of AD 2006-05-11 R1, 
Amendment 39-14528 (71 FR 15323, March 28, 2006), whichever occurs 
later, do a functional test of the pilot input lever of the PFS 
units to determine if the lever is disconnected, in accordance with 
the Accomplishment Instructions of a service bulletin specified in 
paragraph (g)(1), (g)(2), or (g)(3) of this AD. Repeat the test at 
intervals not to exceed 100 flight hours. As of the effective date 
of this AD, only Bombardier Alert Service Bulletin A601R-27-144, 
Revision E, dated October 2, 2012, including Appendix A, Revision A, 
dated December 20, 2006, may be used to accomplish the actions 
required by this paragraph.
    (1) Bombardier Alert Service Bulletin A601R-27-144, Revision A, 
dated February 14, 2006, including Appendix A, dated September 15, 
2005.
    (2) Bombardier Alert Service Bulletin A601R-27-144, Revision B, 
dated December 20, 2006, including Appendix A, Revision A, dated 
December 20, 2006.
    (3) Bombardier Alert Service Bulletin A601R-27-144, Revision E, 
dated October 2, 2012, including Appendix A, Revision A, dated 
December 20, 2006.

(h) Retained Replacement With Revised Service Information

    This paragraph restates the requirements of paragraph (h) of AD 
2008-08-09, Amendment 39-15461 (73 FR 19979, April 14, 2008), with 
revised service information. If any lever is found to be 
disconnected during any functional test required by paragraph (g) of 
this AD: Before further flight, replace the defective PFS unit with 
a serviceable PFS unit, in accordance with the Accomplishment 
Instructions of a service bulletin specified in paragraph (h)(1), 
(h)(2), or (h)(3) of this AD. As of the effective date of this AD, 
only Bombardier Alert Service Bulletin A601R-27-144, Revision E, 
dated October 2, 2012, including Appendix A, Revision A, dated 
December 20, 2006, may be used to accomplish the actions required by 
this paragraph.
    (1) Bombardier Alert Service Bulletin A601R-27-144, Revision A, 
dated February 14, 2006, including Appendix A, dated September 15, 
2005.
    (2) Bombardier Alert Service Bulletin A601R-27-144, Revision B, 
dated December 20, 2006, including Appendix A, Revision A, dated 
December 20, 2006.
    (3) Bombardier Alert Service Bulletin A601R-27-144, Revision E, 
dated October 2, 2012, including Appendix A, Revision A, dated 
December 20, 2006.

(i) New Functional Test of Input Lever

    For airplanes having S/Ns 7991 through 7999 inclusive: At the 
later of the times specified in paragraphs (i)(1) and (i)(2) of this 
AD, do a functional test of the pilot input lever of the PFS units 
to determine if the lever is defective, in accordance with the 
Accomplishment Instructions of Bombardier Alert Service Bulletin 
A601R-27-144, Revision E, dated October 2, 2012, including Appendix 
A, Revision A, dated December 20, 2006. Repeat the test thereafter 
at intervals not to exceed 100 flight hours.
    (1) Before the accumulation of 4,000 total flight hours.
    (2) Within 100 flight hours from the effective date of this AD.

(j) New Replacement of Defective Pitch Feel Simulator Unit

    For airplanes having S/Ns 7991 through 7999 inclusive: If any 
defective lever is found during any functional test required by 
paragraph (i) of this AD, before further flight, replace the 
defective PFS unit with a serviceable PFS unit, in accordance with 
the Accomplishment Instructions of Bombardier Alert Service Bulletin 
A601R-27-144, Revision E, dated October 2, 2012, including Appendix 
A, Revision A, dated December 20, 2006.

(k) New Replacement of Pitch Feel Simulator Units

    At the applicable time specified in paragraph (k)(1), (k)(2), 
(k)(3), or (k)(4) of this AD: Replace PFS units having part number 
(P/N) 601R92300-3 (vendor P/N TY1910-50A) or 601R92300-5 (vendor P/N 
TY1910-51A), with PFS units having P/N 601R92300-7 (vendor P/N 
TY1910-54A), in accordance with the Accomplishment Instructions of 
Bombardier Service Bulletin 601R-27-139, Revision A, dated May 28, 
2012. Accomplishment of the replacement required by this paragraph 
terminates the requirements of paragraphs (g), (h), (i), and (j) of 
this AD, and does not alter the approved maintenance program for the 
new redesigned PFS unit P/N 601R92300-7 (vendor P/N TY1910-54A).
    (1) For PFS units having P/N 601R92300-3 (vendor P/N TY1910-50A) 
or 601R92300-5 (vendor P/N TY1910-51A), that have accumulated less 
than 18,000 total flight hours as of the effective date of this AD: 
Within 6,000 flight hours after the effective date of this AD, but 
not to exceed 23,000 total flight hours on the PFS unit, or within 
36 months after the effective date of this AD, whichever occurs 
first.
    (2) For PFS units having P/N 601R92300-3 (vendor P/N TY1910-50A) 
or 601R92300-5 (vendor P/N TY1910-51A), that have accumulated more 
than or equal to 18,000 total flight hours, but less than 19,000 
total flight hours as of the effective date of this AD: Within 5,000 
flight hours after the effective date of this AD, but not to exceed 
23,000 total flight hours on the PFS unit, or within 30 months after 
the effective date of this AD, whichever occurs first.
    (3) For PFS units having P/N 601R92300-3 (vendor P/N TY1910-50A) 
or 601R92300-5 (vendor P/N TY1910-51A), that have accumulated more 
than or equal to 19,000 total flight hours, but less than 20,000 
total flight hours as of the effective date of this AD: Within 4,000 
flight hours after the effective date of this AD, but not to exceed 
23,000 total flight hours on the PFS unit, or within 24 months after 
the effective date of this AD, whichever occurs first.
    (4) For PFS units having P/N 601R92300-3 (vendor P/N TY1910-50A) 
or 601R92300-5 (vendor P/N TY1910-51A) that have accumulated more 
than or equal to 20,000 total flight hours as of the effective date 
of this AD, or for which the total flight hours are unknown or 
cannot be determined: Within 3,000 flight hours or 18 months after 
the effective date of this AD, whichever occurs first.

(l) Credit for Previous Actions

    (1) This paragraph provides credit for the actions required by 
paragraphs (g) and (h) of this AD, if those actions were performed 
before March 27, 2006 (the effective date of AD 2006-05-11 R1, 
Amendment 39-14528

[[Page 41108]]

(71 FR 15323, March 28, 2006)), using Bombardier Alert Service 
Bulletin A601R-27-144, including Appendix A, dated September 15, 
2005, which is not incorporated by reference in this AD.
    (2) This paragraph provides credit for the actions required by 
paragraphs (g) and (h) of this AD, if those actions were performed 
before the effective date of this AD using a service bulletin 
identified in paragraph (l)(2)(i) or (l)(2)(ii) of this AD.
    (i) Bombardier Alert Service Bulletin A601R-27-144, Revision C, 
dated July 21, 2008, including Appendix A, dated December 20, 2006, 
which is not incorporated by reference in this AD.
    (ii) Bombardier Alert Service Bulletin A601R-27-144, Revision D, 
dated December 22, 2011, including Appendix A, dated December 20, 
2006, which is not incorporated by reference in this AD.
    (3) This paragraph provides credit for the actions required by 
paragraph (h) of this AD, if those actions were performed before 
March 27, 2006 (the effective date of AD 2006-05-11 R1, Amendment 
39-14528 (71 FR 15323, March 28, 2006)), using Bombardier Alert 
Service Bulletin A601R-27-144, Revision B, dated December 20, 2006, 
including Appendix A, Revision A, dated December 20, 2006.
    (4) This paragraph provides credit for actions required by 
paragraph (i) of this AD, if those actions were performed before May 
19, 2008 (the effective date of AD 2008-08-09, Amendment 39-15461 
(73 FR 19979, April 14, 2008)), using Bombardier Alert Service 
Bulletin A601R-27-144, Revision B, dated December 20, 2006, 
including Appendix A, Revision A, dated December 20, 2006.
    (5) This paragraph provides credit for replacement of the PFS 
units required by paragraph (k) of this AD, if those actions were 
performed before the effective date of this AD using Bombardier 
Service Bulletin 601R-27-139, dated December 22, 2011, which is not 
incorporated by reference in this AD.

(m) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, New 
York Aircraft Certification Office (ACO), ANE-170, FAA, has the 
authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. Send information to ATTN: 
Program Manager, Continuing Operational Safety, FAA, New York ACO, 
1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 516-
228-7300; fax 516-794-5531. Before using any approved AMOC, notify 
your appropriate principal inspector, or lacking a principal 
inspector, the manager of the local flight standards district 
office/certificate holding district office. The AMOC approval letter 
must specifically reference this AD. AMOCs approved previously in 
accordance with AD 2008-08-09, Amendment 39-15461 (73 FR 19979, 
April 14, 2008), are approved as AMOCs for the corresponding actions 
specified in paragraphs (g) and (h) of this AD.
    (2) Airworthy Product: For any requirement in this AD to obtain 
corrective actions from a manufacturer or other source, use these 
actions if they are FAA-approved. Corrective actions are considered 
FAA-approved if they are approved by the State of Design Authority 
(or their delegated agent). You are required to assure the product 
is airworthy before it is returned to service.

(n) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information 
(MCAI) Canadian Airworthiness Directive CF-2005-41R1, dated May 10, 
2012, for related information. You may examine the MCAI in the AD 
docket on the Internet at http://www.regulations.gov/#!docketDetail;D=FAA-2013-0296.
    (2) Service information identified in this AD that is not 
incorporated by reference may be obtained at the addresses specified 
in paragraphs (o)(3) and (o)(4) of this AD.

(o) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) Bombardier Alert Service Bulletin A601R-27-144, Revision E, 
dated October 2, 2012, including Appendix A, Revision A, dated 
December 20, 2006.
    (ii) Bombardier Service Bulletin 601R-27-139, Revision A, dated 
May 28, 2012.
    (3) For service information identified in this AD, contact 
Bombardier, Inc., 400 C[ocirc]te-Vertu Road West, Dorval, 
Qu[eacute]bec H4S 1Y9, Canada; telephone 514-855-5000; fax 514-855-
7401; email [email protected]; Internet http://www.bombardier.com.
    (4) You may view this referenced service information at the FAA, 
Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. 
For information on the availability of this material at the FAA, 
call 425-227-1221.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued in Renton, Washington, on May 27, 2014.
Michael Kaszycki,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2014-15655 Filed 7-14-14; 8:45 am]
BILLING CODE 4910-13-P

The complete text was extracted from the official GovInfo HTML edition for this publication. Acquired 2026-10-09T02:47:12.785483+00:00. Text extraction preserves the recorded source wording; it does not determine current requirements.

Open the captured official edition

Source SHA-256

6f33769afbcad5144abfb1e9b90bb16dacf1f4bd06020d35d87bade5e49e44c0

Text SHA-256

6b8acce60b574480b5b024d3c36890144884ed56abe7b44497c2c291700675a6