Airworthiness Directives; Bombardier, Inc. Airplanes

[Federal Register Volume 79, Number 239 (Friday, December 12, 2014)]
[Rules and Regulations]
[Pages 73812-73813]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2014-28924]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2014-0567; Directorate Identifier 2014-NM-124-AD; 
Amendment 39-18043; AD 2014-25-02]
RIN 2120-AA64


Airworthiness Directives; Bombardier, Inc. Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for certain 
Bombardier, Inc. Model CL-600-2B19 (Regional Jet Series 100 & 440) 
airplanes. This AD was prompted by issuance of revised certification 
maintenance requirements for the horizontal stabilizer trim actuator 
(HSTA). This AD requires revising the maintenance or inspection 
program. We are issuing this AD to detect and correct premature wear 
and cracking of the HSTAs, which could result in reduced structural 
integrity and reduced control of the airplane due to the failure of 
system components.

DATES: This AD becomes effective January 16, 2015.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of January 16, 
2015.

ADDRESSES: You may examine the AD docket on the Internet at http://www.regulations.gov/#!documentDetail;D=FAA-2014-0567 or in person at 
the Docket Management Facility, U.S. Department of Transportation, 
Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 
New Jersey Avenue SE., Washington, DC.
    For service information identified in this AD, contact Bombardier, 
Inc., 400 C[ocirc]te-Vertu Road West, Dorval, Qu[eacute]bec H4S 1Y9, 
Canada; telephone 514-855-5000; fax 514-855-7401; email 
[email protected]; Internet http://www.bombardier.com. You 
may view this referenced service information at the FAA, Transport 
Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information 
on the availability of this material at the FAA, call 425-227-1221.

FOR FURTHER INFORMATION CONTACT: Cesar Gomez, Aerospace Engineer, 
Airframe and Mechanical Systems Branch, ANE-171, FAA, New York Aircraft 
Certification Office, 1600 Stewart Avenue, Suite 410, Westbury, NY 
11590; telephone 516-228-7318; fax 516-794-5531.

SUPPLEMENTARY INFORMATION:

Discussion

    We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR 
part 39 by adding an AD that would apply to certain Bombardier, Inc. 
Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes. The NPRM 
published in the Federal Register on August 14, 2014 (79 FR 47594).
    Transport Canada Civil Aviation (TCCA), which is the aviation 
authority for Canada, has issued Canadian Airworthiness Directive CF-
2014-13, dated April 17, 2014 (referred to after this as the Mandatory 
Continuing Airworthiness Information, or ``the MCAI''), to correct an 
unsafe condition for certain Bombardier, Inc. Model CL-600-2B19 
(Regional Jet Series 100 & 440) airplanes. The MCAI states:

    A revision has been made to Part 2 of the Canadair Regional Jet 
Maintenance Requirements Manual (MRM), Appendix A--Certification 
Maintenance Requirements [CMR] which introduces a new task for the 
HSTA. Failure to comply with the CMR task could lead to an unsafe 
condition.
    This [Canadian] AD is issued to ensure that premature wear and 
cracking of the affected components are detected and corrected. 
[This condition could result in reduced structural integrity and 
reduced control of the airplane due to the failure of system 
components.]

    You may examine the MCAI in the AD docket on the Internet at http://www.regulations.gov/#!documentDetail;D=FAA-2014-0567-0002.

Comments

    We gave the public the opportunity to participate in developing 
this AD. We received no comments on the NPRM (79 FR 47594, August 14, 
2014) or on the determination of the cost to the public.

Conclusion

    We reviewed the relevant data and determined that air safety and 
the public interest require adopting this AD as proposed except for 
minor editorial changes. We have determined that these minor changes:
    <bullet> Are consistent with the intent that was proposed in the 
NPRM (79 FR 47594, August 14, 2014) for correcting the unsafe 
condition; and
    <bullet> Do not add any additional burden upon the public than was 
already proposed in the NPRM (79 FR 47594, August 14, 2014).

Costs of Compliance

    We estimate that this AD affects 416 airplanes of U.S. registry.
    We also estimate that it will take about 1 work-hour per product to 
comply with the basic requirements of this AD. The average labor rate 
is $85 per work-hour. Required parts will cost about $0 per product. 
Based on these figures, we estimate the cost of this AD on U.S. 
operators to be $35,360, or $85 per product.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this AD will not have federalism implications 
under Executive Order 13132. This AD will not have a substantial direct 
effect on the States, on the relationship between the national 
government and the States, or on the distribution of power and 
responsibilities among the various levels of government.
    For the reasons discussed above, I certify that this AD:

[[Page 73813]]

    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov/#!docketDetail;D=FAA-2014-0567; or in person at the 
Docket Management Facility between 9 a.m. and 5 p.m., Monday through 
Friday, except Federal holidays. The AD docket contains this AD, the 
regulatory evaluation, any comments received, and other information. 
The street address for the Docket Operations office (telephone 800-647-
5527) is in the ADDRESSES section.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

2014-25-02 Bombardier, Inc.: Amendment 39-18043. Docket No. FAA-
2014-0567; Directorate Identifier 2014-NM-124-AD.

(a) Effective Date

    This AD becomes effective January 16, 2015.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Bombardier, Inc. Model CL-600-2B19 (Regional 
Jet Series 100 & 440) airplanes, certificated in any category, 
equipped with horizontal stabilizer trim actuator (HSTA) part number 
(P/N) 601R92305-7 (vendor P/N 8396-5).

(d) Subject

    Air Transport Association (ATA) of America Code 55, Stabilizers.

(e) Reason

    This AD was prompted by issuance of revised certification 
maintenance requirements (CMR) for the HSTA. We are issuing this AD 
to detect and correct premature wear and cracking of certain HSTAs, 
which could result in reduced structural integrity and reduced 
control of the airplane due to the failure of system components.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Maintenance or Inspection Program Revision

    Within 30 days after the effective date of this AD, revise the 
maintenance or inspection program, as applicable, to incorporate the 
information specified in Task C27-40-103-05, ``Restoration 
(Overhaul) of the HSTA,'' of Bombardier Temporary Revision (TR) 2A-
58, dated January 31, 2014, into Appendix A--Certification 
Maintenance Requirements (CMR), of Part 2, of the Bombardier CL-600-
2B19 Maintenance Requirements Manual (MRM). The initial compliance 
time for accomplishing Task C27-40-103-05, ``Restoration (Overhaul) 
of the HSTA,'' of Bombardier Temporary Revision (TR) 2A-58, dated 
January 31, 2014, is at the applicable phase-in time specified in 
Bombardier TR 2A-58, dated January 31, 2014, or within 30 days after 
the effective date of this AD, whichever occurs later. The revision 
required by paragraph (g) of this AD may be done by inserting a copy 
of Bombardier TR 2A-58, dated January 31, 2014, into Appendix A--
CMR, of Part 2 of the Bombardier CL-600-2B19 MRM. When Bombardier TR 
2A-58, dated January 31, 2014, has been included in the general 
revisions of the Bombardier CL-600-2B19 MRM, the general revisions 
may be inserted into the MRM, provided the relevant information in 
the general revision is identical to that in Bombardier TR 2A-58, 
dated January 31, 2014.

(h) No Alternative Actions and Intervals

    After accomplishing the revision required by paragraph (g) of 
this AD, no alternative actions (e.g., inspections) or intervals may 
be used unless the actions or intervals are approved as an 
alternative method of compliance (AMOC) in accordance with the 
procedures specified in paragraph (i)(1) of this AD.

(i) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, New 
York Aircraft Certification Office (ACO), ANE-170, FAA, has the 
authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the ACO, send it to Program Manager, Continuing 
Operational Safety, FAA, New York ACO, 1600 Stewart Avenue, Suite 
410, Westbury, NY 11590; telephone 516-228-7300; fax 516-794-5531. 
Before using any approved AMOC, notify your appropriate principal 
inspector, or lacking a principal inspector, the manager of the 
local flight standards district office/certificate holding district 
office. The AMOC approval letter must specifically reference this 
AD.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain corrective actions from a manufacturer, the action must be 
accomplished using a method approved by the Manager, New York ACO, 
ANE-170, Engine and Propeller Directorate, FAA; or Transport Canada 
Civil Aviation (TCCA); or Bombardier, Inc.'s TCCA Design Approval 
Organization (DAO). If approved by the DAO, the approval must 
include the DAO-authorized signature.

(j) Related Information

    Refer to Mandatory Continuing Airworthiness Information (MCAI) 
Canadian Airworthiness Directive CF-2014-13, dated April 17, 2014, 
for related information. This MCAI may be found in the AD docket on 
the Internet at http://www.regulations.gov by searching for and 
locating Docket No. FAA-2014-0567.

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) Bombardier Temporary Revision 2A-58, dated January 31, 2014, 
to Appendix A--Certification Maintenance Requirements, of Part 2 of 
the Bombardier CL-600-2B19 Maintenance Requirements Manual.
    (ii) Reserved.
    (3) For service information identified in this AD, contact 
Bombardier, Inc., 400 C[ocirc]te-Vertu Road West, Dorval, 
Qu[eacute]bec H4S 1Y9, Canada; telephone 514-855-5000; fax 514-855-
7401; email [email protected]; Internet http://www.bombardier.com.
    (4) You may view this service information at the FAA, Transport 
Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For 
information on the availability of this material at the FAA, call 
425-227-1221.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued in Renton, Washington, on November 28, 2014.
John P. Piccola, Jr.,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2014-28924 Filed 12-11-14; 8:45 am]
BILLING CODE 4910-13-P

The complete text was extracted from the official GovInfo HTML edition for this publication. Acquired 2026-10-09T02:36:13.126687+00:00. Text extraction preserves the recorded source wording; it does not determine current requirements.

Open the captured official edition

Source SHA-256

c7ccedebf1d2bdff10bd535d2df99d3fddf2eb5b30061663f8b16e5a2430ca2e

Text SHA-256

53e41aca53cd4ccd95bc16a2e76bae3756f79c44a2cafa8799cbdd8bb0830803