Airworthiness Directives; Airbus Airplanes

[Federal Register Volume 82, Number 124 (Thursday, June 29, 2017)]
[Rules and Regulations]
[Pages 29363-29368]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2017-13407]



========================================================================
Rules and Regulations
                                                Federal Register
________________________________________________________________________

This section of the FEDERAL REGISTER contains regulatory documents 
having general applicability and legal effect, most of which are keyed 
to and codified in the Code of Federal Regulations, which is published 
under 50 titles pursuant to 44 U.S.C. 1510.

The Code of Federal Regulations is sold by the Superintendent of Documents. 

========================================================================


Federal Register / Vol. 82, No. 124 / Thursday, June 29, 2017 / Rules 
and Regulations

[[Page 29363]]



DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2016-9573; Directorate Identifier 2016-NM-149-AD; 
Amendment 39-18938; AD 2017-13-08]
RIN 2120-AA64


Airworthiness Directives; Airbus Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We are superseding Airworthiness Directive (AD) 2015-23-13, 
for all Airbus Model A318 and A319 series airplanes, Model A320-211, -
212, -214, -231, -232, and -233 airplanes, and Model A321-111, -112, -
131, -211, -212, -213, -231, and -232 airplanes. AD 2015-23-13 required 
modification of the pin programming of the flight warning computer 
(FWC) to activate the stop rudder input warning (SRIW) logic; and an 
inspection to determine the part numbers of the FWC and the flight 
augmentation computer (FAC), and replacement of the FWC and FAC if 
necessary. This new AD, for certain airplanes, also requires 
accomplishment of additional modification instructions to install the 
minimum FWC and FAC configuration compatible with SRIW activation. This 
AD was prompted by a determination that, in specific flight conditions, 
the allowable load limits on the vertical tail plane could be reached 
and possibly exceeded. We are issuing this AD to address the unsafe 
condition on these products.

DATES: This AD is effective August 3, 2017.
    The Director of the Federal Register approved the incorporation by 
reference of certain publications listed in this AD as of August 3, 
2017.
    The Director of the Federal Register approved the incorporation by 
reference of certain other publications listed in this AD as of 
December 29, 2015 (80 FR 73099, November 24, 2015).

ADDRESSES: For service information identified in this final rule, 
contact Airbus, Airworthiness Office--EIAS, 1 Rond Point Maurice 
Bellonte, 31707 Blagnac Cedex, France; telephone +33 5 61 93 36 96; fax 
+33 5 61 93 44 51; email [email protected]; Internet 
http://www.airbus.com. You may view this referenced service information 
at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., 
Renton, WA. For information on the availability of this material at the 
FAA, call 425-227-1221. It is also available on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2016-
9573.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2016-
9573; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this AD, the regulatory evaluation, any comments received, and 
other information. The address for the Docket Office (telephone 800-
647-5527) is Docket Management Facility, U.S. Department of 
Transportation, Docket Operations, M-30, West Building Ground Floor, 
Room W12-140, 1200 New Jersey Avenue SE., Washington, DC 20590.

FOR FURTHER INFORMATION CONTACT: Sanjay Ralhan, Aerospace Engineer, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
1601 Lind Avenue SW., Renton, WA 98057-3356; telephone 425-227-1405; 
fax 425-227-1149.

SUPPLEMENTARY INFORMATION:

Discussion

    We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR 
part 39 to supersede AD 2015-23-13, Amendment 39-18330 (80 FR 73099, 
November 24, 2015) (``AD 2015-23-13''). AD 2015-23-13 applied to all 
Airbus Model A318 and A319 series airplanes, Model A320-211, -212, -
214, -231, -232, and -233 airplanes, and Model A321-111, -112, -131, -
211, -212, -213, -231, and -232 airplanes. The NPRM published in the 
Federal Register on February 15, 2017 (82 FR 10721) (``the NPRM''). The 
NPRM was prompted by a determination that, for certain airplanes, 
additional modification instructions must be accomplished to allow 
installation of the minimum FWC and FAC configuration compatible with 
SRIW activation. The NPRM proposed to continue to require modification 
of the pin programming of the FWC to activate the SRIW logic; and an 
inspection to determine the part numbers of the FWC and the FAC, and 
replacement of the FWC and FAC if necessary. The NPRM also proposed, 
for certain airplanes, to also require accomplishment of additional 
modification instructions to install the minimum FWC and FAC 
configuration compatible with SRIW activation. We are issuing this AD 
to prevent detachment of the vertical tail plane and consequent loss of 
control of the airplane.
    The European Aviation Safety Agency (EASA), which is the Technical 
Agent for the Member States of the European Union, has issued EASA 
Airworthiness Directive 2016-0132, dated July 5, 2016; corrected July 
20, 2016 (referred to after this as the Mandatory Continuing 
Airworthiness Information, or ``the MCAI''), to correct an unsafe 
condition for all Airbus Model A318 and A319 series airplanes, Model 
A320-211, -212, -214, -231, -232, and -233 airplanes, and Model A321-
111, -112, -131, -211, -212, -213, -231, and -232 airplanes. The MCAI 
states:

    During design reviews that were conducted following safety 
recommendations related to in-service incidents and one accident on 
another aircraft type, it has been determined that, in specific 
flight conditions, the allowable load limits on the vertical tail 
plane could be reached and possibly exceeded.
    This condition, if not corrected, could lead to in-flight 
detachment of the vertical tail plane, possibly resulting in loss of 
control of the aeroplane.
    To address this unsafe condition, Airbus developed modifications 
within the flight augmentation computer (FAC) to reduce the vertical 
tail plane stress and to activate a conditional aural warning within 
the flight warning computer (FWC) to further protect against pilot 
induced rudder doublets.
    Consequently, EASA issued AD 2014-0217 (later revised) [which 
corresponds to FAA AD 2015-23-13] to require installation and 
activation of the stop rudder input warning (SRIW) logic. In 
addition, that [EASA] AD

[[Page 29364]]

required upgrades of the FAC and FWC, to introduce the SRIW logic 
and SRIW aural capability, respectively. After modification, the 
[EASA] AD prohibited (re)installation of certain Part Number (P/N) 
FWC and FAC.
    Since EASA AD 2014-0217R1 was issued, Airbus made available 
additional modification instructions that, for certain aeroplanes, 
must be accomplished to allow installation of the minimum FWC and 
FAC configuration compatible with SRIW activation.
    For the reasons described above, this [EASA] AD retains the 
requirements of EASA AD 2014-0217R1, which is superseded, and 
includes reference to modification instructions, which must be 
accomplished on certain aeroplanes.
    This [EASA] AD is republished to remove a typographical error in 
Appendix 1 [of the EASA AD].

    You may examine the MCAI in the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2016-
9573.

Comments

    We gave the public the opportunity to participate in developing 
this AD. The following presents the comments received on the NPRM and 
the FAA's response to each comment.

Request for Technical Details

    Mr. Geoffrey Barrance stated that the public disclosure in the NPRM 
did not provide sufficient technical details and disclosure relative to 
the unsafe condition; and that, presumably, the actions required by 
this proposed AD are to improve the protection provided by the SRIW 
logic. Mr. Barrance noted that the purpose of publication in the 
Federal Register is to provide public disclosure. We infer the 
commenter is requesting that we provide additional technical details.
    We do not agree with the commenter's request. The technical details 
associated with correcting the unsafe condition were already provided 
in the previously published AD, AD 2015-23-13. That AD and all service 
information that was incorporated by reference in AD 2015-23-13 is 
posted on the public docket in the Federal Docket Management System and 
is available on the Internet at http://www.regulations.gov by searching 
for and locating Docket No. FAA-2015-0251. This superseding AD only 
mandates accomplishment of additional modification instructions to 
ensure design compatibility. We have not revised this AD in this 
regard.

Request for Review of Design Approval Process and Compliance Time 
Determination

    Mr. Geoffrey Barrance asserted that this rulemaking action is a 
result of failure of design, development, oversight and approval 
processes at the EASA and the FAA. Mr. Barrance asserted that the FAA 
must do a comprehensive review of these processes and evaluate the 
extent that the flying public has been exposed to risks due to delayed 
processes in releasing this AD.
    We do not agree with Mr. Geoffrey Barrance's comments. Mr. Barrance 
has submitted no data to substantiate his claims. This rulemaking 
action simply supersedes a previous AD in order to mandate 
accomplishment of additional modification instructions to ensure design 
compatibility. Furthermore, we and our bilateral partner, EASA, work 
closely with Airbus to ensure that design solutions are certificated 
based on applicable airworthiness regulations prior to mandating those 
solutions to mitigate safety risks. We also ensure that all appropriate 
instructions and parts are available at the appropriate time to comply 
with AD requirements. As a component of our safety management system, 
we continuously evaluate our certification system and procedures and 
improve them when problems are found. We have not revised this AD in 
this regard.

Request for Compliance Time Review

    The Air Line Pilots Association, International (ALPA) stated that 
it agrees with the NPRM, but requested that we revisit the compliance 
timeframe to ensure it is aligned with the intent of the AD.
    The EASA has determined the compliance times based on the overall 
risk to the fleet, including the severity of the failure and the 
likelihood of the failure's occurrence. The FAA and EASA worked with 
Airbus to ensure that all appropriate action(s) are taken at 
appropriate times to mitigate the risk to the fleet. We have not 
changed this AD in this regard.

Request for Correction of Typographical Error

    Jetblue Airways (Jetblue) requested that we correct a typographical 
error in paragraph (i)(10) of the NPRM. Jetblue stated that it should 
be ``FWC H2-F7,'' not ``FWC H-F7.''
    We agree with the commenter's request and have revised this AD 
accordingly.

Request for an Alternative Method of Compliance (AMOC)

    Jetblue requested that we include an AMOC for FWC standard H2-F9D 
(P/N 350E053021818) in this AD.
    We do not agree to include an AMOC in this AD because certain later 
approved parts are already addressed in paragraph (l) of this AD. To 
clarify, FWCs approved after March 5, 2015, are an approved method of 
compliance with the requirements of paragraph (h) or (j) of this AD, 
provided the requirements specified in paragraphs (l)(1) and (l)(2) of 
this AD are met. We have not changed this AD in this regard.

Conclusion

    We reviewed the available data, including the comments received, 
and determined that air safety and the public interest require adopting 
this AD with the change described previously and minor editorial 
changes. We have determined that these changes:
    <bullet> Are consistent with the intent that was proposed in the 
NPRM for correcting the unsafe condition; and
    <bullet> Do not add any additional burden upon the public than was 
already proposed in the NPRM.

Related Service Information Under 1 CFR Part 51

    Airbus has issued Service Bulletin A320-22-1480, Revision 02, dated 
March 30, 2015, and Service Bulletin A320-22-1480, Revision 03, dated 
October 13, 2015. This service information describes procedures for 
modifying the pin programming to activate the SRIW logic. These 
documents are distinct due to editorial revisions.
    Airbus has also issued the following service information. The 
service information describes procedures for replacing FWCs and FACs. 
These documents are distinct since they apply to different airplane 
configurations and software packages.
    <bullet> Airbus Service Bulletin A320-22-1375, dated January 15, 
2014.
    <bullet> Airbus Service Bulletin A320-22-1427, Revision 05, 
including Appendix 01, dated November 24, 2014.
    <bullet> Airbus Service Bulletin A320-22-1447, Revision 03, dated 
April 21, 2015.
    <bullet> Airbus Service Bulletin A320-22-1454, dated February 12, 
2014.
    <bullet> Airbus Service Bulletin A320-22-1461, Revision 07, 
including Appendix 01, dated March 23, 2015.
    <bullet> Airbus Service Bulletin A320-22-1502, dated November 14, 
2014.
    <bullet> Airbus Service Bulletin A320-22-1539, Revision 01, dated 
February 24, 2016.
    <bullet> Airbus Service Bulletin A320-22-1553, dated March 21, 
2016.
    <bullet> Airbus Service Bulletin A320-22-1554, dated April 19, 
2016.
    <bullet> Airbus Service Bulletin A320-31-1414, Revision 03, dated 
September 15, 2014.
    This service information is reasonably available because the 
interested parties

[[Page 29365]]

have access to it through their normal course of business or by the 
means identified in the ADDRESSES section.

Costs of Compliance

    We estimate that this AD will affect 1,032 airplanes of U.S. 
registry.
    The actions required by AD 2015-23-13, and retained in this AD take 
about 3 work-hours per product, at an average labor rate of $85 per 
work-hour. Based on these figures, the estimated cost of the actions 
that are required by AD 2015-23-13 is $255 per product.
    We also estimate that it would take about 3 work-hours per product 
to comply with the basic requirements of this AD. The average labor 
rate is $85 per work-hour. Based on these figures, we estimate the cost 
of this AD on U.S. operators to be $263,160, or $255 per product.
    In addition, we estimate that any necessary follow-on actions will 
take about 6 work-hours (3 work-hours for an FWC and 3 work-hours for 
an FAC), and require parts costing $88,000 (FAC), for a cost of $88,510 
per product. We have no way of determining the number of aircraft that 
might need these actions.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this AD will not have federalism implications 
under Executive Order 13132. This AD will not have a substantial direct 
effect on the States, on the relationship between the national 
government and the States, or on the distribution of power and 
responsibilities among the various levels of government.
    For the reasons discussed above, I certify that this AD:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by removing Airworthiness Directive (AD) 
2015-23-13, Amendment 39-18330 (80 FR 73099, November 24, 2015), and 
adding the following new AD:

2017-13-08 Airbus: Amendment 39-18938; Docket No. FAA-2016-9573; 
Directorate Identifier 2016-NM-149-AD.

(a) Effective Date

    This AD is effective August 3, 2017.

(b) Affected ADs

    This AD replaces AD 2015-23-13, Amendment 39-18330 (80 FR 73099, 
November 24, 2015) (``AD 2015-23-13'').

(c) Applicability

    This AD applies to the airplanes identified in paragraphs (c)(1) 
through (c)(4) of this AD, certificated in any category, all 
manufacturer serial numbers.
    (1) Airbus Model A318-111, -112, -121, and -122 airplanes.
    (2) Airbus Model A319-111, -112, -113, -114, -115, -131, -132, 
and -133 airplanes.
    (3) Airbus Model A320-211, -212, -214, -231, -232, and -233 
airplanes.
    (4) Airbus Model A321-111, -112, -131, -211, -212, -213, -231, 
and -232 airplanes.

(d) Subject

    Air Transport Association (ATA) of America Code 22, Auto Flight; 
31, Instruments.

(e) Reason

    This AD was prompted by a determination that, in specific flight 
conditions, the allowable load limits on the vertical tail plane 
could be reached and possibly exceeded. Exceeding allowable load 
limits could result in detachment of the vertical tail plane. We are 
issuing this AD to prevent detachment of the vertical tail plane and 
consequent loss of control of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Retained Pin Programming Modification, With New Service Information

    This paragraph restates the requirements of paragraph (g) of AD 
2015-23-13, with new service information. Within 48 months after 
December 29, 2015 (the effective date of AD 2015-23-13), modify the 
pin programming to activate the stop rudder input warning (SRIW) 
logic, in accordance with the Accomplishment Instructions of Airbus 
Service Bulletin A320-22-1480, Revision 02, dated March 30, 2015; or 
Airbus Service Bulletin A320-22-1480, Revision 03, dated October 13, 
2015. As of the effective date of this AD, use only Airbus Service 
Bulletin A320-22-1480, Revision 03, dated October 13, 2015.

(h) Retained Inspection To Determine Part Numbers (P/Ns), Flight 
Warning Computer (FWC) and Flight Augmentation Computer (FAC) 
Replacement, With New Replacement Part Numbers

    This paragraph restates the requirements of paragraph (h) of AD 
2015-23-13, with new replacement part numbers. Prior to or 
concurrently with the actions required by paragraph (g) of this AD: 
Inspect the part numbers of the FWC and the FAC installed on the 
airplane. If any FWC or FAC having a part number identified in 
paragraph (h)(1) or (h)(2) of this AD, as applicable, is installed 
on an airplane, prior to or concurrently with the actions required 
by paragraph (g) of this AD, replace all affected FWCs and FACs with 
a unit having a part number identified in figure 1 to paragraph 
(h)(3) of this AD, in accordance with the Accomplishment 
Instructions of the applicable Airbus service information specified 
in paragraph (i) of this AD. As of the effective date of this AD, 
use only figure 1 to paragraph (h)(3) of this AD to identify the 
replacement part numbers.
    (1) Paragraphs (h)(1)(i) through (h)(1)(xvii) of this AD 
identify FWCs having part numbers that are non-compatible with the 
SRIW activation required by paragraph (g) of this AD.
    (i) 350E017238484 (H1-D1).
    (ii) 350E053020303 (H2-E3).
    (iii) 350E016187171 (C5).
    (iv) 350E053020404 (H2-E4).
    (v) 350E017248685 (H1-D2).
    (vi) 350E053020606 (H2-F2).
    (vii) 350E017251414 (H1-E1).
    (viii) 350E053020707 (H2-F3).
    (ix) 350E017271616 (H1-E2).
    (x) 350E053021010 (H2-F3P).
    (xi) 350E018291818 (H1-E3CJ).
    (xii) 350E053020808 (H2-F4).
    (xiii) 350E018301919 (H1-E3P).
    (xiv) 350E053020909 (H2-F5).
    (xv) 350E018312020 (H1-E3Q).
    (xvi) 350E053021111 (H2-F6).
    (xvii) 350E053020202 (H2-E2).

[[Page 29366]]

    (2) Paragraphs (h)(2)(i) through (h)(2)(xxxiv) of this AD 
identify FACs having part numbers that are non-compatible with the 
SRIW activation required by paragraph (g) of this AD.
    (i) B397AAM0202.
    (ii) B397BAM0101.
    (iii) B397BAM0512.
    (iv) B397AAM0301.
    (v) B397BAM0202.
    (vi) B397BAM0513.
    (vii) B397AAM0302.
    (viii) B397BAM0203.
    (ix) B397BAM0514.
    (x) B397AAM0303.
    (xi) B397BAM0305.
    (xii) B397BAM0515.
    (xiii) B397AAM0404.
    (xiv) B397BAM0406.
    (xv) B397BAM0616.
    (xvi) B397AAM0405.
    (xvii) B397BAM0407.
    (xviii) B397BAM0617.
    (xix) B397AAM0506.
    (xx) B397BAM0507.
    (xxi) B397BAM0618.
    (xxii) B397AAM0507.
    (xxiii) B397BAM0508.
    (xxiv) B397BAM0619.
    (xxv) B397AAM0508.
    (xxvi) B397BAM0509.
    (xxvii) B397BAM0620.
    (xxviii) B397AAM0509.
    (xxix) B397BAM0510.
    (xxx) B397CAM0101.
    (xxxi) B397AAM0510.
    (xxxii) B397BAM0511.
    (xxxiii) B397CAM0102.
    (xxxiv) Soft P/N G2856AAA01 installed on hard P/N C13206AA00.
    (3) As of the effective date of this AD, figure 1 to paragraph 
(h)(3) of this AD identifies the FACs and FWCs having the part 
numbers that are compatible with SRIW activation required by 
paragraph (g) of this AD.
BILLING CODE 4910-13-P
[GRAPHIC] [TIFF OMITTED] TR29JN17.000


[[Page 29367]]


BILLING CODE 4910-13-C

(i) Retained Service Information for Actions Required by Paragraph (h) 
of This AD, With New Service Information

    This paragraph restates the requirements of paragraph (i) of AD 
2015-23-13, with new service information. Do the actions required by 
paragraph (h) of this AD in accordance with the Accomplishment 
Instructions of the applicable Airbus service information specified 
in paragraphs (i)(1) through (i)(10) of this AD.
    (1) Airbus Service Bulletin A320-22-1375, dated January 15, 2014 
(FAC 621 hard B).
    (2) Airbus Service Bulletin A320-22-1427, Revision 05, including 
Appendix 01, dated November 24, 2014 (FAC 622 hard B).
    (3) Airbus Service Bulletin A320-22-1447, Revision 03, dated 
April 21, 2015 (FAC CAA02 hard C).
    (4) Airbus Service Bulletin A320-22-1454, dated February 12, 
2014 (FAC CAA02).
    (5) Airbus Service Bulletin A320-22-1461, Revision 07, including 
Appendix 01, dated March 23, 2015 (FAC 623 hard B).
    (6) Airbus Service Bulletin A320-22-1502, dated November 14, 
2014 (FAC CAA02).
    (7) Airbus Service Bulletin A320-22-1539, Revision 01, dated 
February 24, 2016 (FAC CAA03).
    (8) Airbus Service Bulletin A320-22-1553, dated March 21, 2016 
(FAC B624).
    (9) Airbus Service Bulletin A320-22-1554, dated April 19, 2016 
(FAC CAA03).
    (10) Airbus Service Bulletin A320-31-1414, Revision 03, dated 
September 15, 2014 (FWC H2-F7).

(j) Retained Exclusion From Actions Required by Paragraphs (g) and (h) 
of This AD, With No Changes

    This paragraph restates the requirements of paragraph (j) of AD 
2015-23-13, with no changes. An airplane on which Airbus 
Modification 154473 has been embodied in production is excluded from 
the requirements of paragraphs (g) and (h) of this AD, provided that 
within 30 days after December 29, 2015 (the effective date of AD 
2015-23-13), an inspection of the part numbers of the FWC and the 
FAC installed on the airplane is done to determine that no FWC 
having a part number listed in paragraph (h)(1) of this AD, and no 
FAC having a part number listed in paragraph (h)(2) of this AD, has 
been installed on that airplane since date of manufacture. A review 
of airplane maintenance records is acceptable in lieu of this 
inspection if the part numbers of the FWC and FAC can be 
conclusively determined from that review. If any FWC or FAC having a 
part number identified in paragraph (h)(1) or (h)(2) of this AD, as 
applicable, is installed on a post Airbus Modification 154473 
airplane: Within 30 days after December 29, 2015, do the replacement 
required by paragraph (h) of this AD.

(k) Retained Parts Installation Prohibitions, With New Requirements

    This paragraph restates the parts installation prohibitions 
specified in paragraph (k) of AD 2015-23-13, with new requirements.
    (1) After modification of an airplane as required by paragraphs 
(g), (h), or (j) of this AD: Do not install on that airplane any FWC 
having a part number listed in paragraph (h)(1) of this AD or any 
FAC having a part number listed in paragraph (h)(2) of this AD.
    (2) For an airplane that does not have a FWC having a part 
number listed in paragraph (h)(1) of this AD and does not have a FAC 
having a part number listed in paragraph (h)(2) of this AD: As of 
the effective date of this AD, do not install a FWC having a part 
number listed in paragraph (h)(1) of this AD or a FAC having a part 
number listed in paragraph (h)(2) of this AD.

(l) Retained Later Approved Parts, With a Different Effective Date

    This paragraph restates the requirements of paragraph (l) of AD 
2015-23-13, with a different effective date. Installation of a 
version (part number) of the FWC or FAC approved after March 5, 2015 
(the effective date of European Aviation Safety Agency (EASA) AD 
2014-0217R1), is an approved method of compliance with the 
requirements of paragraph (h) or (j) of this AD, provided the 
requirements specified in paragraphs (l)(1) and (l)(2) of this AD 
are met.
    (1) The version (part number) must be approved by the Manager, 
International Branch, ANM-116, Transport Airplane Directorate, FAA; 
or EASA; or Airbus's EASA Design Organization Approval (DOA).
    (2) The installation must be accomplished using a method 
approved by the Manager, International Branch, ANM-116, Transport 
Airplane Directorate, FAA; or EASA; or Airbus's EASA DOA.

(m) Credit for Previous Actions

    (1) This paragraph restates the credit provided by paragraph 
(m)(1) of AD 2015-23-13. This paragraph provides credit for actions 
required by paragraph (g) of this AD, if those actions were 
performed before December 29, 2015 (the effective date of AD 2015-
23-13) using the service information specified in paragraphs 
(m)(1)(i) or (m)(1)(ii) of this AD.
    (i) Airbus Service Bulletin A320-22-1480, dated July 9, 2014.
    (ii) Airbus Service Bulletin A320-22-1480, Revision 01, dated 
February 6, 2015.
    (2) This paragraph restates the credit provided by paragraph 
(m)(2) of AD 2015-23-13. This paragraph provides credit for actions 
required by paragraph (i) of this AD, if those actions were 
performed before December 29, 2015 (the effective date of AD 2015-
23-13) using the applicable Airbus service information identified in 
paragraphs (m)(2)(i) through (m)(2)(xviii) of this AD.
    (i) Airbus Service Bulletin A320-22-1427, dated January 25, 
2013.
    (ii) Airbus Service Bulletin A320-22-1427, Revision 01, dated 
July 30, 2013.
    (iii) Airbus Service Bulletin A320-22-1427, Revision 02, dated 
October 14, 2013.
    (iv) Airbus Service Bulletin A320-22-1427, Revision 03, dated 
November 8, 2013.
    (v) Airbus Service Bulletin A320-22-1427, Revision 04, dated 
February 11, 2014.
    (vi) Airbus Service Bulletin A320-22-1447, dated October 18, 
2013.
    (vii) Airbus Service Bulletin A320-22-1447, Revision 01, dated 
September 18, 2014.
    (viii) Airbus Service Bulletin A320-22-1447, Revision 02, dated 
December 2, 2014.
    (ix) Airbus Service Bulletin A320-22-1461, dated October 31, 
2013.
    (x) Airbus Service Bulletin A320-22-1461, Revision 01, dated 
February 25, 2014.
    (xi) Airbus Service Bulletin A320-22-1461, Revision 02, dated 
April 30, 2014.
    (xii) Airbus Service Bulletin A320-22-1461, Revision 03, dated 
July 17, 2014.
    (xiii) Airbus Service Bulletin A320-22-1461, Revision 04, dated 
September 15, 2014.
    (xiv) Airbus Service Bulletin A320-22-1461, Revision 05, dated 
November 13, 2014.
    (xv) Airbus Service Bulletin A320-22-1461, Revision 06, dated 
January 21, 2015.
    (xvi) Airbus Service Bulletin A320-31-1414, dated December 19, 
2012.
    (xvii) Airbus Service Bulletin A320-31-1414, Revision 01, dated 
March 21, 2013.
    (xviii) Airbus Service Bulletin A320-31-1414, Revision 02, dated 
July 30, 2013.
    (3) This paragraph provides credit for actions required by 
paragraph (i) of this AD, if those actions were performed before the 
effective date of this AD using Airbus Service Bulletin A320-22-
1539, dated December 28, 2015.

(n) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
has the authority to approve AMOCs for this AD, if requested using 
the procedures found in 14 CFR 39.19. In accordance with 14 CFR 
39.19, send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the International Branch, send it to the attention of 
the person identified in paragraph (o)(2) of this AD. Information 
may be emailed to: [email protected].
    (i) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.
    (ii) AMOCs approved previously for AD 2015-23-13, are approved 
as AMOCs for the corresponding provisions of this AD.
    (2) Contacting the Manufacturer: As of the effective date of 
this AD, for any requirement in this AD to obtain corrective actions 
from a manufacturer, the action must be accomplished using a method 
approved by the Manager, International Branch, ANM-116, Transport 
Airplane Directorate, FAA; or the EASA; or Airbus's EASA DOA. If 
approved by the DOA, the approval must include the DOA-authorized 
signature.
    (3) Required for Compliance (RC): If any service information 
contains procedures or tests that are identified as RC, those 
procedures and tests must be done to comply with this AD; any 
procedures or tests that are not identified as RC are recommended. 
Those procedures and tests that are not identified as RC may be 
deviated from using accepted methods in accordance with the 
operator's

[[Page 29368]]

maintenance or inspection program without obtaining approval of an 
AMOC, provided the procedures and tests identified as RC can be done 
and the airplane can be put back in an airworthy condition. Any 
substitutions or changes to procedures or tests identified as RC 
require approval of an AMOC.

(o) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information 
(MCAI) EASA Airworthiness Directive 2016-0132, dated July 5, 2016; 
corrected July 20, 2016; for related information. This MCAI may be 
found in the AD docket on the Internet at http://www.regulations.gov 
by searching for and locating Docket No. FAA-2016-9573.
    (2) For more information about this AD, contact Sanjay Ralhan, 
Aerospace Engineer, International Branch, ANM-116, Transport 
Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, WA 98057-
3356; telephone 425-227-1405; fax 425-227-1149.
    (3) Service information identified in this AD that is not 
incorporated by reference is available at the addresses specified in 
paragraphs (p)(5) and (p)(6) of this AD.

(p) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (3) The following service information was approved for IBR on 
August 3, 2017.
    (i) Airbus Service Bulletin A320-22-1480, Revision 03, dated 
October 13, 2015.
    (ii) Airbus Service Bulletin A320-22-1539, Revision 01, dated 
February 24, 2016.
    (iii) Airbus Service Bulletin A320-22-1553, dated March 21, 
2016.
    (iv) Airbus Service Bulletin A320-22-1554, dated April 19, 2016.
    (4) The following service information was approved for IBR on 
December 29, 2015 (80 FR 73099, November 24, 2015).
    (i) Airbus Service Bulletin A320-22-1375, dated January 15, 
2014.
    (ii) Airbus Service Bulletin A320-22-1427, Revision 05, 
including Appendix 01, dated November 24, 2014.
    (iii) Airbus Service Bulletin A320-22-1447, Revision 03, dated 
April 21, 2015.
    (iv) Airbus Service Bulletin A320-22-1454, dated February 12, 
2014.
    (v) Airbus Service Bulletin A320-22-1461, Revision 07, including 
Appendix 01, dated March 23, 2015.
    (vi) Airbus Service Bulletin A320-22-1480, Revision 02, dated 
March 30, 2015.
    (vii) Airbus Service Bulletin A320-22-1502, dated November 14, 
2014.
    (viii) Airbus Service Bulletin A320-31-1414, Revision 03, dated 
September 15, 2014.
    (5) For service information identified in this AD, contact 
Airbus, Airworthiness Office--EIAS, 1 Rond Point Maurice Bellonte, 
31707 Blagnac Cedex, France; telephone +33 5 61 93 36 96; fax +33 5 
61 93 44 51; email [email protected]; Internet http://www.airbus.com.
    (6) You may view this service information at the FAA, Transport 
Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For 
information on the availability of this material at the FAA, call 
425-227-1221.
    (7) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued in Renton, Washington, on June 16, 2017.
Michael Kaszycki,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2017-13407 Filed 6-28-17; 8:45 am]
BILLING CODE 4910-13-P

The complete text was extracted from the official GovInfo HTML edition for this publication. Acquired 2026-10-09T02:20:37.200974+00:00. Text extraction preserves the recorded source wording; it does not determine current requirements.

Open the captured official edition

Source SHA-256

c7a64aad337d0fca8758f6201d213d052159ee04db165f74529794c9acebc664

Text SHA-256

8f3fb7bbc8c1c1b1d3405597a48f4eda642766b34f431df78c25dc13282e6b57