Airworthiness Directives; Daher Aircraft Design, LLC (Type Certificate Previously Held by Quest Aircraft Design, LLC), Airplanes

[Federal Register Volume 85, Number 134 (Monday, July 13, 2020)]
[Rules and Regulations]
[Pages 41906-41910]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2020-14886]


=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2018-0180; Project Identifier 2017-CE-043-AD; Amendment 
39-21146; AD 2020-13-01]
RIN 2120-AA64


Airworthiness Directives; Daher Aircraft Design, LLC (Type 
Certificate Previously Held by Quest Aircraft Design, LLC), Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: The FAA is adopting a new airworthiness directive (AD) for all 
Daher Aircraft Design, LLC (type certificate previously held by Quest 
Aircraft Design, LLC), Model KODIAK 100 airplanes. This AD was prompted 
by reports of cracks found in certain nose landing gear (NLG) forks. 
This AD requires a one-time inspection to determine if an affected NLG 
fork is installed, repetitive inspections of the affected NLG fork for 
cracks, repetitive inspections of the shimmy damper bracket for 
looseness, and of the shimmy damper system for damaged components if an 
affected NLG fork is installed, and rework/replacement of parts as 
necessary. The FAA is issuing this AD to address the unsafe condition 
on these products.

DATES: This AD is effective August 17, 2020.
    The Director of the Federal Register approved the incorporation by 
reference of certain publications listed in this AD as of August 17, 
2020.

ADDRESSES: For service information identified in this final rule, 
contact Kodiak Aircraft Company, Inc., 1200 Turbine Drive, Sandpoint, 
Idaho 83864; phone: (208) 263-1111 or 1 (866) 263-1112; email: 
[email protected]; internet: http://Kodiak.aero/support. You may 
view this service information at the FAA, Airworthiness Products 
Section, Operational Safety Branch, 901 Locust, Kansas City, Missouri 
64106. For information on the availability of this material at the FAA, 
call 816-329-4148. It is also available on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2018-
0180.

Examining the AD Docket

    You may examine the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2018-
0180; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this final rule, the regulatory evaluation, any comments received, and 
other information. The address for Docket Operations is U.S. Department 
of Transportation, Docket Operations, M-30, West Building Ground Floor, 
Room W12-140, 1200 New Jersey Avenue SE, Washington, DC 20590.

FOR FURTHER INFORMATION CONTACT: Wade Sullivan, Aerospace Engineer, 
Airframe Section, FAA, Seattle ACO Branch, 2200 South 216th St., Des 
Moines, WA 98198; phone and fax: 206-231-3530; email: 
[email protected].

SUPPLEMENTARY INFORMATION:

Discussion

    The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 
CFR part 39 by adding an AD that would apply to all Quest Aircraft 
Design, LLC (type certificate now held by Daher Aircraft Design, LLC), 
Model KODIAK 100 airplanes. The NPRM published in the Federal Register 
on March 8, 2018 (83 FR 9820). The NPRM was prompted by reports of 
cracks on the NLG fork on Model KODIAK 100 airplanes. The NPRM proposed 
to require a one-time inspection to determine if an affected NLG fork 
is installed, repetitive inspections of the affected NLG fork for 
cracks, repetitive inspections of the shimmy damper bracket for 
looseness if an affected NLG fork is installed, and rework/replacement 
of parts as necessary. The FAA is issuing this AD to prevent separation 
of the NLG fork and consequent reduced control on landing. If the NLG 
fork separates on an unimproved surface, the risk of the NLG digging in 
and the airplane overturning on the ground increases.
    Since the FAA issued the NPRM, the type certificate holder for the 
Model KODIAK 100 airplane changed from Quest Aircraft Design, LLC 
(Quest), to Daher Aircraft Design, LLC. This final rule reflects that 
change and updates the contact information to obtain service 
documentation.

Comments

    The FAA gave the public the opportunity to participate in 
developing this final rule. The following presents the comments 
received on the NPRM and the FAA's response to each comment.

Request To Revise Proposed AD To Lessen Economic Impact

    Quest requested numerous changes to paragraphs (h), (i), and (j) of 
the proposed AD. In support, Quest stated that these changes would 
address all sources of shimmy and lessen the economic impact to 
operators in international locations where nondestructive testing (NDT) 
inspection methods are less accessible.
    First, Quest requested that the FAA change paragraphs (h)(1) and 
(i)(1) of the proposed AD to require the initial inspections only if 
there is shimmy. Quest stated that its analysis and review of the NLG 
fork determined that extended shimmy with the existing design (type A 
NLG fork) could result in fatigue cracks at the locations reported.
    The FAA disagrees with this request because there is no regulatory 
requirement for all pilots to report a nosewheel shimmy event. If the 
initial inspections were conditional on reported shimmy events, the 
unsafe condition would go unaddressed each time a pilot forgot or 
neglected to report an event.
    Quest also requested that the FAA revise the service information 
that would be required throughout the proposed AD to allow later 
revisions.
    The FAA disagrees with this request. Requiring the use of a service 
document that does not yet exist at the time an AD is published 
violates 1 CFR 51.1(f), regarding approval by the Director of the 
Federal Register of a publication incorporated by reference. In order 
for operators to use later revisions of a referenced document (issued 
after the publication of the AD), either the AD must be revised to 
reference the specific later revisions, or operators must request 
approval to use a later revision as an alternative method of compliance 
(AMOC) using the procedures in paragraph (l) of this AD.

[[Page 41907]]

    Quest requested that the FAA revise paragraph (h)(2) of the 
proposed AD to remove the identification of the replacement part so 
that replacement of a cracked NLG fork is not limited to NLG fork P/N 
100-410-7013 (type B).
    The FAA disagrees. The type B NLG fork, P/N 100-410-7013, is the 
only replacement option that has been shown to address the unsafe 
condition. The FAA disagrees with relying solely on the repetitive 
inspections without requiring replacement with the type B NLG fork if a 
crack is found. If a different option provides an acceptable level of 
safety, an operator may request an AMOC using the procedures in 
paragraph (l) of this AD.
    Quest requested that the FAA revise paragraph (i)(1) of the 
proposed AD to change the requirement to inspect the shimmy damper 
bracket for looseness using revision 21 of the maintenance manual to a 
requirement to perform the nosewheel shimmy system troubleshooting 
procedure in revision 24 (or later) of the maintenance manual. In 
support of this request, Quest stated that shimmy can result from a 
wide range of factors, and thus a less focused procedure is more 
appropriate.
    The FAA disagrees with this request. The FAA has determined that 
the procedures to inspect the shimmy damper bracket and replace damaged 
components adequately address the unsafe condition. Performing the 
entire nosewheel shimmy system troubleshooting procedure in Revision 24 
goes beyond what is required and is not necessary to address the unsafe 
condition.
    Quest further requested that the FAA revise paragraph (j) of the 
proposed AD to require replacement of the NLG fork using the procedures 
in the maintenance manual, instead of the procedures in Quest Field 
Service Instruction FSI-147.
    The FAA partially agrees. Replacing an NLG fork with a type B NLG 
fork may be accomplished using the Quest maintenance manual or other 
standard maintenance practices. The FAA has changed paragraph (j) of 
this AD accordingly.

Request To Extend the Repetitive Inspection Intervals

    Quest, New Tribes Mission (Papua New Guinea) Ltd (New Tribes 
Mission), and SIL Aviation requested that the FAA extend the repetitive 
inspection intervals for the NDT inspection of the NLG fork. In the 
NPRM, the FAA proposed a 100-hour TIS interval; the commenters 
requested an interval ranging from 200 to 1,000 hours TIS. According to 
New Tribes Mission, extending the repetitive interval would align with 
other scheduled Kodiak inspection items and still provide a measure of 
assurance that no cracks are forming, while reducing labor time and 
costs and increasing aircraft availability for operators. Quest stated 
that the 30-second duration of a severe shimmy occurrence used in its 
original analysis was extraordinarily long, and suggested that half 
that duration would still provide a reasonable and conservative number 
for analysis and allow increasing the repetitive inspection interval to 
200 hours TIS.
    The FAA agrees with the analysis supporting an increase in the 
repetitive inspection intervals to 200 hours TIS and has revised 
paragraphs (h)(1) and (i)(1) of this AD accordingly. The FAA has 
determined there is insufficient data to support increasing the 
repetitive inspection intervals beyond 200 hours TIS. The FAA will 
consider a further extension of this repetitive interval, via further 
rulemaking or approval of an AMOC, if analysis of the nosewheel shimmy 
and the effect of the NLG gravel deflectors shows that safety would be 
ensured by a longer interval.

Request To Extend Repetitive Interval Based on Shimmy Documentation

    Quest requested that the FAA allow a longer repetitive inspection 
interval of 800 hours TIS for operators that implement a shimmy-
occurrence documentation procedure and where no severe shimmy (longer 
than 3 seconds per landing) occurs. The commenter suggested that it was 
important for international operators to include this option in the AD 
instead of through an AMOC because of the various international 
regulations and associated complexities in obtaining approvals.
    The FAA disagrees with this request. Although the engineering 
analysis provided by Quest suggests that cracks are more likely to 
develop in airplanes that experience nosewheel shimmy, there is no 
regulatory requirement for all pilots to report or record a shimmy 
event. Even if an operator were to adopt and implement a procedure, 
there is no reliable way to determine if an airplane has experienced a 
previous shimmy event. A new owner of an airplane would have no way of 
determining if the airplane had experienced a shimmy event with the 
previous owner based on a review of the maintenance records. The FAA 
has not changed this AD based on this comment.

Request To Limit Applicability to Airplanes With NLG Gravel Deflector

    New Tribes Mission and SIL Aviation requested that the FAA limit 
the applicability of the proposed AD to airplanes with a supplemental 
type certificate (STC) for an NLG gravel deflector installed. The 
commenters stated that the four instances of cracking on the NLG fork 
were limited to airplanes of the same operator, operated in the same 
location, with an STC for an NLG gravel deflector installed. New Tribes 
Mission noted that the extra weight of the gravel deflector could 
exacerbate the effects of the shimmy. Both commenters stated that other 
operators in similar locations and conditions, with airplanes that had 
accumulated more hours TIS and landings but without the gravel 
deflector installed, have not reported any signs of cracking on 
airplanes.
    The FAA does not agree with this request. Although Quest's analysis 
suggests that nosewheel shimmy contributes to the cracking, there is 
insufficient data to make that conclusion specifically for airplanes 
with the gravel deflector installed. Should Quest complete a shimmy 
analysis of the effect of the NLG gravel deflectors, the FAA will 
determine whether to take further rulemaking action.
    The FAA has not changed this AD based on this comment.

Request To Allow Credit for Inspections Already Completed

    Quest requested that the FAA provide relief from the initial 
requirement to perform an NDT inspection within 25 hours if an operator 
has previously complied with the inspection. Quest stated that such 
operators should not be required to perform another ``initial'' 
inspection.
    Paragraph (f) of this AD requires compliance unless already done. 
Thus, the AD already allows operators to take credit for the initial 
NDT inspection if it is done before the effective date of the AD. 
Operators must then repeat the inspection at intervals not to exceed 
200 hours TIS. No changes to this AD are necessary based on this 
comment.

Comments Regarding the Type of Inspection

    SIL Aviation and New Tribes Mission stated that the NDT inspection 
methods required by the AD are not readily available and/or are cost 
prohibitive. SIL Aviation noted that the type of inspection would be 
very costly to its operation. The FAA infers that these commenters 
would like the AD to allow the inspection using a different method.
    The FAA acknowledges the commenters' concerns about the costs 
associated with this AD. However, the FAA has determined that the 
required

[[Page 41908]]

actions in this AD are necessary to address the unsafe condition. The 
FAA considered several possible NDT methods and determined that the 
inspection options (fluorescent penetrant, dye penetrant, or eddy 
current inspection) for the inspection required by this AD are the most 
cost effective and simple to perform in the field while still providing 
an adequate level of safety. The dye penetrant kits are available from 
several sources. Under the provisions of paragraph (l) of this AD, 
operators may request approval of an AMOC for a different inspection 
method if that method provides the same or higher level of crack 
detection.

Other Changes to the Proposed AD

    In the NPRM, the FAA proposed that paragraph (h)(2) require 
replacing a cracked NLG fork by following section 5. Instructions in 
Quest Aircraft Field Service Instruction FSI-147, Revision 00 (not 
dated), and paragraph (i)(3) require replacing damaged components by 
following pages 32_110 and 32_111, section 3252, Shimmy Damper, in 
Chapter 32, Landing Gear, of Quest Aircraft Company Kodiak 100 
Maintenance Manual, Revision No. 21, dated February 15, 2017. The FAA 
has revised paragraphs (h)(2) and (i)(3) in this AD to remove the 
incorporation by reference of the specified service information to 
allow the actions to be done using standard maintenance practices.
    The FAA has also clarified the proposed requirements in paragraph 
(i). Paragraph (i)(1) of the proposed AD specified inspecting the 
shimmy damper bracket for looseness by following pages 32_110 and 
32_111, section 3252, Shimmy Damper, found in Chapter 32, Landing Gear, 
of Quest Aircraft Company Kodiak 100 Maintenance Manual, Revision No. 
21, dated February 15, 2017. Section 3252 contains a broader inspection 
procedure of the shimmy damper system and not only an inspection of the 
bracket for looseness. Paragraph (i)(3) of the proposed AD then 
specified corrective action for damaged components in the shimmy damper 
system as a result of the inspection in paragraph (i)(1). The FAA has 
revised paragraph (i)(1) in this AD to clarify that the entire 
inspection of the shimmy damper system is required.

Conclusion

    The FAA reviewed the relevant data, considered the comments 
received, and determined that air safety and the public interest 
require adopting this final rule with the changes described previously 
and minor editorial changes. The FAA has determined that these changes:
    <bullet> [Agr]re consistent with the proposal in the NPRM for 
addressing the unsafe condition; and
    <bullet> Do not add any burden upon the public than was already 
proposed in the NPRM.
    The FAA also determined that these changes will not increase the 
economic burden on any operator or increase the scope of this final 
rule.

Related Service Information Under 1 CFR Part 51

    The FAA reviewed Quest Aircraft Field Service Instruction FSI-147, 
Revision 00, Release Date January 29, 2018, which provides instructions 
for inspection and, if necessary, replacement of the NLG fork. The FAA 
reviewed pages 32_110 and 32_111, section 3252, Shimmy Damper, in 
Chapter 32, Landing Gear, of Quest Aircraft Company Kodiak 100 
Maintenance Manual, Revision No. 21, dated February 15, 2017, which 
contains procedures for inspecting the shimmy damper system. The FAA 
also reviewed Quest Aircraft Field Service Instruction FSI-146, 
Revision 00, Release Date April 18, 2017, which provides instructions 
for modifying the shimmy damper attach bracket. This service 
information is reasonably available because the interested parties have 
access to it through their normal course of business or by the means 
identified in the ADDRESSES section.

Costs of Compliance

    The FAA estimates that this AD affects 116 airplanes of U.S. 
registry. The FAA estimates the following costs to comply with this AD:

                                                 Estimated Costs
----------------------------------------------------------------------------------------------------------------
                                                                                     Cost per      Cost on U.S.
             Action                   Labor cost              Parts cost              product        operators
----------------------------------------------------------------------------------------------------------------
Determine if type A or type B     1 work-hour x $85   Not applicable............             $85          $9,860
 NLG fork is installed.            per hour = $85.
----------------------------------------------------------------------------------------------------------------

    The FAA estimates the following costs to do any necessary 
additional inspections, replacements, and modifications that would be 
required based on the results of the NLG fork type determination. The 
FAA has no way of determining the number of airplanes that might need 
these inspections, replacements, and modifications:

                                               On-Condition Costs
----------------------------------------------------------------------------------------------------------------
            Action                  Labor cost             Parts cost                  Cost per product
----------------------------------------------------------------------------------------------------------------
Inspection of the NLG fork for  4 work-hours x     Not applicable...........  $340 per inspection cycle.
 cracks.                         $85 per hour =
                                 $340.
Replacement of the NLG fork...  4 work-hours x     $7,002.36................  $7,342.36.
                                 $85 per hour =
                                 $340.
Inspection of the shimmy        1 work-hour x $85  Not applicable...........  $85 per inspection cycle.
 damper system including the     per hour = $85.
 bracket.
Rework of the shimmy damper     4 work-hours x     $127.33..................  $467.33.
 bracket.                        $85 per hour =
                                 $340.
----------------------------------------------------------------------------------------------------------------

    The FAA has received no definitive data that would enable the 
agency to provide cost estimates for replacing damaged components 
specified in this AD.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.

[[Page 41909]]

    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Will not affect intrastate aviation in Alaska, and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13   [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

2020-13-01 Quest Aircraft Design, LLC: Amendment 39-21146; Docket 
No. FAA-2018-0180; Project Identifier 2017-CE-043-AD.

(a) Effective Date

    This airworthiness directive (AD) is effective August 17, 2020.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Daher Aircraft Design, LLC (type certificate 
previously held by Quest Aircraft Design, LLC), Model KODIAK 100 
airplanes, all serial numbers, certificated in any category.

(d) Subject

    Joint Aircraft System Component (JASC)/Air Transport Association 
(ATA) of America Code 32, Landing Gear.

(e) Unsafe Condition

    This AD was prompted by reports from the manufacturer of fatigue 
cracks on the nose landing gear (NLG) fork. The FAA is issuing this 
AD to detect and prevent fatigue cracking of the NLG fork. The 
unsafe condition, if not corrected, could result in separation of 
the NLG fork with consequent reduced control on landing. If the NLG 
fork separates on an unimproved surface, the risk of the NLG digging 
in and the airplane overturning on the ground increases.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Inspection for Type of NLG Fork

    Within 25 hours time-in-service (TIS) after August 17, 2020 (the 
effective date of this AD), inspect the airplane to determine if an 
NLG fork part number (P/N) 100-410-7001 (type A) or an NLG fork P/N 
100-410-7013 (type B) is installed. If you determine that an NLG 
fork P/N 100-410-7013 (type B) is installed during the inspection, 
no further action is required by this AD. If a review of the 
maintenance records can identify the P/N NLG fork that is installed, 
you may use a maintenance records review in lieu of inspecting the 
airplane to determine if an NLG fork P/N 100-410-7001 (type A) or an 
NLG fork P/N 100-410-7013 (type B) is installed.

(h) Inspection of the NLG Fork for Cracks

    (1) If you determine that an NLG fork P/N 100-410-7001 (type A) 
is installed during the inspection required by paragraph (g) of this 
AD, within 25 hours TIS after August 17, 2020 (the effective date of 
this AD) and thereafter at intervals not to exceed 200 hours TIS, do 
a fluorescent penetrant, dye penetrant, or open-hole eddy current 
inspection of the NLG fork for cracks by following section 5. 
Instructions in Quest Aircraft Field Service Instruction FSI-147, 
Revision 00, Release Date January 29, 2018.
    (2) If you find any cracks of the NLG fork during any inspection 
required by paragraph (h)(1) of this AD, before further flight, 
replace the NLG fork with an NLG fork P/N 100-410-7013 (type B). 
Replacement of the NLG fork with an NLG fork P/N 100-410-7013 (type 
B) terminates the repetitive inspections required by paragraphs 
(h)(1) and (i)(1) of this AD.

(i) Inspection of the Shimmy Damper Bracket

    (1) If you have not replaced an NLG fork P/N 100-410-7001 (type 
A) per the initial inspection and replacement requirements in 
paragraph (h) of this AD, then within 25 hours TIS after August 17, 
2020 (the effective date of this AD) and thereafter at intervals not 
to exceed 200 hours TIS (until the NLG fork is replaced with a P/N 
100-410-7013 (type B) fork), inspect the shimmy damper bracket for 
looseness, and inspect the shimmy damper system for damaged (loose, 
leaking, corroded, or worn) components, by following pages 32_110 
and 32_111, section 3252, Shimmy Damper, found in Chapter 32, 
Landing Gear, of Quest Aircraft Company Kodiak 100 Maintenance 
Manual, Revision No. 21, dated February 15, 2017.
    (2) If a loose shimmy damper bracket is found during any 
inspection required by paragraph (i)(1) of this AD, rework the 
shimmy damper bracket with interference-fit bolts by following Quest 
Aircraft Field Service Instruction FSI-146, Revision 00, Release 
Date April 18, 2017. Reworking the shimmy damper bracket with the 
interference-fit bolts terminates the repetitive inspections 
required by paragraph (i)(1) of this AD.
    (3) If any other damaged components are found in the shimmy 
damper system during any inspection required by paragraph (i)(1) of 
this AD, before further flight, replace the damaged components.

(j) Optional Terminating Action

    In lieu of the NLG fork and shimmy damper bracket inspections 
required by paragraphs (h)(1) and (i)(1) of this AD, you may replace 
the NLG fork P/N 100-410-7001 (type A) with an NLG fork P/N 100-410-
7013 (type B). This replacement terminates the inspection 
requirements of this AD, and no further actions are required.

(k) Restriction of NLG Fork P/N 100-410-7001 (Type A) Installation

    Once an NLG fork P/N 100-410-7013 (type B) is installed on an 
airplane, do not install an NLG fork P/N 100-410-7001 (type A). If 
an NLG fork P/N 100-410-7013 (type B) is removed from the airplane 
for any reason (for example, to install floats), you must reinstall 
an NLG fork P/N 100-410-7013 (type B) when operating with wheels.

(l) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Seattle ACO Branch, FAA, has the authority to 
approve AMOCs for this AD, if requested using the procedures found 
in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request 
to your principal inspector or local Flight Standards District 
Office, as appropriate. If sending information directly to the 
manager of the certification office, send it to the attention of the 
person identified in paragraph (m) of this AD. Information may also 
be emailed to: [email protected].
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.

(m) Related Information

    For more information about this AD, contact Wade Sullivan, 
Aerospace Engineer, Aerospace Engineer, Airframe Section, FAA,

[[Page 41910]]

Seattle ACO Branch, 2200 South 216th St., Des Moines, WA 98198; 
phone and fax: 206-231-3530; email: [email protected].

(n) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference of the service information listed in this 
paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless the AD specifies otherwise.
    (i) Pages 32_110 and 32_111, section 3252, Shimmy Damper, 
Chapter 32, Landing Gear, of Quest Aircraft Company Kodiak 100 
Maintenance Manual, Revision No. 21, dated February 15, 2017.
    (ii) Quest Aircraft Field Service Instruction FSI-146, Revision 
00, Release Date April 18, 2017.

    Note 1 to paragraph (n)(2)(ii) of this AD:  The Release Date is 
a pen-and-ink addition that appears only on the Revision Notice 
transmitted with FSI-146.

    (iii) Quest Aircraft Field Service Instruction FSI-147, Revision 
00, Release Date January 29, 2018.

    Note 2 to paragraph (n)(2)(iii) of this AD:  The Release Date is 
a pen-and-ink addition that appears only on the Revision Notice 
transmitted with FSI-147.

    (3) For service information identified in this AD, contact 
Kodiak Aircraft Company, Inc., 1200 Turbine Drive, Sandpoint, Idaho 
83864; phone: (208) 263-1111 or 1 (866) 263-1112; email: 
[email protected]; internet: http://Kodiak.aero/support.
    (4) You may view this service information at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 901 
Locust, Kansas City, Missouri 64106. For information on the 
availability of this material at the FAA, call (816) 329-4148.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, email [email protected], or go to https://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued on June 9, 2020.
Ross Landes,
Deputy Director for Regulatory Operations, Compliance & Airworthiness 
Division, Aircraft Certification Service.
[FR Doc. 2020-14886 Filed 7-10-20; 8:45 am]
BILLING CODE 4910-13-P

The complete text was extracted from the official GovInfo HTML edition for this publication. Acquired 2026-10-09T01:58:01.897478+00:00. Text extraction preserves the recorded source wording; it does not determine current requirements.

Open the captured official edition

Source SHA-256

c6bd391b4c3e716236e14d87826b6c9ab4e95d9035b77493391fd3454c4483c9

Text SHA-256

6c6101d96fefb44de7762fb981278e9ca83e44f50762c5fa242a7e2f7f99f0d0