Airworthiness Directives; Airbus SAS Airplanes

[Federal Register Volume 86, Number 34 (Tuesday, February 23, 2021)]
[Rules and Regulations]
[Pages 10772-10775]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2021-03568]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2020-0969; Project Identifier MCAI-2020-00853-T; 
Amendment 39-21393; AD 2021-02-10]
RIN 2120-AA64


Airworthiness Directives; Airbus SAS Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

[[Page 10773]]


ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: The FAA is adopting a new airworthiness directive (AD) for all 
Airbus SAS Model A350-941 and -1041 airplanes. This AD was prompted by 
a report that certain retaining rings could cause damage to frame 
forks, brackets and edge frames, and their surface protection; 
subsequent investigation showed that the depth of the frame fork 
spotfacing on structural parts is inadequate to accommodate the 
retaining ring. This AD requires repetitive inspections of certain 
areas of each cargo door for damage and corrective action. This AD also 
provides an optional terminating modification, as specified in a 
European Union Aviation Safety Agency (EASA) AD, which is incorporated 
by reference. The FAA is issuing this AD to address the unsafe 
condition on these products.

DATES: This AD is effective March 30, 2021.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of March 30, 
2021.

ADDRESSES: For material incorporated by reference (IBR) in this AD, 
contact the EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; 
telephone +49 221 8999 000; email [email protected]; internet 
www.easa.europa.eu. You may find this IBR material on the EASA website 
at https://ad.easa.europa.eu. You may view this IBR material at the 
FAA, Airworthiness Products Section, Operational Safety Branch, 2200 
South 216th St., Des Moines, WA. For information on the availability of 
this material at the FAA, call 206-231-3195. It is also available in 
the AD docket on the internet at https://www.regulations.gov by 
searching for and locating Docket No. FAA-2020-0969.

Examining the AD Docket

    You may examine the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2020-
0969; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this final rule, any comments received, and other information. The 
address for Docket Operations is U.S. Department of Transportation, 
Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 
New Jersey Avenue SE, Washington, DC 20590.

FOR FURTHER INFORMATION CONTACT: Kathleen Arrigotti, Aerospace 
Engineer, Large Aircraft Section, International Validation Branch, FAA, 
2200 South 216th St., Des Moines, WA 98198; telephone and fax 206-231-
3218; email [email protected].

SUPPLEMENTARY INFORMATION:

Discussion

    The EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA AD 2020-0144, dated June 29, 2020 (EASA 
AD 2020-0144) (also referred to as the Mandatory Continuing 
Airworthiness Information, or the MCAI), to correct an unsafe condition 
for all Airbus SAS Model A350-941 and -1041 airplanes.
    The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 
CFR part 39 by adding an AD that would apply to all Airbus SAS Model 
A350-941 and -1041 airplanes. The NPRM published in the Federal 
Register on October 26, 2020 (85 FR 67696). The NPRM was prompted by a 
report that certain retaining rings could cause damage to frame forks, 
brackets and edge frames, and their surface protection; subsequent 
investigation showed that the depth of the frame fork spotfacing on 
structural parts is inadequate to accommodate the retaining ring. The 
NPRM proposed to require repetitive inspections of certain areas of 
each cargo door for damage and corrective action. The NPRM also 
proposed to provide an optional terminating modification, as specified 
in an EASA AD.
    The FAA is issuing this AD to address inadequate frame fork 
spotfacing depth for the retaining rings, which could reduce the 
structural integrity of the airplane. See the MCAI for additional 
background information.

Comments

    The FAA gave the public the opportunity to participate in 
developing this final rule. The FAA received no comments on the NPRM or 
on the determination of the cost to the public.

Conclusion

    The FAA reviewed the relevant data and determined that air safety 
and the public interest require adopting this final rule as proposed, 
except for minor editorial changes. The FAA has determined that these 
minor changes:
    <bullet> Are consistent with the intent that was proposed in the 
NPRM for addressing the unsafe condition; and
    <bullet> Do not add any additional burden upon the public than was 
already proposed in the NPRM.

Related Service Information Under 1 CFR Part 51

    EASA AD 2020-0144 describes procedures for repetitive inspections 
of the edge frames, brackets, frame forks, and the access cover on the 
internal side of each cargo door for damage (including cracks and 
corrosion) and corrective actions. Corrective actions include repair or 
rework. EASA AD 2020-0144 also describes procedures for an optional 
modification of each affected cargo door, which terminates the 
repetitive inspections. This material is reasonably available because 
the interested parties have access to it through their normal course of 
business or by the means identified in the ADDRESSES section.

Costs of Compliance

    The FAA estimates that this AD affects 13 airplanes of U.S. 
registry. The FAA estimates the following costs to comply with this AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                    Cost per       Cost on U.S.
                          Labor cost                              Parts cost        product         operators
----------------------------------------------------------------------------------------------------------------
24 work-hours x $85 per hour = $2,040........................              $0           $2,040          $26,520
----------------------------------------------------------------------------------------------------------------


                  Estimated Costs for Optional Actions
------------------------------------------------------------------------
         Labor cost                Parts cost         Cost per product
------------------------------------------------------------------------
9 work-hours x $85 per hour   Up to $8,570........  Up to $9,335.
 = $765.
------------------------------------------------------------------------


[[Page 10774]]

    The FAA has received no definitive data on which to base the cost 
estimates for the on-condition actions specified in this AD.
    According to the manufacturer, some or all of the costs of this AD 
may be covered under warranty, thereby reducing the cost impact on 
affected operators. The FAA does not control warranty coverage for 
affected operators. As a result, the FAA has included all known costs 
in the cost estimate.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Will not affect intrastate aviation in Alaska, and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

2021-02-10 Airbus SAS: Amendment 39-21393; Docket No. FAA-2020-0969; 
Project Identifier MCAI-2020-00853-T.

(a) Effective Date

    This airworthiness directive (AD) is effective March 30, 2021.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to all Airbus SAS Model A350-941 and -1041 
airplanes, certificated in any category.

(d) Subject

    Air Transport Association (ATA) of America Code 52, Doors.

(e) Reason

    This AD was prompted by a report that certain retaining rings 
could cause damage to frame forks, brackets and edge frames, and 
their surface protection; subsequent investigation showed that the 
depth of the frame fork spotfacing on structural parts is inadequate 
to accommodate the retaining ring. The FAA is issuing this AD to 
address inadequate frame fork spotfacing depth for the retaining 
rings, which could reduce the structural integrity of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, European Union Aviation Safety Agency (EASA) AD 
2020-0144, dated June 29, 2020 (EASA AD 2020-0144).

(h) Exceptions to EASA AD 2020-0144

    (1) Where EASA AD 2020-0144 refers to its effective date, this 
AD requires using the effective date of this AD.
    (2) The ``Remarks'' section of EASA AD 2020-0144 does not apply 
to this AD.

(i) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
Large Aircraft Section, International Validation Branch, FAA, has 
the authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or responsible Flight 
Standards Office, as appropriate. If sending information directly to 
the Large Aircraft Section, International Validation Branch, send it 
to the attention of the person identified in paragraph (j) of this 
AD. Information may be emailed to: [email protected]. 
Before using any approved AMOC, notify your appropriate principal 
inspector, or lacking a principal inspector, the manager of the 
responsible Flight Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, Large Aircraft 
Section, International Validation Branch, FAA; or EASA; or Airbus 
SAS's EASA Design Organization Approval (DOA). If approved by the 
DOA, the approval must include the DOA-authorized signature.
    (3) Required for Compliance (RC): Except as required by 
paragraph (i)(2) of this AD, if any service information contains 
procedures or tests that are identified as RC, those procedures and 
tests must be done to comply with this AD; any procedures or tests 
that are not identified as RC are recommended. Those procedures and 
tests that are not identified as RC may be deviated from using 
accepted methods in accordance with the operator's maintenance or 
inspection program without obtaining approval of an AMOC, provided 
the procedures and tests identified as RC can be done and the 
airplane can be put back in an airworthy condition. Any 
substitutions or changes to procedures or tests identified as RC 
require approval of an AMOC.

(j) Related Information

    For more information about this AD, contact Kathleen Arrigotti, 
Aerospace Engineer, Large Aircraft Section, International Validation 
Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone 
and fax 206-231-3218; email [email protected].

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) European Union Aviation Safety Agency (EASA) AD 2020-0144, 
dated June 29, 2020.
    (ii) [Reserved]
    (3) For EASA AD 2020-0144, contact the EASA, Konrad-Adenauer-
Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email 
[email protected]; Internet www.easa.europa.eu. You may find this 
EASA AD on the EASA website at https://ad.easa.europa.eu.
    (4) You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th St., 
Des Moines, WA. For information on the availability of this material 
at the FAA, call 206-231-3195. This material may be found

[[Page 10775]]

in the AD docket on the internet at https://www.regulations.gov by 
searching for and locating Docket No. FAA-2020-0969.
    (5) You may view this material that is incorporated by reference 
at the National Archives and Records Administration (NARA). For 
information on the availability of this material at NARA, email 
[email protected], or go to: https://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued on January 12, 2021.
Lance T. Gant,
Director, Compliance & Airworthiness Division, Aircraft Certification 
Service.
[FR Doc. 2021-03568 Filed 2-22-21; 8:45 am]
BILLING CODE 4910-13-P

The complete text was extracted from the official GovInfo HTML edition for this publication. Acquired 2026-10-09T01:53:52.575953+00:00. Text extraction preserves the recorded source wording; it does not determine current requirements.

Open the captured official edition

Source SHA-256

4a0786f30f1089d80f4362026b705d0d9e1d136483475fbb5906e368f225588e

Text SHA-256

9919cb11d4bae07d08cc54b12dc32494d6ee56eda07f09b0762375f067d0cde3