Airworthiness Directives; Airbus Canada Limited Partnership (Type Certificate Previously Held by C Series Aircraft Limited Partnership (CSALP); Bombardier, Inc.) Airplanes

[Federal Register Volume 87, Number 216 (Wednesday, November 9, 2022)]
[Rules and Regulations]
[Pages 67543-67545]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2022-24311]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2022-0982; Project Identifier MCAI-2021-00787-T; 
Amendment 39-22202; AD 2022-21-03]
RIN 2120-AA64


Airworthiness Directives; Airbus Canada Limited Partnership (Type 
Certificate Previously Held by C Series Aircraft Limited Partnership 
(CSALP); Bombardier, Inc.) Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: The FAA is adopting a new airworthiness directive (AD) for 
certain Airbus Canada Limited Partnership Model BD-500-1A10 and BD-500-
1A11 airplanes. This AD was prompted by reports that the engine feed 
pressure switches were installed with no secondary locking mechanism 
and can become loose and cause a fuel leak. This AD requires initial 
and repetitive inspections at the engine feed pressure switch locations 
and installation of a flange adaptor with lockwire to terminate the 
repetitive inspections, as specified in a Transport Canada Civil 
Aviation (TCCA) AD, which is incorporated by reference. The FAA is 
issuing this AD to address the unsafe condition on these products.

DATES: This AD is effective December 14, 2022.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of December 14, 
2022.

ADDRESSES: 
    AD Docket: You may examine the AD docket at regulations.gov under 
Docket No. FAA-2022-0982; or in person at Docket Operations between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD 
docket contains this final rule, the mandatory continuing airworthiness 
information (MCAI), any comments received, and other information. The 
address for Docket Operations is U.S. Department of Transportation, 
Docket Operations, M-30, West Building, Ground Floor, Room W12-140, 
1200 New Jersey Avenue SE, Washington, DC 20590.
    Material Incorporated by Reference:
    <bullet> For material incorporated by reference in this AD, contact 
TCCA, Transport Canada National Aircraft Certification, 159 Cleopatra 
Drive, Nepean, Ontario K1A 0N5, Canada; telephone 888-663-3639; email 
[email protected]; website tc.canada.ca/en/aviation.
    <bullet> You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th St., Des 
Moines, WA. For information on the availability of this material at the 
FAA, call 206-231-3195. It is also available in the AD docket at 
regulations.gov under Docket No. FAA-2022-0982.

FOR FURTHER INFORMATION CONTACT: Joseph Catanzaro, Aerospace Engineer, 
Airframe and Propulsion Section, FAA, New York ACO Branch, 1600 Stewart 
Avenue, Suite 410, Westbury, NY 11590; telephone 516-228-7366; email [email protected].

SUPPLEMENTARY INFORMATION:

Background

    The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 
CFR part 39 by adding an AD that would apply to certain Airbus Canada 
Limited Partnership Model BD-500-1A10 and BD-500-1A11 airplanes. The 
NPRM published in the Federal Register on July 29, 2022 (87 FR 45712). 
The NPRM was prompted by AD CF-2021-50, dated December 21, 2021, issued 
by TCCA, which is the aviation authority for Canada (referred to after 
this as the MCAI). The MCAI states that certain fuel system pressure 
switches have been installed on the left-hand and right-hand wings 
without a secondary locking feature (lockwire). This condition may 
allow the fuel pressure switches to become loose and allow fuel to leak 
in the affected areas, creating a fire hazard.
    In the NPRM, the FAA proposed to require initial and repetitive 
inspections at the engine feed pressure switch locations and 
installation of a flange adaptor with lockwire to terminate the 
repetitive inspections, as specified in TCCA AD CF-2021-50. The FAA is 
issuing this AD to address the unsafe condition on these products.

[[Page 67544]]

    You may examine the MCAI in the AD docket at regulations.gov under 
Docket No. FAA-2022-0982.

Discussion of Final Airworthiness Directive

Comments

    The FAA received no comments on the NPRM or on the determination of 
the cost to the public.

Conclusion

    This product has been approved by the aviation authority of another 
country and is approved for operation in the United States. Pursuant to 
the FAA's bilateral agreement with this State of Design Authority, it 
has notified the FAA of the unsafe condition described in the MCAI 
referenced above. The FAA reviewed the relevant data and determined 
that air safety requires adopting this AD as proposed. Accordingly, the 
FAA is issuing this AD to address the unsafe condition on this product. 
Except for minor editorial changes, this AD is adopted as proposed in 
the NPRM. None of the changes will increase the economic burden on any 
operator.

Related Service Information Under 1 CFR Part 51

    TCCA AD CF-2021-50 specifies procedures for repetitive general 
visual inspections of the torque identification stripes, torquing of 
the fuel pressure switches, and installation of lockwire at the two 
alternating current (AC) boost pump cartridges; repetitive general 
visual inspections of the torque identification stripes and torquing of 
the fuel pressure switches at the two engine feed pressure switches; 
and installation of a new flange adaptor and lockwire, which terminates 
the repetitive inspections. This material is reasonably available 
because the interested parties have access to it through their normal 
course of business or by the means identified in the ADDRESSES section.

Costs of Compliance

    The FAA estimates that this AD affects 60 airplanes of U.S. 
registry. The FAA estimates the following costs to comply with this AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                                   Cost on U.S.
                Labor cost                    Parts cost              Cost per  product              operators
----------------------------------------------------------------------------------------------------------------
Up to 27 work-hours x $85 per hour =                  $811  Up to $2,295........................        $137,700
 $2,295.
----------------------------------------------------------------------------------------------------------------

    The FAA estimates the following costs to do any necessary on-
condition actions that would be required based on the results of any 
required actions. The FAA has no way of determining the number of 
aircraft that might need these on-condition action:

                 Estimated Costs of On-Condition Actions
------------------------------------------------------------------------
                                                             Cost per
              Labor cost                   Parts cost        product
------------------------------------------------------------------------
14 work-hours x $85 per hour = $1,190.              $0           $1,190
------------------------------------------------------------------------

    The FAA has included all known costs in its cost estimate. 
According to the manufacturer, however, some or all of the costs of 
this AD may be covered under warranty, thereby reducing the cost impact 
on affected operators.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Will not affect intrastate aviation in Alaska, and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13   [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

2022-21-03 Airbus Canada Limited Partnership (Type Certificate 
Previously Held by C Series Aircraft Limited Partnership (CSALP); 
Bombardier, Inc.): Amendment 39-22202; Docket No. FAA-2022-0982; 
Project Identifier MCAI-2021-00787-T.

(a) Effective Date

    This airworthiness directive (AD) is effective December 14, 
2022.

[[Page 67545]]

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Airbus Canada Limited Partnership Model BD-
500-1A10 and BD-500-1A11 airplanes, certificated in any category, as 
identified in Transport Canada Civil Aviation (TCCA) AD CF-2021-50, 
dated December 21, 2021 (TCCA AD CF-2021-50).

(d) Subject

    Air Transport Association (ATA) of America Code 28, Fuel.

(e) Unsafe Condition

    This AD was prompted by reports that the engine feed pressure 
switches were installed with no secondary locking mechanism and can 
become loose and cause a fuel leak. The FAA is issuing this AD to 
address the absence of a secondary locking feature (lockwire) on the 
fuel pressure switches, which may allow them to become loose and 
allow fuel to leak in the affected areas, creating a fire hazard.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, TCCA AD CF-2021-50.

(h) Exception to TCCA AD CF-2021-50

    (1) Where TCCA AD CF-2021-50 refers to hours air time, this AD 
requires using flight hours.
    (2) Where TCCA AD CF-2021-50 refers to its effective date, or 14 
July 2021, the effective date of TCCA AD CF-2021-21, this AD 
requires using the effective date of this AD.

(i) Additional AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, New 
York ACO Branch, FAA, has the authority to approve AMOCs for this 
AD, if requested using the procedures found in 14 CFR 39.19. In 
accordance with 14 CFR 39.19, send your request to your principal 
inspector or responsible Flight Standards Office, as appropriate. If 
sending information directly to the manager of the certification 
office, send it to ATTN: Program Manager, Continuing Operational 
Safety, FAA, New York ACO Branch, 1600 Stewart Avenue, Suite 410, 
Westbury, NY 11590; telephone 516-228-7300. Before using any 
approved AMOC, notify your appropriate principal inspector, or 
lacking a principal inspector, the manager of the responsible Flight 
Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, New York ACO 
Branch, FAA; or TCCA; or Airbus Canada Limited Partnership's TCCA 
Design Approval Organization (DAO). If approved by the DAO, the 
approval must include the DAO-authorized signature.

(j) Additional Information

    For more information about this AD, contact Joseph Catanzaro, 
Aerospace Engineer, Airframe and Propulsion Section, FAA, New York 
ACO Branch, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; 
telephone 516-228-7366; email [email protected].

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference of the service information listed in this 
paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) Transport Canada Civil Aviation (TCCA) AD CF-2021-50, dated 
December 21, 2021.
    (ii) [Reserved]
    (3) For TCCA AD CF-2021-50, contact TCCA, Transport Canada 
National Aircraft Certification, 159 Cleopatra Drive, Nepean, 
Ontario K1A 0N5, Canada; telephone 888-663-3639; email [email protected]; website tc.canada.ca/en/aviation.
    (4) You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th St., 
Des Moines, WA. For information on the availability of this material 
at the FAA, call 206-231-3195.
    (5) You may view this material that is incorporated by reference 
at the National Archives and Records Administration (NARA). For 
information on the availability of this material at NARA, email 
[email protected], or go to: www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued on September 28, 2022.
Christina Underwood,
Acting Director, Compliance & Airworthiness Division, Aircraft 
Certification Service.
[FR Doc. 2022-24311 Filed 11-8-22; 8:45 am]
BILLING CODE 4910-13-P

The complete text was extracted from the official GovInfo HTML edition for this publication. Acquired 2026-10-09T01:39:22.863438+00:00. Text extraction preserves the recorded source wording; it does not determine current requirements.

Open the captured official edition

Source SHA-256

66da5ab247deb216d8d3c1d8e86635b718f011457b1362bcf381ba168b88413e

Text SHA-256

5d01f1fe7f4c3645a364ccefcadf29b53b9514f1ba6c9c73be576bb02d89a8cf