Airworthiness Directives; Dassault Aviation Airplanes

[Federal Register Volume 89, Number 162 (Wednesday, August 21, 2024)]
[Rules and Regulations]
[Pages 67538-67540]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2024-18632]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2024-1008; Project Identifier MCAI-2024-00080-T; 
Amendment 39-22783; AD 2024-14-02]
RIN 2120-AA64


Airworthiness Directives; Dassault Aviation Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: The FAA is superseding Airworthiness Directive (AD) 2023-02-
13, which applied to certain Dassault Aviation Model FALCON 900EX 
airplanes. AD 2023-02-13 required revising the existing maintenance or 
inspection program, as applicable, to incorporate new or more 
restrictive airworthiness limitations. Since the FAA issued AD 2023-02-
13, the FAA has determined that new or more restrictive airworthiness 
limitations are necessary. This AD continues to require certain actions 
in AD 2023-02-13 and requires revising the existing maintenance or 
inspection program, as applicable, to incorporate new or more 
restrictive airworthiness limitations, as specified in a European Union 
Aviation Safety Agency (EASA) AD, which is incorporated by reference. 
The FAA is issuing this AD to address the unsafe condition on these 
products.

DATES: This AD is effective September 25, 2024.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of September 
25, 2024.
    The Director of the Federal Register approved the incorporation by 
reference of a certain other publication listed in this AD as of March 
17, 2023 (88 FR 8740, February 10, 2023).

ADDRESSES: 
    AD Docket: You may examine the AD docket at regulations.gov under 
Docket No. FAA-2024-1008; or in person at Docket Operations between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD 
docket contains this final rule, the mandatory continuing airworthiness 
information (MCAI), any comments received, and other information. The 
address for Docket Operations is U.S. Department of Transportation, 
Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 
New Jersey Avenue SE, Washington, DC 20590.
    Material Incorporated by Reference:
    <bullet> For EASA material, contact EASA, Konrad-Adenauer-Ufer 3, 
50668 Cologne, Germany; telephone +49 221 8999 000; email 
[email protected]; website easa.europa.eu. You may find this material 
on the EASA website ad.easa.europa.eu. It is also available at 
regulations.gov under Docket No. FAA-2024-1008.
    <bullet> You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th Street, 
Des Moines, WA. For information on the availability of this material at 
the FAA, call 206-231-3195.

FOR FURTHER INFORMATION CONTACT: Tom Rodriguez, Aviation Safety 
Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; 
telephone 206-231-3226; email [email protected].

SUPPLEMENTARY INFORMATION:

Background

    The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 
CFR part 39 to supersede AD 2023-02-13, Amendment 39-22320 (88 FR 8740, 
February 10, 2023) (AD 2023-02-13). AD 2023-02-13 applied to certain 
Dassault Aviation Model FALCON 900EX airplanes. AD 2023-02-13 required 
revising the existing maintenance or inspection program, as applicable, 
to incorporate new or more restrictive airworthiness limitations. The 
FAA issued AD 2023-02-13 to address reduced structural integrity of the 
airplane.
    The NPRM published in the Federal Register on April 23, 2024 (89 FR 
30289). The NPRM was prompted by AD 2024-0035, dated January 31, 2024, 
issued by EASA, which is the Technical Agent for the Member States of 
the European Union (EASA AD 2024-0035) (also referred to as the MCAI). 
The MCAI states that new or more restrictive airworthiness limitations 
have been developed.
    In the NPRM, the FAA proposed to continue to require certain 
actions in AD 2023-02-13 and to require revising the existing 
maintenance or inspection program, as applicable, to incorporate new or 
more restrictive airworthiness limitations, as specified in EASA AD 
2024-0035. The FAA is issuing this AD to address the unsafe condition 
on these products.
    You may examine the MCAI in the AD docket at regulations.gov under 
Docket No. FAA-2024-1008.

Discussion of Final Airworthiness Directive

Comments

    The FAA received no comments on the NPRM or on the determination of 
the cost to the public.

Conclusion

    This product has been approved by the aviation authority of another 
country and is approved for operation in the United States. Pursuant to 
the FAA's bilateral agreement with this State of Design Authority, it 
has notified the FAA of the unsafe condition described in the MCAI 
referenced above. The FAA reviewed the relevant data and determined 
that air safety requires adopting this AD as proposed. Accordingly, the 
FAA is issuing this AD to address the unsafe condition on this product. 
Except for minor editorial changes, this AD is adopted as proposed in 
the NPRM. None of the changes will increase the economic burden on any 
operator.

[[Page 67539]]

Related Material Under 1 CFR part 51

    EASA AD 2024-0035 specifies new or more restrictive airworthiness 
limitations for airplane structures and safe life limits.
    This AD also requires EASA AD 2022-0144, dated July 11, 2022, which 
the Director of the Federal Register approved for incorporation by 
reference as of March 17, 2023 (88 FR 8740, February 10, 2023).
    This material is reasonably available because the interested 
parties have access to it through their normal course of business or by 
the means identified in the ADDRESSES section.

Costs of Compliance

    The FAA estimates that this AD affects 88 airplanes of U.S. 
registry. The FAA estimates the following costs to comply with this AD:
    The FAA estimates the total cost per operator for the retained 
actions from AD 2023-02-13 to be $7,650 (90 work-hours x $85 per work-
hour).
    The FAA has determined that revising the existing maintenance or 
inspection program takes an average of 90 work-hours per operator, 
although the agency recognizes that this number may vary from operator 
to operator. Since operators incorporate maintenance or inspection 
program changes for their affected fleet(s), the FAA has determined 
that a per-operator estimate is more accurate than a per-airplane 
estimate.
    The FAA estimates the total cost per operator for the new actions 
to be $7,650 (90 work-hours x $85 per work-hour).

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Will not affect intrastate aviation in Alaska, and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by:
0
a. Removing airworthiness directive 2023-02-13, Amendment 39-22320 (88 
FR 8740, February 10, 2023); and
    b. Adding the following new airworthiness directive:

2024-14-02 Dassault Aviation: Amendment 39-22783; Docket No. FAA-
2024-1008; Project Identifier MCAI-2024-00080-T.

(a) Effective Date

    This airworthiness directive (AD) is effective September 25, 
2024.

(b) Affected ADs

    This AD replaces AD 2023-02-13, Amendment 39-22320 (88 FR 8740, 
February 10, 2023) (AD 2023-02-13).

(c) Applicability

    This AD applies to Dassault Aviation Model FALCON 900EX 
airplanes, certificated in any category, as identified in European 
Union Aviation Safety Agency (EASA) AD 2024-0035, dated January 31, 
2024 (EASA AD 2024-0035).

(d) Subject

    Air Transport Association (ATA) of America Code 05, Time Limits/
Maintenance Checks.

(e) Unsafe Condition

    This AD was prompted by a determination that new or more 
restrictive airworthiness limitations are necessary. The FAA is 
issuing this AD to address reduced structural integrity of the 
airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Retained Revision of the Existing Maintenance or Inspection 
Program, With a New Terminating Action

    This paragraph restates the requirements of paragraph (j) of AD 
2023-02-13, with a new terminating action. Except as specified in 
paragraph (h) of this AD: Comply with all required actions and 
compliance times specified in, and in accordance with, EASA AD 2022-
0144, dated July 11, 2022 (EASA AD 2022-0144). Accomplishing the 
revision of the existing maintenance or inspection program required 
by paragraph (j) of this AD terminates the requirements of this 
paragraph.

(h) Retained Exceptions to EASA 2022-0144, With No Changes

    This paragraph restates the exceptions specified in paragraph 
(k) of AD 2023-02-13, with no changes.
    (1) The requirements specified in paragraphs (1) and (2) of EASA 
AD 2022-0144 do not apply to this AD.
    (2) Paragraph (3) of EASA AD 2022-0144 specifies revising ``the 
approved AMP'' within 12 months after its effective date, but this 
AD requires revising the existing maintenance or inspection program, 
as applicable, within 90 days after March 17, 2023 (the effective 
date of AD 2023-02-13).
    (3) The initial compliance time for doing the tasks specified in 
paragraph (3) of EASA AD 2022-0144 is at the applicable ``associated 
thresholds'' specified in paragraph (3) of EASA AD 2022-0144, or 
within 90 days after March 17, 2023 (the effective date of AD 2023-
02-13), whichever occurs later.
    (4) The provisions specified in paragraphs (4) and (5) of EASA 
AD 2022-0144 do not apply to this AD.
    (5) The ``Remarks'' section of EASA AD 2020-0144 does not apply 
to this AD.

(i) Retained Restrictions on Alternative Actions and Intervals, With a 
New Exception

    This paragraph restates the requirements of paragraph (l) of AD 
2023-02-13, with a new exception. Except as required by paragraph 
(j) of this AD, after the maintenance or inspection program has been 
revised as required by paragraph (g) of this AD, no alternative 
actions (e.g., inspections) and intervals are allowed unless they 
are approved as specified in the provisions of the ``Ref. 
Publications'' section of EASA AD 2022-0144.

[[Page 67540]]

(j) New Revision of the Existing Maintenance or Inspection Program

    Except as specified in paragraph (k) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, EASA AD 2024-0035. Accomplishing the revision of 
the existing maintenance or inspection program required by this 
paragraph terminates the requirements of paragraph (g) of this AD.

(k) Exceptions to EASA AD 2024-0035

    (1) This AD does not adopt the requirements specified in 
paragraphs (1) and (2) of EASA AD 2024-0035.
    (2) Paragraph (3) of EASA AD 2024-0035 specifies revising ``the 
approved AMP,'' within 12 months after its effective date, but this 
AD requires revising the existing maintenance or inspection program, 
as applicable, within 90 days after the effective date of this AD.
    (3) The initial compliance time for doing the tasks specified in 
paragraph (3) of EASA AD 2024-0035 is at the applicable 
``limitations'' and ``associated thresholds'' as incorporated by the 
requirements of paragraph (3) of EASA AD 2024-0035, or within 90 
days after the effective date of this AD, whichever occurs later.
    (4) This AD does not adopt the provisions specified in 
paragraphs (4) and (5) of EASA AD 2024-0035.
    (5) This AD does not adopt the ``Remarks'' section of EASA AD 
2024-0035.

(l) New Provisions for Alternative Actions and Intervals

    After the existing maintenance or inspection program has been 
revised as required by paragraph (j) of this AD, no alternative 
actions (e.g., inspections) and intervals are allowed unless they 
are approved as specified in the provisions of the ``Ref. 
Publications'' section of EASA AD 2024-0035.

(m) Additional AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Validation Branch, FAA, has the authority to approve 
AMOCs for this AD, if requested using the procedures found in 14 CFR 
39.19. In accordance with 14 CFR 39.19, send your request to your 
principal inspector or responsible Flight Standards Office, as 
appropriate. If sending information directly to the manager of the 
International Validation Branch, mail it to the address identified 
in paragraph (n) of this AD. Information may be emailed to: [email protected]. Before using any approved AMOC, notify your 
appropriate principal inspector, or lacking a principal inspector, 
the manager of the responsible Flight Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, International 
Validation Branch, FAA; or EASA; or Dassault Aviation's EASA Design 
Organization Approval (DOA). If approved by the DOA, the approval 
must include the DOA-authorized signature.

(n) Additional Information

    For more information about this AD, contact Tom Rodriguez, 
Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, 
Westbury, NY 11590; telephone 206-231-3226; email 
[email protected].

(o) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the material listed in this 
paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this material as applicable to do the actions 
required by this AD, unless this AD specifies otherwise.
    (3) The following material was approved for IBR on September 25, 
2024.
    (i) European Union Aviation Safety Agency (EASA) AD 2024-0035, 
dated January 31, 2024.
    (ii) [Reserved]
    (4) The following material was approved for IBR on March 17, 
2023 (88 FR 8740, February 10, 2023).
    (i) European Union Aviation Safety Agency (EASA) AD 2022-0144, 
dated July 11, 2022.
    (ii) [Reserved]
    (5) For EASA AD 2024-0035 and EASA AD 2022-0144, contact EASA, 
Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 
8999 000; email [email protected]; website easa.europa.eu. You may 
find these EASA ADs on the EASA website ad.easa.europa.eu.
    (6) You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th 
Street, Des Moines, WA. For information on the availability of this 
material at the FAA, call 206-231-3195.
    (7) You may view this material at the National Archives and 
Records Administration (NARA). For information on the availability 
of this material at NARA, visit www.archives.gov/federal-register/cfr/ibr-locations, or email [email protected].

    Issued on July 10, 2024.
James D. Foltz,
Deputy Director, Compliance & Airworthiness Division, Aircraft 
Certification Service.
[FR Doc. 2024-18632 Filed 8-20-24; 8:45 am]
BILLING CODE 4910-13-P

The complete text was extracted from the official GovInfo HTML edition for this publication. Acquired 2026-10-09T01:28:41.298959+00:00. Text extraction preserves the recorded source wording; it does not determine current requirements.

Open the captured official edition

Source SHA-256

f805c445d5ac10a03cb60f9b89e65979fa00124b5b76298962ba62509fe99741

Text SHA-256

1a4d8e7b7874df7d985fd8e3c8e13ca50e9831f2dcca14614558828929795a01