Airworthiness Directives; Dassault Aviation Airplanes

[Federal Register Volume 91, Number 175 (Friday, September 11, 2026)]
[Rules and Regulations]
[Pages 57777-57780]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2026-18602]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2026-4662; Project Identifier MCAI-2026-00207-T; 
Amendment 39-23457; AD 2026-18-02]
RIN 2120-AA64


Airworthiness Directives; Dassault Aviation Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: The FAA is superseding Airworthiness Directive (AD) 2023-22-
12, which applied to all Dassault Aviation Model FALCON 2000 airplanes. 
AD 2023-22-12 required revising the existing maintenance or inspection 
program, as applicable, to incorporate new or more restrictive 
airworthiness limitations. Since the FAA issued AD 2023-22-12, the FAA 
has determined that new or more restrictive airworthiness limitations 
are necessary. This AD continues to require certain actions in AD 2023-
22-12 and requires revising the existing maintenance or inspection 
program, as applicable, to incorporate new or more restrictive 
airworthiness limitations. The FAA is issuing this AD to address the 
unsafe condition on these products.

DATES: This AD is effective October 16, 2026.

[[Page 57778]]

    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of October 16, 
2026.
    The Director of the Federal Register approved the incorporation by 
reference of a certain other publication listed in this AD as of 
December 27, 2023 (88 FR 81342, November 22, 2023).

ADDRESSES: 
    AD Docket: You may examine the AD docket at regulations.gov under 
Docket No. FAA-2026-4662; or in person at Docket Operations between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD 
docket contains this final rule, the mandatory continuing airworthiness 
information (MCAI), any comments received, and other information. The 
address for Docket Operations is U.S. Department of Transportation, 
Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 
New Jersey Avenue SE, Washington, DC 20590.
    Material Incorporated by Reference:
    <bullet> For European Union Aviation Safety Agency (EASA) material 
identified in this AD, contact EASA, Konrad-Adenauer-Ufer 3, 50668 
Cologne, Germany; telephone +49 221 8999 000; email [email protected]. 
You may find this material on the EASA website at ad.easa.europa.eu.
    <bullet> You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th St., Des 
Moines, WA. For information on the availability of this material at the 
FAA, call 206-231-3195. It is also available at regulations.gov under 
Docket No. FAA-2026-4662.

FOR FURTHER INFORMATION CONTACT: Amanda Pieraccini, Aviation Safety 
Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; 
phone: 516-228-7329; email: [email protected].

SUPPLEMENTARY INFORMATION:

Background

    The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 
CFR part 39 to supersede AD 2023-22-12, Amendment 39-22596 (88 FR 
81342, November 22, 2023) (AD 2023-22-12). AD 2023-22-12 applied to all 
Dassault Aviation Model FALCON 2000 airplanes. AD 2023-22-12 required 
revising the existing maintenance or inspection program, as applicable, 
to incorporate new or more restrictive airworthiness limitations. The 
FAA issued AD 2023-22-12 to address reduced controllability of the 
airplane.
    The NPRM was published in the Federal Register on June 30, 2026 (91 
FR 39575). The NPRM was prompted by AD 2026-0040, dated February 27, 
2026 (EASA AD 2026-0040) (also referred to as the MCAI), issued by 
EASA, which is the Technical Agent for the Member States of the 
European Union. The MCAI states that new or more restrictive 
airworthiness limitations have been developed.
    In the NPRM, the FAA proposed to continue to require certain 
actions in AD 2023-22-12 and require revising the existing maintenance 
or inspection program, as applicable, to incorporate new or more 
restrictive airworthiness limitations, as specified in EASA AD 2026-
0040. The FAA is issuing this AD to address the unsafe condition on 
these products.
    You may examine the MCAI in the AD docket at regulations.gov under 
Docket No. FAA-2026-4662.

Discussion of Final Airworthiness Directive

Comments

    The FAA received no comments on the NPRM or on the determination of 
the cost.

Conclusion

    These products have been approved by the civil aviation authority 
of another country and are approved for operation in the United States. 
Pursuant to the FAA's bilateral agreement with this State of Design 
Authority, that authority has notified the FAA of the unsafe condition 
described in the MCAI referenced above. The FAA reviewed the relevant 
data, considered any comments received, and determined that air safety 
requires adopting this AD as proposed. Accordingly, the FAA is issuing 
this AD to address the unsafe condition on these products. Except for 
minor editorial changes, this AD is adopted as proposed in the NPRM. 
None of the changes will increase the economic burden on any operator.

Material Incorporated by Reference Under 1 CFR Part 51

    EASA AD 2026-0040 specifies new or more restrictive airworthiness 
limitations for airplane structures and safe life limits.
    This AD also requires EASA AD 2023-0099, dated May 11, 2023, which 
the Director of the Federal Register approved for incorporation by 
reference as of December 27, 2023 (88 FR 81342, November 22, 2023).
    This material is reasonably available because the interested 
parties have access to it through their normal course of business or by 
the means identified in the ADDRESSES section.

Costs of Compliance

    The FAA estimates that this AD affects 150 airplanes of U.S. 
registry. The FAA estimates the following costs to comply with this AD:
    The FAA estimates the total cost per operator for the retained 
actions from AD 2023-22-12 to be $7,650 (90 work-hours x $85 per work-
hour).
    The FAA has determined that revising the existing maintenance or 
inspection program takes an average of 90 work-hours per operator, 
although the agency recognizes that this number may vary from operator 
to operator. Since operators incorporate maintenance or inspection 
program changes for their affected fleet(s), the FAA has determined 
that a per-operator estimate is more accurate than a per-airplane 
estimate. Therefore, the FAA estimates the average total cost per 
operator for the new actions to be $7,650 (90 work-hours x $85 per 
work-hour).

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Will not affect intrastate aviation in Alaska, and
    (3) Will not have a significant economic impact, positive or 
negative,

[[Page 57779]]

on a substantial number of small entities under the criteria of the 
Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by:
0
a. Removing Airworthiness Directive (AD) 2023-22-12, Amendment 39-22596 
(88 FR 81342, November 22, 2023); and
0
b. Adding the following new AD:

2026-18-02 Dassault Aviation: Amendment 39-23457; Docket No. FAA-
2026-4662; Project Identifier MCAI-2026-00207-T.

(a) Effective Date

    This airworthiness directive (AD) is effective October 16, 2026.

(b) Affected ADs

    This AD replaces AD 2023-22-12, Amendment 39-22596 (88 FR 81342, 
November 22, 2023) (AD 2023-22-12).

(c) Applicability

    This AD applies to all Dassault Aviation Model FALCON 2000 
airplanes, certificated in any category.

(d) Subject

    Air Transport Association (ATA) of America Code 05, Time Limits/
Maintenance Checks.

(e) Unsafe Condition

    This AD was prompted by a determination that new or more 
restrictive airworthiness limitations are necessary. The FAA is 
issuing this AD to address reduced controllability of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Retained Revision of the Existing Maintenance or Inspection 
Program, With a New Terminating Action

    This paragraph restates the requirements of paragraph (j) of AD 
2023-22-12, with a new terminating action. Except as specified in 
paragraph (h) of this AD: Comply with all required actions and 
compliance times specified in, and in accordance with, European 
Union Aviation Safety Agency (EASA) AD 2023-0099, dated May 11, 2023 
(EASA AD 2023-0099). Accomplishing the revision of the existing 
maintenance or inspection program required by paragraph (j) of this 
AD terminates the requirements of this paragraph.

(h) Retained Exceptions to EASA AD 2023-0099, With No Change

    This paragraph restates the exceptions specified in paragraph 
(k) of AD 2023-22-12, with no change.
    (1) This AD does not adopt the requirements specified in 
paragraphs (1) and (2) of EASA AD 2023-0099.
    (2) Paragraph (3) of EASA AD 2023-0099 specifies revising ``the 
approved AMP'' within 12 months after its effective date, but this 
AD requires revising the existing maintenance or inspection program, 
as applicable, within 90 days after December 27, 2023 (the effective 
date of AD 2023-22-12).
    (3) The initial compliance time for doing the tasks specified in 
paragraph (3) of EASA AD 2023-0099 is at the applicable 
``limitations'' and ``associated thresholds'' as incorporated by the 
requirements of paragraph (3) of EASA AD 2023-0099, or within 90 
days after December 27, 2023 (the effective date of AD 2023-22-12), 
whichever occurs later.
    (4) This AD does not adopt the provisions specified in 
paragraphs (4) and (5) of EASA AD 2023-0099.
    (5) This AD does not adopt the ``Remarks'' section of EASA AD 
2023-0099.

(i) Retained Provisions for Alternative Actions and Intervals, With a 
New Exception

    This paragraph restates the requirements of paragraph (l) of AD 
2023-22-12, with a new exception. Except as required by paragraph 
(j) of this AD, after the existing maintenance or inspection program 
has been revised as required by paragraph (g) of this AD, no 
alternative actions (e.g., inspections), and intervals are allowed 
unless they are approved as specified in the provisions of the 
``Ref. Publications'' section of EASA AD 2023-0099.

(j) New Revision of the Existing Maintenance or Inspection Program

    Except as specified in paragraph (k) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with EASA AD 2026-0040, dated February 27, 2026 (EASA AD 
2026-0040). Accomplishing the revision of the existing maintenance 
or inspection program required by this paragraph terminates the 
requirements of paragraph (g) of this AD.

(k) Exceptions to EASA AD 2026-0040

    (1) This AD does not adopt the requirements specified in 
paragraphs (1) and (2) of EASA AD 2026-0040.
    (2) Paragraph (3) of EASA AD 2026-0040 specifies revising the 
approved aircraft maintenance program (AMP) within 12 months after 
its effective date, but this AD requires revising the existing 
maintenance or inspection program, as applicable, within 90 days 
after the effective date of this AD.
    (3) The initial compliance time for doing the tasks specified in 
paragraph (3) of EASA AD 2026-0040 is at the applicable limitations 
and associated thresholds as incorporated by the requirements of 
paragraph (3) of EASA AD 2026-0040.
    (4) This AD does not adopt the provisions specified in 
paragraphs (4) and (5) of EASA AD 2026-0040.
    (5) This AD does not adopt the ``Remarks'' section of EASA AD 
2026-0040.

(l) New Provisions for Alternative Actions and Intervals

    After the existing maintenance or inspection program has been 
revised as required by paragraph (j) of this AD, no alternative 
actions (e.g., inspections) and intervals are allowed unless they 
are approved as specified in the provisions of the ``Ref. 
Publications'' section of EASA AD 2026-0040.

(m) Additional AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Validation Branch, FAA, has the authority to approve 
AMOCs for this AD, if requested using the procedures found in 14 CFR 
39.19. In accordance with 14 CFR 39.19, send your request to your 
principal inspector or responsible Flight Standards Office, as 
appropriate. If sending information directly to the manager of the 
International Validation Branch, send it to the attention of the 
person identified in paragraph (n) of this AD and email to: 
[email protected]. Before using any approved AMOC, notify your 
appropriate principal inspector, or lacking a principal inspector, 
the manager of the responsible Flight Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, International 
Validation Branch, FAA; or EASA; or Dassault Aviation's EASA Design 
Organization Approval (DOA). If approved by the DOA, the approval 
must include the DOA-authorized signature.

(n) Additional Information

    For more information about this AD, contact Amanda Pieraccini, 
Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, 
Westbury, NY 11590; phone: 516-228-7329; email: [email protected].

(o) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the material listed in this 
paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this material as applicable to do the actions 
required by this AD, unless this AD specifies otherwise.
    (3) The following material was approved for IBR on October 16, 
2026.
    (i) European Union Aviation Safety Agency (EASA) AD 2026-0040, 
dated February 27, 2026.
    (ii) [Reserved]
    (4) The following material was approved for IBR on December 27, 
2023 (88 FR 81342, November 22, 2023).

[[Page 57780]]

    (i) European Union Aviation Safety Agency (EASA) AD 2023-0099, 
dated May 11, 2023.
    (ii) [Reserved]
    (5) For EASA material identified in this AD, contact EASA, 
Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 
8999 000; email [email protected]. You may find this material on 
the EASA website at ad.easa.europa.eu.
    (6) You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th St., 
Des Moines, WA. For information on the availability of this material 
at the FAA, call 206-231-3195.
    (7) You may view this material at the National Archives and 
Records Administration (NARA). For information on the availability 
of this material at NARA, visit www.archives.gov/federal-register/cfr/ibr-locations or email [email protected].

    Issued on August 31, 2026.
Paul R. Bernado,
Director, Compliance & Airworthiness Division, Aircraft Certification 
Service.
[FR Doc. 2026-18602 Filed 9-10-26; 8:45 am]
BILLING CODE 4910-13-P

The complete text was extracted from the official GovInfo HTML edition for this publication. Acquired 2026-10-09T00:46:14.186101+00:00. Text extraction preserves the recorded source wording; it does not determine current requirements.

Open the captured official edition

Source SHA-256

a402eefff274e2781b15f9ad9f13532e10007c3cd2ae1dee6d08b9d0005b97f8

Text SHA-256

b2be6bf7ff25965ed6f2d143dcf727cc5323fae6dec5efb8501de960318a2ad7