Published 1997-11-12 · Federal Register document 97-29445
Airworthiness Directives; Dornier Model 328-100 Series Airplanes
Publication summary
This amendment adopts a new airworthiness directive (AD), applicable to certain Dornier Model 328-100 series airplanes, that requires modifying the main landing gear (MLG) bay areas by installing additional slush protection covers in those areas. This amendment is prompted by the identification of a problem during flight test analysis, which indicated that slush can accumulate in the MLG bay areas. The actions specified by this AD are intended to prevent the accumulation of slush in the MLG bay areas, which could freeze and interfere with the landing gear or render it inoperative.
Why this record is shown
Source: Federal Register annual FAA metadata. Acquired 2026-09-03T22:22:50.512496+00:00. The title, summary and date are source facts.
- Source revision
- federal_register_ad_metadata_1997-4a95ddfbb930f223
- Source row
- results[267]
- Raw source SHA-256
- 4a95ddfbb930f2233fe4761cd510a4d543aa97184cc49c0aa329cb16e563cf78
Final-rule publication
Recorded publication clauses
- AD identifier printed in this edition
- 97-23-11
- Effective date printed in this edition
- 1997-12-17
Some source clauses remain unstructured. Read the complete publication for conditions that have not been interpreted here.
Read 2 complete recorded clauses
Applicability wording · Applicability
Applicability: Model 328-100 series airplanes, serial numbers
3005 through 3063 inclusive, certificated in any category.
Note 1: This AD applies to each airplane identified in the
preceding applicability provision, regardless of whether it has been
otherwise modified, altered, or repaired in the area subject to the
requirements of this AD. For airplanes that have been modified,
altered, or repaired so that the performance of the requirements of
this AD is affected, the owner/operator must request approval for an
alternative method of compliance in accordance with paragraph (b) of
this AD. The request should include an assessment of the effect of
the modification, alteration, or repair on the unsafe condition
addressed by this AD; and, if the unsafe condition has not been
eliminated, the request should include specific proposed actions to
address it.
Exact source excerpt. Text positions 5405–6289, end exclusive, in the original decoded publication. SHA-256: 3fd9f37c1ca0bb8922ceb4cc853666a7487906d80ec2ca2b6babf46acda9b4a1
Compliance and requirements
Compliance: Required as indicated, unless accomplished
previously.
To prevent the accumulation of slush in the main landing gear
(MLG) bay areas that could freeze and interfere with the landing
gear and result in it becoming inoperative, accomplish the
following:
(a) Within 90 days after the effective date of this AD, modify
the MLG bay areas by installing additional slush protection covers
in those areas in accordance with Dornier Service Bulletin SB-328-
30-132, dated October 11, 1995.
(b) An alternative method of compliance or adjustment of the
compliance time that provides an acceptable level of safety may be
used if approved by the Manager, International Branch, ANM-116, FAA,
Transport Airplane Directorate. Operators shall submit their
requests through an appropriate FAA Principal Maintenance Inspector,
who may add comments and then send it to International Branch, ANM-
116.
Note 2: Information concerning the existence of approved
alternative methods of compliance with this AD, if any, may be
obtained from the International Branch, ANM-116.
(c) Special flight permits may be issued in accordance with
sections 21.197 and 21.199 of the Federal Aviation Regulations (14
CFR 21.197 and 21.199) to operate the airplane to a location where
the requirements of this AD can be accomplished.
(d) The modification shall be done in accordance with Dornier
Service Bulletin SB-328-30-132, dated October 11, 1995. This
incorporation by reference was approved by the Director of the
Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part
51. Copies may be obtained from Dornier Deutsche Aerospace, P.O. Box
1103, D-82230 Wessling, Federal Republic of Germany. Copies may be
inspected at the FAA, Transport Airplane Directorate, 1601 Lind
Avenue, SW., Renton, Washington; or at the Office of the Federal
Register, 800 North Capitol Street, NW., suite 700, Washington, DC.
Note 3: The subject of this AD is addressed in German
airworthiness directive 95-412, dated November 2, 1995.
(e) This amendment becomes effective on December 17, 1997.
Exact source excerpt. Text positions 6289–8414, end exclusive, in the original decoded publication. SHA-256: 606e1d029c1e4fd1fcd09b5f1be6fe06add9f977d93fc660b7dbea70b4079104
No replacement link has been established from this edition. The complete historical rule chain and current legal effect remain unknown.
Find all recorded historical references to AD 97-23-11 · 0 printed reference observations in this pinned collection.
These are observations from one dated publication. Current legal status is unknown; aircraft applicability, installed configuration, compliance and burden require separate evidence. Missing or unparsed conditions remain unknown.
Why these observations are shown
They were extracted offline from the same immutable official HTML source as the complete recorded text. The dated source wording, original text coordinates and exact quote digests are retained. PDF/text agreement and current regulatory effect have not been qualified.
Observation revision: whole-ad-publication-clause-observations-1.0.1. Text SHA-256: 6cde7f140b5724a32b9c9270a7029ce4db8654f3c2e0e8a21a1b5dc1bdcdb6c5. Source manifest: 8e84d056bf089a29c9ba01f7d56c928be4f0d7616bc7cbda3d3a608e2e740ebe.
Official source · 1997-11-12
Publication text
This is the complete recorded text of this dated publication.
Current legal effect is unknown. Aircraft applicability, installed configuration and compliance require separate evidence. PDF/text agreement has not been evaluated.
Read the complete official publication text
[Federal Register Volume 62, Number 218 (Wednesday, November 12, 1997)]
[Rules and Regulations]
[Pages 60642-60643]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 97-29445]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. 96-NM-219-AD; Amendment 39-10199; AD 97-23-11]
RIN 2120-AA64
Airworthiness Directives; Dornier Model 328-100 Series Airplanes
AGENCY: Federal Aviation Administration, DOT.
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: This amendment adopts a new airworthiness directive (AD),
applicable to certain Dornier Model 328-100 series airplanes, that
requires modifying the main landing gear (MLG) bay areas by installing
additional slush protection covers in those areas. This amendment is
prompted by the identification of a problem during flight test
analysis, which indicated that slush can accumulate in the MLG bay
areas. The actions specified by this AD are intended to prevent the
accumulation of slush in the MLG bay areas, which could freeze and
interfere with the landing gear or render it inoperative.
DATES: Effective December 17, 1997.
The incorporation by reference of certain publications listed in
the regulations is approved by the Director of the Federal Register as
of December 17, 1997.
ADDRESSES: The service information referenced in this AD may be
obtained from Dornier Deutsche Aerospace, P.O. Box 1103, D-82230
Wessling, Federal Republic of Germany. This information may be examined
at the Federal Aviation Administration (FAA), Transport Airplane
Directorate, Rules Docket, 1601 Lind Avenue, SW., Renton, Washington;
or at the Office of the Federal Register, 800 North Capitol Street,
NW., suite 700, Washington, DC.
FOR FURTHER INFORMATION CONTACT: International Branch, ANM-116, FAA,
Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton,
Washington 98055-4056; telephone (425) 227-2110; fax (425) 227-1149.
SUPPLEMENTARY INFORMATION: A proposal to amend part 39 of the Federal
Aviation Regulations (14 CFR part 39) to include an airworthiness
directive (AD) that is applicable to certain Dornier Model 328-100
series airplanes was published in the Federal Register on March 12,
1997 (62 FR 11390). That action proposed to require modifying the main
landing gear (MLG) bay areas by installing additional slush protection
covers in those areas.
Comments
Interested persons have been afforded an opportunity to participate
in the making of this amendment. No comments were submitted in response
to the proposal or the FAA's determination of the cost to the public.
Conclusion
The FAA has determined that air safety and the public interest
require the adoption of the rule as proposed.
Cost Impact
The FAA estimates that 40 Dornier Model 328-100 series airplanes of
U.S. registry will be affected by this AD, that it will take
approximately 8 work hours per airplane to accomplish the required
actions, and that the average labor rate is $60 per work hour. The cost
of required parts will be negligible. Based on these figures, the cost
impact of the AD on U.S. operators is estimated to be $19,200, or $480
per airplane.
The cost impact figure discussed above is based on assumptions that
no operator has yet accomplished any of the requirements of this AD
action, and that no operator would accomplish those actions in the
future if this AD were not adopted.
Regulatory Impact
The regulations adopted herein will not have substantial direct
effects on the States, on the relationship between the national
government and the States, or on the distribution of power and
responsibilities among the various levels of government. Therefore, in
accordance with Executive Order 12612, it is determined that this final
rule does not have sufficient federalism implications to warrant the
preparation of a Federalism Assessment.
For the reasons discussed above, I certify that this action (1) is
not a ``significant regulatory action'' under Executive Order 12866;
(2) is not a ``significant rule'' under DOT Regulatory Policies and
Procedures (44 FR 11034, February 26, 1979); and (3) will not have a
significant economic impact, positive or negative, on a substantial
number of small entities under the criteria of the Regulatory
Flexibility Act. A final evaluation has been prepared for this action
and it is contained in the Rules Docket. A copy of it may be obtained
from the Rules Docket at the location provided under the caption
ADDRESSES.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
[[Page 60643]]
Adoption of the Amendment
Accordingly, pursuant to the authority delegated to me by the
Administrator, the Federal Aviation Administration amends part 39 of
the Federal Aviation Regulations (14 CFR part 39) as follows:
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
2. Section 39.13 is amended by adding the following new
airworthiness directive:
97-23-11 Dornier: Amendment 39-10199. Docket 96-NM-219-AD.
Applicability: Model 328-100 series airplanes, serial numbers
3005 through 3063 inclusive, certificated in any category.
Note 1: This AD applies to each airplane identified in the
preceding applicability provision, regardless of whether it has been
otherwise modified, altered, or repaired in the area subject to the
requirements of this AD. For airplanes that have been modified,
altered, or repaired so that the performance of the requirements of
this AD is affected, the owner/operator must request approval for an
alternative method of compliance in accordance with paragraph (b) of
this AD. The request should include an assessment of the effect of
the modification, alteration, or repair on the unsafe condition
addressed by this AD; and, if the unsafe condition has not been
eliminated, the request should include specific proposed actions to
address it.
Compliance: Required as indicated, unless accomplished
previously.
To prevent the accumulation of slush in the main landing gear
(MLG) bay areas that could freeze and interfere with the landing
gear and result in it becoming inoperative, accomplish the
following:
(a) Within 90 days after the effective date of this AD, modify
the MLG bay areas by installing additional slush protection covers
in those areas in accordance with Dornier Service Bulletin SB-328-
30-132, dated October 11, 1995.
(b) An alternative method of compliance or adjustment of the
compliance time that provides an acceptable level of safety may be
used if approved by the Manager, International Branch, ANM-116, FAA,
Transport Airplane Directorate. Operators shall submit their
requests through an appropriate FAA Principal Maintenance Inspector,
who may add comments and then send it to International Branch, ANM-
116.
Note 2: Information concerning the existence of approved
alternative methods of compliance with this AD, if any, may be
obtained from the International Branch, ANM-116.
(c) Special flight permits may be issued in accordance with
sections 21.197 and 21.199 of the Federal Aviation Regulations (14
CFR 21.197 and 21.199) to operate the airplane to a location where
the requirements of this AD can be accomplished.
(d) The modification shall be done in accordance with Dornier
Service Bulletin SB-328-30-132, dated October 11, 1995. This
incorporation by reference was approved by the Director of the
Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part
51. Copies may be obtained from Dornier Deutsche Aerospace, P.O. Box
1103, D-82230 Wessling, Federal Republic of Germany. Copies may be
inspected at the FAA, Transport Airplane Directorate, 1601 Lind
Avenue, SW., Renton, Washington; or at the Office of the Federal
Register, 800 North Capitol Street, NW., suite 700, Washington, DC.
Note 3: The subject of this AD is addressed in German
airworthiness directive 95-412, dated November 2, 1995.
(e) This amendment becomes effective on December 17, 1997.
Issued in Renton, Washington, on November 3, 1997.
Darrell M. Pederson,
Acting Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. 97-29445 Filed 11-10-97; 8:45 am]
BILLING CODE 4910-13-U
Why this text is shown
The complete text was extracted from the official GovInfo HTML edition for this publication. Acquired 2026-10-09T05:08:14.252142+00:00. Text extraction preserves the recorded source wording; it does not determine current requirements.
Open the captured official edition
- Source SHA-256
- 990a77d3ceafc074fc5f38673661993fe164ad238da01e917382dfa43343fc2a
- Text SHA-256
- 6cde7f140b5724a32b9c9270a7029ce4db8654f3c2e0e8a21a1b5dc1bdcdb6c5
Return to the full metadata catalog · Search complete publication text · Explore retained publication text and evidence
Coverage and limits
These are dated publication metadata, recorded clauses and literal source observations. Word, model-label, header and reference matches do not establish current legal effect, manufacturer/model identity, aircraft applicability, installed configuration or compliance.
The collection uses 33 explicit annual source snapshots. Source captures and operative-text qualifications have separate states. Missing information remains unknown.