Airworthiness Directives; Saab Model SAAB 2000 Series Airplanes

[Federal Register Volume 63, Number 152 (Friday, August 7, 1998)]
[Rules and Regulations]
[Pages 42213-42214]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 98-21101]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. 98-NM-151-AD; Amendment 39-10699; AD 98-16-22]
RIN 2120-AA64


Airworthiness Directives; Saab Model SAAB 2000 Series Airplanes

AGENCY: Federal Aviation Administration, DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: This amendment adopts a new airworthiness directive (AD), 
applicable to certain Saab Model SAAB 2000 series airplanes, that 
requires a one-time inspection for cracking of the rear pressure 
bulkhead; and installation of a reinforcement angle on the rear 
pressure bulkhead; or repair, if necessary. This amendment is prompted 
by issuance of mandatory continuing airworthiness information by a 
foreign civil airworthiness authority. The actions specified by this AD 
are intended to prevent cracking of the rear pressure bulkhead, which 
could result in sudden loss of cabin pressure and the inability to 
withstand fail-safe loads.

DATES: Effective September 11, 1998.
    The incorporation by reference of certain publications listed in 
the regulations is approved by the Director of the Federal Register as 
of September 11, 1998.

ADDRESSES: The service information referenced in this AD may be 
obtained from Saab Aircraft AB, SAAB Aircraft Product Support, S-
581.88, Linkping, Sweden. This information may be examined at the 
Federal Aviation Administration (FAA), Transport Airplane Directorate, 
Rules Docket, 1601 Lind Avenue, SW., Renton, Washington; or at the 
Office of the Federal Register, 800 North Capitol Street, NW., suite 
700, Washington, DC.

FOR FURTHER INFORMATION CONTACT: Norman B. Martenson, Manager, 
International Branch, ANM-116, FAA, Transport Airplane Directorate, 
1601 Lind Avenue, SW., Renton, Washington 98055-4056; telephone (425) 
227-2110; fax (425) 227-1149.

SUPPLEMENTARY INFORMATION: A proposal to amend part 39 of the Federal 
Aviation Regulations (14 CFR part 39) to include an airworthiness 
directive (AD) that is applicable to certain Saab Model SAAB 2000 
series airplanes was published in the Federal Register on June 9, 1998 
(63 FR 31380). That action proposed to require a one-time inspection 
for cracking of the rear pressure bulkhead; and installation of a 
reinforcement angle on the rear pressure bulkhead; or repair, if 
necessary.

Comments

    Interested persons have been afforded an opportunity to participate 
in the making of this amendment. No comments were submitted in response 
to the proposal or the FAA's determination of the cost to the public.

Conclusion

    The FAA has determined that air safety and the public interest 
require the adoption of the rule as proposed.

Cost Impact

    The FAA estimates that 3 airplanes of U.S. registry will be 
affected by this AD.
    It will take approximately 6 work hours per airplane to accomplish 
the required inspection, at an average labor rate of $60 per work hour. 
Based on these figures, the cost impact of the inspection required by 
this AD on U.S. operators is estimated to be $1,080, or $360 per 
airplane.
    The required installation will take approximately 10 work hours per 
airplane, at an average labor rate of $60 per work hour. Based on these 
figures, the cost impact of the installation required by this AD on 
U.S. operators is estimated to be $1,800, or $600 per airplane.
    The cost impact figures discussed above are based on assumptions 
that no operator has yet accomplished any of the requirements of this 
AD action, and that no operator would accomplish those actions in the 
future if this AD were not adopted.

Regulatory Impact

    The regulations adopted herein will not have substantial direct 
effects on the States, on the relationship between the national 
government and the States, or on the distribution of power and 
responsibilities among the various levels of government. Therefore, in 
accordance with Executive Order 12612, it is determined that this final 
rule does not have sufficient federalism implications to warrant the 
preparation of a Federalism Assessment.
    For the reasons discussed above, I certify that this action (1) is 
not a ``significant regulatory action'' under Executive Order 12866; 
(2) is not a ``significant rule'' under DOT Regulatory Policies and 
Procedures (44 FR 11034, February 26, 1979); and (3) will not have a 
significant economic impact, positive or negative, on a substantial 
number of small entities under the criteria of the Regulatory 
Flexibility Act. A final evaluation has been prepared for this action 
and it is contained in the Rules Docket. A copy of it may be obtained 
from the Rules Docket at the location provided under the caption 
ADDRESSES.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, pursuant to the authority delegated to me by the 
Administrator, the Federal Aviation Administration amends part 39 of 
the Federal Aviation Regulations (14 CFR part 39) as follows:

PART 39--AIRWORTHINESS DIRECTIVES

    1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec. 39.13  [Amended]

    2. Section 39.13 is amended by adding the following new 
airworthiness directive:

98-16-22  SAAB AIRCRAFT AB: Amendment 39-10699. Docket 98-NM-151-AD.

    Applicability: Model SAAB 2000 series airplanes, manufacturer 
serial numbers 004 through 050 inclusive, 052, 053, and 054; 
certificated in any category.

    Note 1: This AD applies to each airplane identified in the 
preceding applicability provision, regardless of whether it has been 
modified, altered, or repaired in the area subject to the 
requirements of this AD. For airplanes that have been modified, 
altered, or repaired so that the performance of the requirements of 
this AD is affected, the owner/operator must request approval for an 
alternative method of compliance in accordance with paragraph (b) of 
this AD. The request should include an assessment of the effect of 
the modification, alteration, or repair on the unsafe condition 
addressed by this AD; and, if the unsafe condition has not been 
eliminated, the request should include specific proposed actions to 
address it.

    Compliance: Required as indicated, unless accomplished 
previously.
    To prevent cracking on the rear pressure bulkhead, which could 
result in sudden loss

[[Page 42214]]

of cabin pressure and the inability to withstand fail-safe loads, 
accomplish the following:
    (a) Within 4,000 flight cycles after the effective date of this 
AD, perform a one-time visual inspection for cracking on the rear 
pressure bulkhead in the area of the lower forward flange that 
connects to the fuselage skin, in accordance with SAAB Service 
Bulletin 2000-53-026, dated February 27, 1998.
    (1) If no crack is detected, prior to further flight, install a 
reinforcement angle on the rear pressure bulkhead in the area of the 
lower forward flange that connects to the fuselage skin, in 
accordance with the service bulletin. After accomplishment of the 
installation, no further action is required by this AD.
    (2) If any crack is detected, prior to further flight, repair in 
accordance with a method approved by either the Manager, 
International Branch, ANM-116, FAA, Transport Airplane Directorate, 
or the Luftfartsverket (or its delegated agent).
    (b) An alternative method of compliance or adjustment of the 
compliance time that provides an acceptable level of safety may be 
used if approved by the Manager, International Branch, ANM-116. 
Operators shall submit their request through an appropriate FAA 
Principal Maintenance Inspector, who may add comments and then send 
it to the Manager, International Branch, ANM-116.

    Note 2: Information concerning the existence of approved 
alternative methods of compliance with this AD, if any, may be 
obtained from the International Branch, ANM-116.

    (c) Special flight permits may be issued in accordance with 
sections 21.197 and 21.199 of the Federal Aviation Regulations (14 
CFR 21.197 and 21.199) to operate the airplane to a location where 
the requirements of this AD can be accomplished.
    (d) The inspection and installation shall be done in accordance 
with SAAB Service Bulletin 2000-53-026, dated February 27, 1998. 
This incorporation by reference was approved by the Director of the 
Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 
51. Copies may be obtained from Saab Aircraft AB, SAAB Aircraft 
Product Support, S-581.88, Linkoping, Sweden. Copies may be 
inspected at the FAA, Transport Airplane Directorate, 1601 Lind 
Avenue, SW., Renton, Washington; or at the Office of the Federal 
Register, 800 North Capitol Street, NW., suite 700, Washington, DC.

    Note 3: The subject of this AD is addressed in Swedish 
airworthiness directive 1-122, dated March 2, 1998.

    (e) This amendment becomes effective on September 11, 1998.

    Issued in Renton, Washington, on July 31, 1998.
Darrell M. Pederson,
Acting Manager,Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 98-21101 Filed 8-6-98; 8:45 am]
BILLING CODE 4910-13-U

The complete text was extracted from the official GovInfo HTML edition for this publication. Acquired 2026-10-09T04:59:41.575814+00:00. Text extraction preserves the recorded source wording; it does not determine current requirements.

Open the captured official edition

Source SHA-256

583be846bde2b2b6665da28a9c779706db1c3bae2bb0f364f95b3180a1f18882

Text SHA-256

9966e566cfaaf1ed642021d7924528103eb6b6c594cf32389153132c543d26aa