Airworthiness Directives; Gulfstream Aerospace LP Model Gulfstream 200 Airplanes

[Federal Register Volume 72, Number 63 (Tuesday, April 3, 2007)]
[Rules and Regulations]
[Pages 15816-15818]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: E7-5898]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2007-27737; Directorate Identifier 2007-NM-029-AD; 
Amendment 39-15008; AD 2007-07-11]
RIN 2120-AA64


Airworthiness Directives; Gulfstream Aerospace LP Model 
Gulfstream 200 Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule; request for comments.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for the 
products listed above. This AD results from mandatory continuing 
airworthiness information (MCAI) originated by an aviation authority of 
another country to identify and correct an unsafe condition on an 
aviation product. The MCAI describes the unsafe condition as:

    Due to quality escape during serial production, the jumpers at 
the Right Fuel Standby Pump Connector 4Q1 were manufactured from 14 
AWG electrical wiring instead of 12 AWG wires as required per 
approved drawing. The possible overheating of the 14 AWG jumpers 
routed in vicinity of the fuel tank may present the unsafe flight 
condition.

    This AD requires actions that are intended to address the unsafe 
condition described in the MCAI.

DATES: This AD becomes effective April 18, 2007.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication, listed in the AD as of April 18, 
2007.
    We must receive comments on this AD by May 3, 2007.

ADDRESSES: You may send comments by any of the following methods:
    <bullet> DOT Docket Web Site: Go to http://dms.dot.gov and follow 
the instructions for sending your comments electronically.
    <bullet> Fax: (202) 493-2251.
    <bullet> Mail: Docket Management Facility, U.S. Department of 
Transportation, 400 Seventh Street, SW., Nassif Building, Room PL-401, 
Washington, DC 20590-0001.
    <bullet> Hand Delivery: Room PL-401 on the plaza level of the 
Nassif Building, 400 Seventh Street, SW., Washington, DC, between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    <bullet> Federal eRulemaking Portal: http://www.regulations.gov. 
Follow the instructions for submitting comments.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://dms.dot.gov; or in person at the Docket Management Facility between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD 
docket contains this AD, the regulatory evaluation, any comments 
received, and other information. The street address for the Docket 
Office (telephone (800) 647-5227) is in the ADDRESSES section. Comments 
will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Mike Borfitz, Aerospace Engineer, 
International Branch, ANM-116, FAA, Transport Airplane Directorate, 
1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425) 
227-2677; fax (425) 227-1149.

SUPPLEMENTARY INFORMATION:

Streamlined Issuance of AD

    The FAA is implementing a new process for streamlining the issuance 
of ADs related to MCAI. This streamlined process will allow us to adopt 
MCAI safety requirements in a more efficient manner and will reduce 
safety risks to the public. This process continues to follow all FAA AD 
issuance processes to meet legal, economic, Administrative Procedure 
Act, and Federal Register requirements. We also continue to meet our 
technical decision-making responsibilities to identify and correct 
unsafe conditions on U.S.-certificated products.
    This AD references the MCAI and related service information that we 
considered in forming the engineering basis to correct the unsafe 
condition. The AD contains text copied from the MCAI and for this 
reason might not follow our plain language principles.

Discussion

    The Civil Aviation Authority of Israel (CAAI), which is the 
aviation authority for Israel, has issued Israeli Airworthiness 
Directive 28-07-02-03, dated February 11, 2007 (referred to after this 
as ``the MCAI''), to correct an unsafe condition for the specified 
products. The MCAI states:

    Due to quality escape during serial production, the jumpers at 
the Right Fuel Standby Pump Connector 4Q1 were manufactured from 14 
AWG electrical wiring instead of 12 AWG wires as required per 
approved drawing. The possible overheating of the 14 AWG jumpers 
routed in vicinity of the fuel tank may present the unsafe flight 
condition.

    The corrective actions include replacing the wiring, inspecting for 
other components damaged by overheating, and replacing damaged 
components if necessary. You may obtain further information by 
examining the MCAI in the AD docket.

Relevant Service Information

    Gulfstream has issued Alert Service Bulletin 200-28A-315, dated 
February 5, 2007. The actions described in this service information are 
intended to correct the unsafe condition identified in the MCAI.

FAA's Determination and Requirements of This AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified of the unsafe condition described in the MCAI and service 
information referenced above. We are issuing this AD because we 
evaluated all pertinent information and determined the unsafe condition 
exists and is likely to exist or develop on other products of the same 
type design.

Differences Between the AD and the MCAI or Service Information

    We have reviewed the MCAI and related service information and, in 
general, agree with their substance. But we might have found it 
necessary to use different words from those in the MCAI to ensure the 
AD is clear for U.S. operators and is enforceable. In making these 
changes, we do not intend to differ substantively from the information 
provided in the MCAI and related service information.
    We might also have required different actions in this AD from those 
in the MCAI in order to follow FAA policies. Any such differences are 
highlighted in a NOTE within the AD.

FAA's Determination of the Effective Date

    An unsafe condition exists that requires the immediate adoption of 
this AD. The FAA has found that the risk to the flying public justifies 
waiving notice

[[Page 15817]]

and comment prior to adoption of this rule because, due to a quality 
escape during serial production, the jumpers at the right fuel standby 
pump connector 4Q1 were manufactured from 14 AWG electrical wiring 
instead of 12 AWG wires as required per approved drawing. The 
overheating of the 14 AWG jumpers routed in vicinity of the fuel tank 
may cause the unsafe flight condition. Therefore, we determined that 
notice and opportunity for public comment before issuing this AD are 
impracticable and that good cause exists for making this amendment 
effective in fewer than 30 days.

Comments Invited

    This AD is a final rule that involves requirements affecting flight 
safety, and we did not precede it by notice and opportunity for public 
comment. We invite you to send any written relevant data, views, or 
arguments about this AD. Send your comments to an address listed under 
the ADDRESSES section. Include ``Docket No. FAA-2007-27737; Directorate 
Identifier 2007-NM-029-AD'' at the beginning of your comments. We 
specifically invite comments on the overall regulatory, economic, 
environmental, and energy aspects of this AD. We will consider all 
comments received by the closing date and may amend this AD because of 
those comments.
    We will post all comments we receive, without change, to http://dms.dot.gov, including any personal information you provide. We will 
also post a report summarizing each substantive verbal contact we 
receive about this AD.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this AD will not have federalism implications 
under Executive Order 13132. This AD will not have a substantial direct 
effect on the States, on the relationship between the national 
government and the States, or on the distribution of power and 
responsibilities among the various levels of government.
    For the reasons discussed above, I certify this AD:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979); and
    3. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this AD and placed it in the AD docket.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

0
Accordingly, under the authority delegated to me by the Administrator, 
the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new AD:

2007-07-11 Gulfstream Aerospace LP (Formerly Israel Aircraft 
Industries, Ltd.): Amendment 39-15008. Docket No. FAA-2007-27737; 
Directorate Identifier 2007-NM-029-AD.

Effective Date

    (a) This airworthiness directive (AD) becomes effective April 
18, 2007.

Affected ADs

    (b) None.

Applicability

    (c) This AD applies to Gulfstream Model Gulfstream 200 
airplanes, certificated in any category, serial numbers 121 through 
154.

Subject

    (d) Fuel.

Reason

    (e) The mandatory continued airworthiness information (MCAI) 
states:
    Due to quality escape during serial production, the jumpers at 
the Right Fuel Standby Pump Connector 4Q1 were manufactured from 14 
AWG electrical wiring instead of 12 AWG wires as required per 
approved drawing. The possible overheating of the 14 AWG jumpers 
routed in vicinity of the fuel tank may present the unsafe flight 
condition.
    The corrective actions include replacing the wiring, inspecting 
for other components damaged by overheating, and replacing damaged 
components if necessary.

Actions and Compliance

    (f) Within 25 flight hours or 30 days, whichever occurs first, 
after the effective date of this AD, unless already done, do the 
following actions.
    (1) Replace the wiring according to the Gulfstream Alert Service 
Bulletin 200-28A-315, dated February 5, 2007.
    (2) Do a general visual inspection for other components damaged 
by overheating. Replace all damaged components, before further 
flight, using a method approved by either the Manager, International 
Branch, ANM-116, Transport Airplane Directorate, FAA; or the Civil 
Aviation Authority of Israel (CAAI) (or its delegated agent). One 
approved method is the Gulfstream G200 Maintenance Manual.

    Note 1: For the purposes of this AD, a general visual inspection 
is: ``A visual examination of an interior or exterior area, 
installation, or assembly to detect obvious damage, failure, or 
irregularity. This level of inspection is made from within touching 
distance unless otherwise specified. A mirror may be necessary to 
ensure visual access to all surfaces in the inspection area. This 
level of inspection is made under normally available lighting 
conditions such as daylight, hangar lighting, flashlight, or 
droplight and may require removal or opening of access panels or 
doors. Stands, ladders, or platforms may be required to gain 
proximity to the area being checked.''

FAA AD Differences

    Note 2: This AD differs from the MCAI and/or service information 
as follows:
    (1) The MCAI specifies to ``inspect and replace the wiring'' and 
``replace other components damaged by overheating.'' However, this 
AD requires replacing the wiring, inspecting for other components 
damaged by overheating, and replacing damaged components as 
applicable. We have defined the inspection as a ``general visual 
inspection.''
    (2) The MCAI does not specify service information for replacing 
components other than wiring. We require that the replacements be 
done in accordance with a method approved by the FAA or CAAI.

Other FAA AD Provisions

    (g) The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Branch, ANM-116, FAA, has the authority to approve 
AMOCs for this AD, if requested using the procedures found in 14 CFR 
39.19. Send information to ATTN: Mike Borfitz,

[[Page 15818]]

Aerospace Engineer, International Branch, ANM-116, FAA, Transport 
Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington 
98057-3356; telephone (425) 227-2677; fax (425) 227-1149. Before 
using any AMOC approved in accordance with Sec.  39.19 on any 
airplane to which the AMOC applies, notify the appropriate principal 
inspector in the FAA Flight Standards Certificate Holding District 
Office.
    (2) Airworthy Product: For any requirement in this AD to obtain 
corrective actions from a manufacturer or other source, use these 
actions if they are FAA-approved. Corrective actions are considered 
FAA-approved if they are approved by the State of Design Authority 
(or their delegated agent). You are required to assure the product 
is airworthy before it is returned to service.
    (3) Reporting Requirements: For any reporting requirement in 
this AD, under the provisions of the Paperwork Reduction Act, the 
Office of Management and Budget (OMB) has approved the information 
collection requirements and has assigned OMB Control Number 2120-
0056.

Related Information

    (h) Refer to MCAI Israeli Airworthiness Directive 28-07-02-03, 
dated February 11, 2007, and Gulfstream Alert Service Bulletin 200-
28A-315, dated February 5, 2007, for related information.

Material Incorporated by Reference

    (i) You must use Gulfstream Alert Service Bulletin 200-28A-315, 
dated February 5, 2007, to do the actions required by this AD, 
unless the AD specifies otherwise.
    (1) The Director of the Federal Register approved the 
incorporation by reference of this service information under 5 
U.S.C. 552(a) and 1 CFR part 51.
    (2) For service information identified in this AD, contact 
Gulfstream Aerospace Corporation, P.O. Box 2206, Mail Station D-25, 
Savannah, Georgia 31402-2206.
    (3) You may review copies at the FAA, Transport Airplane 
Directorate, 1601 Lind Avenue, SW., Renton, Washington; or at the 
National Archives and Records Administration (NARA). For information 
on the availability of this material at NARA, call (202) 741-6030, 
or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued in Renton, Washington, on March 23, 2007.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
 [FR Doc. E7-5898 Filed 4-2-07; 8:45 am]
BILLING CODE 4910-13-P

The complete text was extracted from the official GovInfo HTML edition for this publication. Acquired 2026-10-09T03:39:18.611510+00:00. Text extraction preserves the recorded source wording; it does not determine current requirements.

Open the captured official edition

Source SHA-256

598dba4aa715c4cd4e50cfc7fcd4840dffe13c660625c5cd272432c3111fce43

Text SHA-256

cbb62671a1fab76d6f3776980bb1a59d9483fa484499590211523991195cd597