Published 2009-08-27 · Federal Register document E9-20284
Airworthiness Directives; CFM International, S.A. CFM56-5B1/P; -5B2/P; -5B3/P; -5B3/P1; -5B4/P; -5B4/P1; -5B5/P; -5B6/P; -5B7/P; -5B8/P; -5B9/P; -5B1/3; -5B2/3; -5B3/3; -5B4/3; -5B5/3; -5B6/3; -5B7/3; -5B8/3; -5B9/3; -5B3/3B1; and -5B4/3B1 Turbofan Engines
Publication summary
The FAA is adopting a new airworthiness directive (AD) for CFM International, S.A. CFM56-5B1/P; -5B2/P; -5B3/P; -5B3/P1; -5B4/P; -5B4/ P1; -5B5/P; -5B6/P; -5B7/P; -5B8/P; -5B9/P; -5B1/3; -5B2/3; -5B3/3; - 5B4/3; -5B5/3; -5B6/3; -5B7/3; -5B8/3; -5B9/3; -5B3/3B1; and -5B4/3B1 turbofan engines. This AD requires initial and repetitive eddy current inspections (ECIs) of certain part number (P/N) low-pressure (LP) turbine rear frames. This AD results from a refined lifing analysis by the engine manufacturer that shows the need to identify initial and repetitive inspection thresholds for inspecting certain LP turbine rear frames. We are issuing this AD to detect low-cycle-fatigue cracks in the LP turbine rear frame, which could result in an engine separating from the airplane, causing damage to, and possibly leading to loss of control of the airplane.
Why this record is shown
Source: Federal Register annual FAA metadata. Acquired 2026-09-03T22:23:30.011257+00:00. The title, summary and date are source facts.
- Source revision
- federal_register_ad_metadata_2009-cb57e588bd107238
- Source row
- results[226]
- Raw source SHA-256
- cb57e588bd10723805ef0ea28ddc0685de14711012023c7e7d12178879efaeed
Final-rule publication
Recorded publication clauses
- AD identifier printed in this edition
- 2009-18-01
- Effective date printed in this edition
- 2009-10-01
Read 12 complete recorded clauses
Effective Date
Effective Date
(a) This airworthiness directive (AD) becomes effective October
1, 2009.
Exact source excerpt. Text positions 8190–8285, end exclusive, in the original decoded publication. SHA-256: 19ca32b39a42f1d635cede04f6c0f847330a9117ed3df6a02e9e099cd88fb6dc
Affected ADs
Affected ADs
(b) None.
Exact source excerpt. Text positions 8285–8314, end exclusive, in the original decoded publication. SHA-256: 027fbc44617399472b6ac4741da3aee18448654374228bcf4fe3f01df6b1539b
Applicability wording · Applicability
Applicability
(c) This AD applies to:
(1) CFM International, S.A. turbofan engines with a low-pressure
(LP) turbine rear frame, part number (P/N) 338-171-703-0; 338-171-
704-0; 338-171-705-0; or 338-171-706-0 installed, as follows:
(i) Commercial application CFM56-5B1/P; -5B2/P; -5B3/P; -5B3/P1;
-5B4/P; -5B4/P1; -5B5/P; -5B6/P; -5B7/P; -5B8/P; -5B9/P turbofan
engines.
(ii) Corporate application CFM56-5B6/P and -5B7/P turbofan
engines.
(2) CFM International, S.A. turbofan engines with an LP turbine
rear frame, P/N 338-171-751-0; or 338-171-752-0 installed, on
corporate and commercial applications of CFM56-5B1/P; -5B2/P; -5B3/
P; -5B3/P1; -5B4/P; -5B4/P1; -5B5/P; -5B6/P; -5B7/P; -5B8/P; -5B9/P;
-5B1/3; -5B2/3; -5B3/3; -5B4/3; -5B5/3; -5B6/3; -5B7/3; -5B8/3; -
5B9/3; -5B3/3B1; and -5B4/3B1 turbofan engines.
(3) These engines are installed on, but not limited to, Airbus
A318, A319, A320, and A321 series airplanes.
Exact source excerpt. Text positions 8314–9272, end exclusive, in the original decoded publication. SHA-256: 1fba060f7bc8fc3d94dfff600e0608ed5664aae96f61b13816fd24a711794182
Unsafe Condition
Unsafe Condition
(d) This AD results from a refined lifing analysis by the engine
manufacturer that shows the need to identify initial and repetitive
inspection thresholds for inspecting certain LP turbine rear frames.
We are issuing this AD to detect low-cycle-fatigue cracks in the LP
turbine rear frame, which could result in an engine separating from
the airplane, causing damage to, and possibly leading to loss of
control of the airplane.
Exact source excerpt. Text positions 9272–9729, end exclusive, in the original decoded publication. SHA-256: f11c389e9de9507c96f926adc2356f9c2b4d4a8fdc5e752e9b07c44204fdbf6b
Compliance
Compliance
(e) You are responsible for having the actions required by this
AD performed within the compliance times specified unless the
actions have already been done.
Exact source excerpt. Text positions 9729–9906, end exclusive, in the original decoded publication. SHA-256: 9b3c9e019fb507cf6548fcccdb7151b3e1278af7078c0a234a67c27b748f31df
Initial Inspection
Initial Inspection
(f) Perform an initial eddy current inspection (ECI) of the LP
turbine rear frame using paragraphs 3.A. through 3.A.(7)(d) of the
Accomplishment Instructions of CFM International, S.A. Service
Bulletin (SB) No. CFM56-5B S/B 72-0620, Revision 2, dated December
1, 2008, at the following compliance times:
(1) For commercial engine applications, within 25,000 cycles-
since-new (CSN) on the LP turbine rear frame.
(2) For corporate engine applications, within 19,000 CSN on the
LP turbine rear frame.
(3) For engines with unknown LP turbine rear frame CSN, within
300 cycles-in-service from the effective date of this AD.
Exact source excerpt. Text positions 9906–10569, end exclusive, in the original decoded publication. SHA-256: f3e950805e04cedfb05d024277170be392a8cadb2c19f38e0cba3f46a44e4840
Repetitive Inspections
Repetitive Inspections
(g) Perform repetitive ECIs of the LP turbine rear frame using
paragraphs 3.A. through 3.A.(7)(d) of the Accomplishment
Instructions of CFM International, S.A. SB No. CFM56-5B S/B 72-0620,
Revision 2, dated December 1, 2008. Use the inspection intervals in
paragraph 3.A.(8) of the Accomplishment Instructions of CFM
International, S.A. SB No. CFM56-5B S/B 72-0620, Revision 2, dated
December 1, 2008.
Exact source excerpt. Text positions 10569–11006, end exclusive, in the original decoded publication. SHA-256: f18a7c0f22288041bf80af21bbe4cfc4952574c7256368748c90717d3c1e61d7
LP Turbine Rear Frame Removal Criteria
LP Turbine Rear Frame Removal Criteria
(h) Remove LP turbine rear frames from service that have a
single crack length of 2.56 inches (65 mm) or longer, or multiple
cracks with an accumulated crack length of 2.56 inches (65 mm) or
longer.
Exact source excerpt. Text positions 11006–11253, end exclusive, in the original decoded publication. SHA-256: fa351e146a83b63cd6dbb4e5a178e68bb0fd8526add9ac0b9b21d4965f6e12ab
Previous Credit
Previous Credit
(i) Initial and repetitive inspections done before the effective
date of this AD using CFM International, S.A. SB No. CFM56-5B S/B
72-0620, dated May 3, 2007, or SB No. CFM56-5B S/B 72-0620, Revision
1, dated December 20, 2007, comply with the initial and repetitive
inspection requirements specified in this AD. Operators must
continue performing the repetitive inspections required in paragraph
(g) of this AD.
Exact source excerpt. Text positions 11253–11694, end exclusive, in the original decoded publication. SHA-256: 4e11b1625b380a7dd9c1d20d6d35baa1bf4c0b1345f02a1973d4d783a5d1c03c
Alternative Methods of Compliance
Alternative Methods of Compliance
(j) The Manager, Engine Certification Office, has the authority
to approve alternative methods of compliance for this AD if
requested using the procedures found in 14 CFR 39.19.
[[Page 43636]]
Exact source excerpt. Text positions 11694–11930, end exclusive, in the original decoded publication. SHA-256: 547e8737abb8caa56dd48663c4246839d66a264a738c78efcb89f947bc61df2c
Related Information
Related Information
(k) European Aviation Safety Agency AD 2009-0110, dated May 7,
2009, also addresses the subject of this AD.
(l) Contact Stephen Sheely, Aerospace Engineer, Engine
Certification Office, FAA, Engine and Propeller Directorate, 12 New
England Executive Park, Burlington, MA 01803; e-mail:
[email protected]; telephone (781) 238-7750; fax (781) 238-
7199, for more information about this AD.
Exact source excerpt. Text positions 11930–12351, end exclusive, in the original decoded publication. SHA-256: 41595cb118c1c2f0406b393695cbc7d1ad7549a091a57202cb0a57cbcbe52e30
Material Incorporated by Reference
Material Incorporated by Reference
(m) You must use CFM International, S.A. SB No. CFM56-5B S/B 72-
0620, Revision 2, dated December 1, 2008 to perform the inspections
required by this AD. The Director of the Federal Register approved
the incorporation by reference of this service bulletin in
accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Contact CFM
International, Technical Publications Department, 1 Neumann Way,
Cincinnati, OH 45215; telephone (513) 552-2800; fax (513) 552-2816,
for a copy of this service information. You may review copies at the
FAA, New England Region, 12 New England Executive Park, Burlington,
MA; or at the National Archives and Records Administration (NARA).
For information on the availability of this material at NARA, call
202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.
Exact source excerpt. Text positions 12351–13216, end exclusive, in the original decoded publication. SHA-256: 6e34ad4b621a984593d0429c0cc4e6683324b6babbb55c0a7ba0a54d609c7d58
No replacement link has been established from this edition. The complete historical rule chain and current legal effect remain unknown.
Find all recorded historical references to AD 2009-18-01 · 0 printed reference observations in this pinned collection.
These are observations from one dated publication. Current legal status is unknown; aircraft applicability, installed configuration, compliance and burden require separate evidence. Missing or unparsed conditions remain unknown.
Why these observations are shown
They were extracted offline from the same immutable official HTML source as the complete recorded text. The dated source wording, original text coordinates and exact quote digests are retained. PDF/text agreement and current regulatory effect have not been qualified.
Observation revision: whole-ad-publication-clause-observations-1.0.1. Text SHA-256: b94abaa0be62f65c9a0a238c368c7d16c552fdf1b580ef74bb435c557434da38. Source manifest: aabf100250ca3013a4ace964f0ea8230ba23a3fca1406aef40f3ff1c8f7620e0.
Official source · 2009-08-27
Publication text
This is the complete recorded text of this dated publication.
Current legal effect is unknown. Aircraft applicability, installed configuration and compliance require separate evidence. PDF/text agreement has not been evaluated.
Read the complete official publication text
[Federal Register Volume 74, Number 165 (Thursday, August 27, 2009)]
[Rules and Regulations]
[Pages 43634-43636]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: E9-20284]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2008-0174; Directorate Identifier 2008-NE-03-AD;
Amendment 39-15997; AD 2009-18-01]
RIN 2120-AA64
Airworthiness Directives; CFM International, S.A. CFM56-5B1/P; -
5B2/P; -5B3/P; -5B3/P1; -5B4/P; -5B4/P1; -5B5/P; -5B6/P; -5B7/P; -5B8/
P; -5B9/P; -5B1/3; -5B2/3; -5B3/3; -5B4/3; -5B5/3; -5B6/3; -5B7/3; -
5B8/3; -5B9/3; -5B3/3B1; and -5B4/3B1 Turbofan Engines
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: The FAA is adopting a new airworthiness directive (AD) for CFM
International, S.A. CFM56-5B1/P; -5B2/P; -5B3/P; -5B3/P1; -5B4/P; -5B4/
P1; -5B5/P; -5B6/P; -5B7/P; -5B8/P; -5B9/P; -5B1/3; -5B2/3; -5B3/3; -
5B4/3; -5B5/3; -5B6/3; -5B7/3; -5B8/3; -5B9/3; -5B3/3B1; and -5B4/3B1
turbofan engines. This AD requires initial and repetitive eddy current
inspections (ECIs) of certain part number (P/N) low-pressure (LP)
turbine rear frames. This AD results from a refined lifing analysis by
the engine manufacturer that shows the need to identify initial and
repetitive inspection thresholds for inspecting certain LP turbine rear
frames. We are issuing this AD to detect low-cycle-fatigue cracks in
the LP turbine rear frame, which could result in an engine separating
from the airplane, causing damage to, and possibly leading to loss of
control of the airplane.
DATES: This AD becomes effective October 1, 2009. The Director of the
Federal Register approved the incorporation by reference of certain
publications listed in the regulations as of October 1, 2009.
ADDRESSES: You can get the service information identified in this AD
from CFM International, Technical Publications Department, 1 Neumann
Way, Cincinnati, OH 45215; telephone (513) 552-2800; fax (513) 552-
2816.
The Docket Operations office is located at Docket Management
Facility, U.S. Department of Transportation, 1200 New Jersey Avenue,
SE., West Building Ground Floor, Room W12-140, Washington, DC 20590-
0001.
FOR FURTHER INFORMATION CONTACT: Stephen Sheely, Aerospace Engineer,
Engine Certification Office, FAA, Engine and Propeller Directorate, 12
New England Executive Park, Burlington, MA 01803; e-mail:
[email protected]; telephone (781) 238-7750; fax (781) 238-7199.
SUPPLEMENTARY INFORMATION: The FAA proposed to amend 14 CFR part 39
with a proposed AD and a supplemental proposed AD. The proposed AD
applies to CFM International, S.A. CFM56-5B1/P; -5B2/P; -5B3/P; -5B3/
P1; -5B4/P; -5B4/P1; -5B5/P; -5B6/P; -5B7/P; -5B8/P; and -5B9/P
turbofan engines, and the supplemental proposed AD applies to CFM
International, S.A. CFM56-5B1/P; -5B2/P; -5B3/P; -5B3/P1; -5B4/P; -5B4/
P1; -5B5/P; -5B6/P; -5B7/P; -5B8/P; -5B9/P; -5B1/3; -5B2/3; -5B3/3; -
5B4/3; -5B5/3; -5B6/3; -5B7/3; -5B8/3; -5B9/3; -5B3/3B1; and -5B4/3B1
turbofan engines. We published the proposed AD in the Federal Register
on May 7, 2008 (73 FR 25597). That action proposed to require initial
and repetitive ECIs of certain P/N LP turbine rear frames. We published
the supplemental proposed AD in the Federal Register on April 24, 2009
(74 FR 18662). That action proposed to require initial and repetitive
ECIs of those same P/N LP turbine rear frames, to add two additional P/
N LP turbine rear frames, to add 11 engine models to the applicability,
and to clarify the commercial and corporate engines/LP turbine rear
frames applicability.
Examining the AD Docket
You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Operations office
between 9 a.m. and 5 p.m., Monday through Friday, except Federal
holidays. The AD docket contains this AD, the regulatory evaluation,
any comments received, and other information. The street address for
the Docket Operations office (telephone (800) 647-5527) is provided in
the ADDRESSES section. Comments will be available in the AD docket
shortly after receipt.
Comments
We provided the public the opportunity to participate in the
development of this AD. We have considered the comment received.
One commenter, CFM International, S.A. requests that we reference
the latest European Aviation Safety Agency AD 2009-0110, dated May 7,
2009, as it is up-to-date on P/Ns and engine models affected.
We agree and changed the AD to reference AD 2009-0110.
[[Page 43635]]
Conclusion
We have carefully reviewed the available data, including the
comment received, and determined that air safety and the public
interest require adopting the AD with the changes described previously.
We have determined that these changes will neither increase the
economic burden on any operator nor increase the scope of the AD.
Costs of Compliance
We estimate that this AD will affect 282 CFM56-5B series turbofan
engines installed on airplanes of U.S. registry. We estimate that it
will take about 3 work-hours to perform an eddy current inspection of
an LP turbine rear frame. The average labor rate is $80 per work-hour.
A replacement LP turbine rear frame costs about $102,240. If all 282 LP
turbine rear frames needed replacement, we estimate the total cost of
the AD to U.S. operators to be $28,899,360. Our cost estimate is
exclusive of possible warranty coverage.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII, Aviation Programs,
describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in
subtitle VII, part A, subpart III, section 44701, ``General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
We have determined that this AD will not have federalism
implications under Executive Order 13132. This AD will not have a
substantial direct effect on the States, on the relationship between
the national government and the States, or on the distribution of power
and responsibilities among the various levels of government.
For the reasons discussed above, I certify that this AD:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866;
(2) Is not a ``significant rule'' under DOT Regulatory Policies and
Procedures (44 FR 11034, February 26, 1979); and
(3) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared a summary of the costs to comply with this AD and
placed it in the AD Docket. You may get a copy of this summary at the
address listed under ADDRESSES.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
0
Accordingly, under the authority delegated to me by the Administrator,
the Federal Aviation Administration amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by adding the following new airworthiness
directive:
2009-18-01 CFM International, S.A.: Amendment 39-15997. Docket No.
FAA-2008-0174; Directorate Identifier 2008-NE-03-AD.
Effective Date
(a) This airworthiness directive (AD) becomes effective October
1, 2009.
Affected ADs
(b) None.
Applicability
(c) This AD applies to:
(1) CFM International, S.A. turbofan engines with a low-pressure
(LP) turbine rear frame, part number (P/N) 338-171-703-0; 338-171-
704-0; 338-171-705-0; or 338-171-706-0 installed, as follows:
(i) Commercial application CFM56-5B1/P; -5B2/P; -5B3/P; -5B3/P1;
-5B4/P; -5B4/P1; -5B5/P; -5B6/P; -5B7/P; -5B8/P; -5B9/P turbofan
engines.
(ii) Corporate application CFM56-5B6/P and -5B7/P turbofan
engines.
(2) CFM International, S.A. turbofan engines with an LP turbine
rear frame, P/N 338-171-751-0; or 338-171-752-0 installed, on
corporate and commercial applications of CFM56-5B1/P; -5B2/P; -5B3/
P; -5B3/P1; -5B4/P; -5B4/P1; -5B5/P; -5B6/P; -5B7/P; -5B8/P; -5B9/P;
-5B1/3; -5B2/3; -5B3/3; -5B4/3; -5B5/3; -5B6/3; -5B7/3; -5B8/3; -
5B9/3; -5B3/3B1; and -5B4/3B1 turbofan engines.
(3) These engines are installed on, but not limited to, Airbus
A318, A319, A320, and A321 series airplanes.
Unsafe Condition
(d) This AD results from a refined lifing analysis by the engine
manufacturer that shows the need to identify initial and repetitive
inspection thresholds for inspecting certain LP turbine rear frames.
We are issuing this AD to detect low-cycle-fatigue cracks in the LP
turbine rear frame, which could result in an engine separating from
the airplane, causing damage to, and possibly leading to loss of
control of the airplane.
Compliance
(e) You are responsible for having the actions required by this
AD performed within the compliance times specified unless the
actions have already been done.
Initial Inspection
(f) Perform an initial eddy current inspection (ECI) of the LP
turbine rear frame using paragraphs 3.A. through 3.A.(7)(d) of the
Accomplishment Instructions of CFM International, S.A. Service
Bulletin (SB) No. CFM56-5B S/B 72-0620, Revision 2, dated December
1, 2008, at the following compliance times:
(1) For commercial engine applications, within 25,000 cycles-
since-new (CSN) on the LP turbine rear frame.
(2) For corporate engine applications, within 19,000 CSN on the
LP turbine rear frame.
(3) For engines with unknown LP turbine rear frame CSN, within
300 cycles-in-service from the effective date of this AD.
Repetitive Inspections
(g) Perform repetitive ECIs of the LP turbine rear frame using
paragraphs 3.A. through 3.A.(7)(d) of the Accomplishment
Instructions of CFM International, S.A. SB No. CFM56-5B S/B 72-0620,
Revision 2, dated December 1, 2008. Use the inspection intervals in
paragraph 3.A.(8) of the Accomplishment Instructions of CFM
International, S.A. SB No. CFM56-5B S/B 72-0620, Revision 2, dated
December 1, 2008.
LP Turbine Rear Frame Removal Criteria
(h) Remove LP turbine rear frames from service that have a
single crack length of 2.56 inches (65 mm) or longer, or multiple
cracks with an accumulated crack length of 2.56 inches (65 mm) or
longer.
Previous Credit
(i) Initial and repetitive inspections done before the effective
date of this AD using CFM International, S.A. SB No. CFM56-5B S/B
72-0620, dated May 3, 2007, or SB No. CFM56-5B S/B 72-0620, Revision
1, dated December 20, 2007, comply with the initial and repetitive
inspection requirements specified in this AD. Operators must
continue performing the repetitive inspections required in paragraph
(g) of this AD.
Alternative Methods of Compliance
(j) The Manager, Engine Certification Office, has the authority
to approve alternative methods of compliance for this AD if
requested using the procedures found in 14 CFR 39.19.
[[Page 43636]]
Related Information
(k) European Aviation Safety Agency AD 2009-0110, dated May 7,
2009, also addresses the subject of this AD.
(l) Contact Stephen Sheely, Aerospace Engineer, Engine
Certification Office, FAA, Engine and Propeller Directorate, 12 New
England Executive Park, Burlington, MA 01803; e-mail:
[email protected]; telephone (781) 238-7750; fax (781) 238-
7199, for more information about this AD.
Material Incorporated by Reference
(m) You must use CFM International, S.A. SB No. CFM56-5B S/B 72-
0620, Revision 2, dated December 1, 2008 to perform the inspections
required by this AD. The Director of the Federal Register approved
the incorporation by reference of this service bulletin in
accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Contact CFM
International, Technical Publications Department, 1 Neumann Way,
Cincinnati, OH 45215; telephone (513) 552-2800; fax (513) 552-2816,
for a copy of this service information. You may review copies at the
FAA, New England Region, 12 New England Executive Park, Burlington,
MA; or at the National Archives and Records Administration (NARA).
For information on the availability of this material at NARA, call
202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.
Issued in Burlington, Massachusetts, on August 17, 2009.
Peter A. White,
Assistant Manager, Engine and Propeller Directorate, Aircraft
Certification Service.
[FR Doc. E9-20284 Filed 8-26-09; 8:45 am]
BILLING CODE 4910-13-P
Why this text is shown
The complete text was extracted from the official GovInfo HTML edition for this publication. Acquired 2026-10-09T03:21:05.255386+00:00. Text extraction preserves the recorded source wording; it does not determine current requirements.
Open the captured official edition
- Source SHA-256
- d52037002d8ebb805a51fa09ed350e6aa069c4f82162cc9249f789f8f0b1b607
- Text SHA-256
- b94abaa0be62f65c9a0a238c368c7d16c552fdf1b580ef74bb435c557434da38
Return to the full metadata catalog · Search complete publication text · Explore retained publication text and evidence
Coverage and limits
These are dated publication metadata, recorded clauses and literal source observations. Word, model-label, header and reference matches do not establish current legal effect, manufacturer/model identity, aircraft applicability, installed configuration or compliance.
The collection uses 33 explicit annual source snapshots. Source captures and operative-text qualifications have separate states. Missing information remains unknown.